(Note 1) Derate by 4.1mW/°C when operating above 25°C. (When mounted on a 9 layer glass-epoxy board with 63mm x 55mm x 1.6mm dimension.)
Caution:
Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit
between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is operated
Hello everyone! I am using a PC that is not connected to other PCs. I only use it for development. I use ActiveSync to connect to the WINCE device. I can connect to SQLSERVER in the simulator, but whe...
Everyone, what should I do with the chips in the POS development kit? I also received a bunch of chips, but I don’t know how to use them. Has anyone received them? Didn’t TI claim that the 800 kit cou...
When measuring the frequency of tlc555, if C=180PF is selected and the output is required to be around 20KHZ, what should I pay attention to when matching R1 and R2? Why did I choose R1=18K and R2=110...
MSP4340 f5529 self-made minimum system board: What are the requirements for the crystal oscillator? Because I don't have the 8M crystal oscillator on the schematic, I took a 6M one. When I was downloa...
H3C was founded in November 2003. It was initially a joint venture between Huawei and 3COM and was wholly acquired by 3COM in November 2006. The company is currently investing in the development of hi...
In the early 1990s, portable phones were all the rage. With the rapid development of electronic technology, today's mobile phones can not only send emails and text messages, but also take photos, ch...[Details]
Today's portable medical devices allow patients to diagnose and treat themselves, move around freely, and even use the devices when they are out and about. To achieve the "easy to carry" feature, po...[Details]
Radio Frequency Identification (RFID) technology is a non-contact automatic identification technology that uses wireless radio frequency communication. Compared with the currently widely used barco...[Details]
Introduction
The market for wireless telemetry products is developing rapidly. Recently, the industry has also set off a revolution in wireless applications. Wireless telemetry technol...[Details]
As the application scope of medical equipment expands from hospitals to emergency response and home medical environments, its mobility will be determined by many factors. In addition, medical equip...[Details]
Controller Area Network (CAN) is a type of fieldbus. It is a serial communication network that effectively supports distributed control or real-time control and is recognized as one of the most pro...[Details]
This summary will introduce the transmitter characteristic test of TD terminal products - uplink power control. According to the 3GPP TS34.122 standard, UE uplink power control is divided into uplink ...[Details]
The overcurrent and overheating coordinated protection technology implemented by polymer positive temperature coefficient devices (PPTC) can protect motors, controllers and electronic components in...[Details]
summary
Theoretically explains how to set up a PFC boost regulator using a current sensing transformer with the UCC3817 control IC.
1. Schematic
The schematic diagram is show...[Details]
A well-designed electronic load is not designed just for use in the lab; it should be carefully designed and built to test actual power systems. This is true for military portable systems, such as ...[Details]
1. Introduction
The UCC28051 reference design is a 100W offline AC/DC voltage converter with power factor correction (PFC). This power module design is intended to illustrate how to proper...[Details]
Combined with Samsung's ARM9 series embedded processor S3C2410, this paper explains how to perform modular programming of LCD driver and how to statically load the driver into the system kernel.
...[Details]
A financial analyst pointed out that the signal reception problems of Apple's 3G iPhone may be caused by some defective chips.
Richard Windsor, an analyst at Nomura Securities, said in a resea...[Details]
1. Basic circuit characteristics of power amplifier
The basic circuit of the complementary symmetrical OTL power amplifier is shown in Figure ①. Among them: C1 is the signal input coupling ele...[Details]
The difference between CCD and CMOS sensors Mr.OH! briefly introduced CCD and CMOS in the second lecture, but for most students, what they see is a combination of integrated chips! The detailed int...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
