EEWORLDEEWORLDEEWORLD

Part Number

Search

SX63M330B1FL1230

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 63V, 20% +Tol, 20% -Tol, 330uF, Through Hole Mount, ROHS COMPLIANT
CategoryPassive components    capacitor   
File Size69KB,4 Pages
ManufacturerYAGEO
Websitehttp://www.yageo.com/
Environmental Compliance  
Download Datasheet Parametric View All

SX63M330B1FL1230 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 63V, 20% +Tol, 20% -Tol, 330uF, Through Hole Mount, ROHS COMPLIANT

SX63M330B1FL1230 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerYAGEO
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
capacitance330 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
dielectric materialsALUMINUM (WET)
ESR130 mΩ
leakage current0.2079 mA
Manufacturer's serial numberSX
Installation featuresTHROUGH HOLE MOUNT
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
Package shapeCYLINDRICAL PACKAGE
method of packingBULK
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)63 V
ripple current663 mA
surface mountNO
Delta tangent0.08
Terminal shapeWIRE
YAGEO CORPORATION
ALUMINUM ELECTROLYTIC CAPACITORS
SX
[ For Low Impedance & Low E.S.R ]
105°C Single-Ended Lead Aluminum Electrolytic Capacitors For High Frequency Applications
Miniature Size Aluminum
Electrolytic Capacitors
ELECTRICAL CHARACTERISTICS
Operating Temperature : -40° ~ +105°C
Working Voltage : 6.3 ~ 100V
Rate Capacitance Range : 1 ~ 15000µF
Capacitance Tolerance : -20 ~ +20%
DC Leakage Current (µA) : I = 0.01 CV or 3(µA) Whichever is greater.
( Measurements shall be Made After a 2 Minute Charge at Rated Working Voltage )
Dissipation Factor : at 120 Hz, 25°C
WV (V) : 6.3
10
16
25
35
50
63
80
100
D.F (%) : 19
16
14
12
10
8
8
7
7
For capacitor whose capacitance exceeds 1000µF. The value of D.F(%) is increased by 2% for every
addition of 1000µF.
Temperature Characteristics : at 120 Hz
WV (V)
:
Impedance : Z - 40°C / Z + 20°C
Case Dia
Load Life
øD
2000
3000
5000
Multiplier for Ripple Current
Frequency(Hz)
~4.4µF
5.6~33µF
34~330µF
331~1000µF
1200µF higher
50
0.30
0.40
0.60
0.65
0.85
120
0.40
0.50
0.70
0.90
0.90
300
0.50
0.60
0.80
0.90
0.95
1K
0.70
0.80
0.90
0.98
0.98
10K
0.80
0.90
0.95
1.00
1.00
100K
1.00
1.00
1.00
1.00
1.00
6.3
10
10
6
16
5
25
4
35
4
50
4
63
4
100
4
Used in switching regulator applications in com-
puters. Especially for high frequency.
Low impedance and E.S.R., high permissible ripple
current at high frequency and highter operation
temperature (-40°C to +105°C).
High Temperature Load Life at 105°C for 2000 ~
5000 Hours
DESCRIPTION
Load Life : At 105°C Assured with Full Rated Maximum Ripple Current Applied
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200% of Initial Requirement
(c) Leakage Current : Not Exceed the Initial Requirement
Shelf Life : 1000 Hours, No Voltage Applied, at 105°C
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200 % of Initial Requirement
(c) Leakage Current : Not Exceed 200% of Initial Requirement
DIAGRAM OF DIMENSIONS
4.0
5.0
6.0
8.0
10.0
12.0
13.0
16.0
18.0
22.0
F
1.5
2.0
2.5
3.5
5.0
0.45
0.5
Rubber Stand-off
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Temperature(°C)
Factor
65
1.80
85
1.50
105
1.00
Dimensions : mm
Vinyl Sleeve
(P.V.C)
Rubber End Seal
F 0.5
F 0.5
0.6
L
0.4Max.
15Min.
5Min.
D 0.5
L
15Min.
5Min.
D 0.5
7.5
10.0
0.8
0.8
Can anyone give me a "plug and play system architecture"? Thank you very much
Can anyone give me a "plug and play system architecture"? Thank you very much. My email address is: jerk66@163.com...
f56007 Embedded System
Comparative analysis of Samsung's three mainstream processors: s3c2440, s3c6410, and s5pv210
[b]Comparative Analysis of Samsung's Three Mainstream Processors s3c2440\s3c6410\s5pv210[/font][font=宋体][/font][/b][b]Comparison of 1, ARM[/font][font=宋体]architecture[/font][/b][align=left] S3C2440[fo...
sinlinx ARM Technology
The problem of grounding the output signal of the half-bridge inverter circuit
As shown in the figure, after the half-bridge inverter output passes through c5 and L1, it passes through two voltage-dividing resistors to form two detection signals s1 and s2. When laying out the PC...
shaorc Analog electronics
Five factors affecting the bootstrap circuit
1. Gate Charge required to enhance MGT 2. Iqbs - quiescent current for the high side driver circuitry 3. Currents within the level shifter of the control IC 4. MGT gate-source forward leakage current ...
安_然 Analog electronics
mux710,ppp dial
Hello everyone: I want to use mux710 to make a serial port multi-channel driver under 6.0, and use com3 (the physical serial port on the original board) to virtualize two serial ports, com7 (for at) a...
gucunlin Embedded System
Make full use of signal sources and virtual instruments in Proteus to speed up DSP program design (including logic analyzer testing)
External interrupt experiment on LaunchPad [[i] This post was last edited by Pinghu Qiuyue on 2013-5-13 22:42 [/i]]...
平湖秋月 Microcontroller MCU

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2107  126  1530  1793  2035  43  3  31  37  41 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号