PIC16(L)F1713/6 microcontrollers combine Intelligent Analog integration with low cost and extreme low power (XLP) to
suit a variety of general purpose applications. These 28-pin devices deliver on-chip op amps, Core Independent Periph-
erals (CLC, NCO and COG), Peripheral Pin Select and Zero-Cross Detect, providing for increased design flexibility.
Core Features:
• C Compiler Optimized RISC Architecture
• Only 49 Instructions
• Operating Speed:
- 0-32 MHz clock input
- 125 ns minimum instruction cycle
• Interrupt Capability
• 16-Level Deep Hardware Stack
• Up to Four 8-bit Timers
• One 16-bit Timer
• Power-on Reset (POR)
• Power-up Timer (PWRT)
• Low-Power Brown-out Reset (LPBOR)
• Programmable Watchdog Timer (WDT) up to
256s
• Programmable Code Protection
Digital Peripherals:
• Configurable Logic Cell (CLC):
- Integrated combinational and sequential logic
• Complementary Output Generator (COG):
- Rising/falling edge dead-band control/
blanking
• Numerically Controlled Oscillator (NCO):
- Generates true linear frequency control and
increased frequency resolution
- Input Clock: 0Hz < F
NCO
< 32 MHz
- Resolution: F
NCO
/220
• Capture/Compare/PWM (CCP) module
• PWM: Two 10-bit Pulse-Width Modulators
• Serial Communications:
- SPI, I
2
C, RS-232, RS-485, LIN compatible
- Auto-Baud Detect, auto-wake-up on start
• Up to 35 I/O Pins and One Input Pin:
- Individually programmable pull-ups
- Slew rate control
- Interrupt-on-change with edge-select
• Peripheral Pin Select (PPS):
- Enables pin mapping of digital I/O
Memory:
•
•
•
•
Up to 8 Kwords Flash Program Memory
Up to 1024 Bytes Data SRAM Memory
Direct, Indirect and Relative Addressing modes
High-Endurance Flash Data Memory (HEF)
- 128 bytes if nonvolatile data storage
- 100k erase/write cycles
Intelligent Analog Peripherals:
• Operational Amplifiers:
- Two configurable rail-to-rail op amps
- Selectable internal and external channels
- 2 MHz gain bandwidth product
• High-Speed Comparators:
- Up to two comparators
- 50 ns response time
- Rail-to-rail inputs
• 10-Bit Analog-to-Digital Converter (ADC):
- Up to 28 external channels
- Conversion available during Sleep
- Temperature indicator
• Zero-Cross Detector (ZCD):
- Detect when AC signal on pin crosses
ground
• 8-Bit Digital-to-Analog Converter (DAC):
- Output available externally
- Internal connections to comparators, op
amps, Fixed Voltage Reference (FVR) and
ADC
• Internal Voltage Reference module
Operating Characteristics:
• Operating Voltage Range:
- 1.8V to 3.6V (PIC16LF1713/6)
- 2.3V to 5.5V (PIC16F1713/6)
• Temperature Range:
- Industrial: -40°C to 85°C
- Extended: -40°C to 125°C
eXtreme Low-Power (XLP) Features:
•
•
•
•
Sleep mode: 50 nA @ 1.8V, typical
Watchdog Timer: 500 nA @ 1.8V, typical
Secondary Oscillator: 500 nA @ 32 kHz
Operating Current:
- 8 uA @ 32 kHz, 1.8V, typical
- 32 uA/MHz @ 1.8V, typical
2013-2016 Microchip Technology Inc.
DS40001726C-page 1
PIC16(L)F1713/6
Clocking Structure:
• 16 MHz Internal Oscillator Block:
- ±1% at calibration
- Selectable frequency range from 0 to 32 MHz
• 31 kHz Low-Power Internal Oscillator
• External Oscillator Block with:
- Three crystal/resonator modes up to 20 MHz
- Two external clock modes up to 20 MHz
• Fail-Safe Clock Monitor
• Two-Speed Oscillator Start-up
• Oscillator Start-up Timer (OST)
Programming/Debug Features:
• In-Circuit Debug Integrated On-Chip
• Emulation Header for Advanced Debug:
- Provides trace, background debug and up to
32 hardware break points
• In-Circuit Serial Programming™ (ICSP™) via Two
Pins
PIC16(L)F1713/6 Family Types
Program Memory
Flash (words)
Data Sheet Index
High-Endurance
Flash (bytes)
10-bit ADC (ch)
MSSP (I
2
C/SPI)
High-Speed/
Comparators
Data SRAM
(bytes)
5/8-bit DAC
Zero Cross
Debug
(1)
I/E
I/E
I/E
I/E
I/E
EUSART
Timers
(8/16-bit)
Op Amp
I/Os
(2)
PWM
COG
NCO
CCP
CLC
PPS
Device
PIC16(L)F1713
PIC16(L)F1716
PIC16(L)F1717
PIC16(L)F1718
PIC16(L)F1719
Note 1:
2:
(1)
(1)
(2)
4096
8192
8192
512
1024
1024
2048
2048
128
128
128
128
128
25
25
36
25
36
17
17
28
17
28
1/1
1/1
1/1
1/1
1/1
2
2
2
2
2
2
2
2
2
2
1
1
1
1
1
4/1
4/1
4/1
4/1
4/1
2
2
2
2
2
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
4
4
4
4
1
1
1
1
1
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
(2) 16384
(2) 16384
Debugging Methods: (I) – Integrated on Chip; (H) – using Debug Header; E – using Emulation Header.
One pin is input-only.
Data Sheet Index:
(Unshaded devices are described in this document.)
1:
DS40001726
PIC16(L)F1713/6 Data Sheet, 28-Pin Flash, 8-bit Microcontrollers.
2:
DS40001740
PIC16(L)F1717/8/9 Data Sheet, 28/40-Pin Flash, 8-bit Microcontrollers.
Note:
For other small form-factor package availability and marking information, please visit
http://www.microchip.com/packaging
or contact your local sales office.
DS40001726C-page 2
2013-2016 Microchip Technology Inc.
XLP
PIC16(L)F1713/6
Pin Diagrams
FIGURE 1:
28-PIN PDIP, SOIC, SSOP
V
PP
/MCLR/RE3
RA0
RA1
RA2
RA3
RA4
RA5
V
SS
RA7
RA6
RC0
RC1
RC2
RC3
1
2
3
4
5
28
27
26
25
24
23
22
21
20
19
18
17
16
15
RB7
RB6
RB5
RB4
RB3
RB2
RB1
RB0
V
DD
V
SS
RC7
RC6
RC5
RC4
6
7
8
9
10
11
12
13
14
Note:
See
Table 1
for the pin allocation table.
FIGURE 2:
28-PIN (U)QFN
28
27
26
25
24
23
22
RE3/MCLR/V
PP
RB7
RB6
RB5
RB4
RA1
RA0
PIC16(L)F1713/6
RA2
RA3
RA4
RA5
V
SS
RA7
RA6
RC0
Note:
See
Table 1
for the pin allocation table.
2013-2016 Microchip Technology Inc.
RC1
RC2
RC3
RC4
RC5
RC6
8
9
10
11
12
13
14
1
2
3
PIC16(L)F1713/6
4
5
6
7
21
20
19
18
17
16
15
RB3
RB2
RB1
RB0
V
DD
V
SS
RC7
DS40001726C-page 3
TABLE 1:
PDIP, SOIC,
SSOP
QFN, UQFN
28-PIN ALLOCATION TABLE (PIC16(L)F1713/6)
Comparator
Zero Cross
Reference
EUSART
Interrupt
Op Amp
Timers
Pull-up
MSSP
Basic
PWM
COG
DS40001726C-page 4
2013-2016 Microchip Technology Inc.
PIC16(L)F1713/6
NCO
ADC
DAC
CCP
(2)
I/O
RA0
RA1
RA2
RA3
RA4
RA5
RA6
RA7
RB0
RB1
RB2
RB3
RB4
RB5
RB6
RB7
RC0
RC1
RC2
RC3
2
3
4
5
6
7
10
9
21
22
23
24
25
26
27
28
11
12
13
14
27
28
1
2
3
4
7
6
18
19
20
21
22
23
24
25
8
9
10
11
AN0
AN1
AN2
AN3
AN4
Vref-
Vref+
C1IN0-
C2IN0-
C1IN1-
C2IN1-
C1IN0+
C2IN0+
C1IN1+
OPA1IN+
OPA1IN-
DAC2OUT1
T0CKI
(1)
CLCIN0
(1)
OPA1OUT
DAC1OUT1
CLCIN1
(1)
CLC
IOC
IOC
IOC
IOC
IOC
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
ICSPCLK
ICSPDAT
OSC2
CLKOUT
OSC1
CLKIN
nSS
(1)
IOC
IOC
IOC
AN12
AN10
AN8
AN9
AN11
AN13
C2IN1+
C1IN3-
C2IN3-
OPA2OUT
OPA2IN-
C1IN2-
C2IN2-
OPA2IN+
ZCD
COG1IN
(1)
INT
(1)
IOC
IOC
IOC
IOC
IOC
T1G
DAC1OUT2
DAC2OUT2
(1)
IOC
CLCIN2
(1)
CLCIN3
(1)
IOC
IOC
IOC
T1CKI
SOSCO
SOSCI
AN14
AN15
(1)
CCP2
(1)
CCP1
(1)
IOC
IOC
SCL/ SCK
(1)
IOC
Note 1: Default peripheral input. Alternate pins can be selected as the peripheral input with the PPS input selection registers.
2: All pin digital outputs default to PORT latch data. Alternate outputs can be selected as the peripheral digital output with the PPS output selection registers.
3: These peripheral functions are bidirectional. The output pin selections must be the same as the input pin selections.
4: Alternate outputs are excluded from solid shaded areas.
5: Alternate inputs are excluded from dot shaded areas.
PWM3OUT
PWM4OUT
NCO1OUT
(3)
CLC4OUT
CLC3OUT
CLC2OUT
SCK/SCL
OUT
(4)
SCK/SCL
(3)
COG1IN
CLCIN0
CLCIN1
CLCIN2
CLCIN3
T1CKI
T0CKI
CCP1
CCP2
RX(3)
T1G
SDI
CLC1OUT
COG1C
COG1D
COG1A
COG1B
C1OUT
C2OUT
TX/CK
CCP1
CCP2
(3)
SDA
DT(3)
SDO
IN
(5)
Note 1: Default peripheral input. Alternate pins can be selected as the peripheral input with the PPS input selection registers.
2: All pin digital outputs default to PORT latch data. Alternate outputs can be selected as the peripheral digital output with the PPS output selection registers.
3: These peripheral functions are bidirectional. The output pin selections must be the same as the input pin selections.
4: Alternate outputs are excluded from solid shaded areas.
5: Alternate inputs are excluded from dot shaded areas.
As the title says, why is there a download of Windows Mobile ****** Emulator Images on Microsoft's website but no download of Windows CE ****** Emulator Images? There is a "Microsoft Windows CE 5.0 De...
Develop data acquisition equipment RTU based on Linux embedded platformProject budget:￥ 10,000~60,000
Development cycle: 30 days
Project Category: Embedded
Bidding requirements:Project tag:RTUlinuxPro...
MSP has 7 addressing modes, and the addressing modes are similar to those of ARM, so the modes are similar. These low-level things can only be used by writing in assembly statements.MSP430 pin distrib...
CCS3.3 can be installed and opened normally by selecting the compatible mode, but when installing the emulator, the usb510 in the XDS510-USB2.0 driver folder cannot be opened or seen. What is going on...
Embedded System
京公网安备 11010802033920号
EEWORLD
