in the United States and other countries. PCI and PCI-X are trademarks of PCI-SIG and used under license. All other trademarks are the property of their respective owners.
DS312 July 19, 2013
Product Specification
www.xilinx.com
1
8
Spartan-3E FPGA Family:
Introduction and Ordering Information
Product Specification
DS312 (v4.1) July 19, 2013
Introduction
The Spartan®-3E family of Field-Programmable Gate
Arrays (FPGAs) is specifically designed to meet the needs
of high volume, cost-sensitive consumer electronic
applications. The five-member family offers densities
ranging from 100,000 to 1.6 million system gates, as shown
in
Table 1.
The Spartan-3E family builds on the success of the earlier
Spartan-3 family by increasing the amount of logic per I/O,
significantly reducing the cost per logic cell. New features
improve system performance and reduce the cost of
configuration. These Spartan-3E FPGA enhancements,
combined with advanced 90 nm process technology, deliver
more functionality and bandwidth per dollar than was
previously possible, setting new standards in the
programmable logic industry.
Because of their exceptionally low cost, Spartan-3E FPGAs
are ideally suited to a wide range of consumer electronics
applications, including broadband access, home
networking, display/projection, and digital television
equipment.
The Spartan-3E family is a superior alternative to mask
programmed ASICs. FPGAs avoid the high initial cost, the
lengthy development cycles, and the inherent inflexibility of
in the United States and other countries. PCI and PCI-X are trademarks of PCI-SIG and used under license. All other trademarks are the property of their respective owners.
DS312 (v4.1) July 19, 2013
Product Specification
www.xilinx.com
2
Spartan-3E FPGA Family: Introduction and Ordering Information
Architectural Overview
The Spartan-3E family architecture consists of five
fundamental programmable functional elements:
•
Configurable Logic Blocks (CLBs)
contain flexible
Look-Up Tables (LUTs) that implement logic plus
storage elements used as flip-flops or latches. CLBs
perform a wide variety of logical functions as well as
store data.
Input/Output Blocks (IOBs)
control the flow of data
between the I/O pins and the internal logic of the
device. Each IOB supports bidirectional data flow plus
3-state operation. Supports a variety of signal
standards, including four high-performance differential
standards. Double Data-Rate (DDR) registers are
included.
Block RAM
provides data storage in the form of
18-Kbit dual-port blocks.
Multiplier Blocks
accept two 18-bit binary numbers as
inputs and calculate the product.
•
Digital Clock Manager (DCM) Blocks
provide
self-calibrating, fully digital solutions for distributing,
delaying, multiplying, dividing, and phase-shifting clock
signals.
•
These elements are organized as shown in
Figure 1.
A ring
of IOBs surrounds a regular array of CLBs. Each device has
two columns of block RAM except for the XC3S100E, which
has one column. Each RAM column consists of several
18-Kbit RAM blocks. Each block RAM is associated with a
dedicated multiplier. The DCMs are positioned in the center
with two at the top and two at the bottom of the device. The
XC3S100E has only one DCM at the top and bottom, while
the XC3S1200E and XC3S1600E add two DCMs in the
middle of the left and right sides.
The Spartan-3E family features a rich network of traces that
interconnect all five functional elements, transmitting
signals among them. Each functional element has an
associated switch matrix that permits multiple connections
to the routing.
•
•
X-Ref Target - Figure 1
Figure 1:
Spartan-3E Family Architecture
DS312 (v4.1) July 19, 2013
Product Specification
www.xilinx.com
3
Spartan-3E FPGA Family: Introduction and Ordering Information
Configuration
Spartan-3E FPGAs are programmed by loading
configuration data into robust, reprogrammable, static
CMOS configuration latches (CCLs) that collectively control
all functional elements and routing resources. The FPGA’s
configuration data is stored externally in a PROM or some
other non-volatile medium, either on or off the board. After
applying power, the configuration data is written to the
FPGA using any of seven different modes:
•
•
•
•
•
•
Master Serial from a Xilinx Platform Flash PROM
Serial Peripheral Interface (SPI) from an
industry-standard SPI serial Flash
Byte Peripheral Interface (BPI) Up or Down from an
industry-standard x8 or x8/x16 parallel NOR Flash
Slave Serial, typically downloaded from a processor
Slave Parallel, typically downloaded from a processor
Boundary Scan (JTAG), typically downloaded from a
processor or system tester.
I/O Capabilities
The Spartan-3E FPGA SelectIO interface supports many
popular single-ended and differential standards.
Table 2
shows the number of user I/Os as well as the number of
differential I/O pairs available for each device/package
combination.
Spartan-3E FPGAs support the following single-ended
standards:
•
•
•
•
•
3.3V low-voltage TTL (LVTTL)
Low-voltage CMOS (LVCMOS) at 3.3V, 2.5V, 1.8V,
1.5V, or 1.2V
3V PCI at 33 MHz, and in some devices,
66 MHz
HSTL I and III at 1.8V, commonly used in memory
applications
SSTL I at 1.8V and 2.5V, commonly used for memory
applications
Spartan-3E FPGAs support the following differential
standards:
•
•
•
•
•
•
•
LVDS
Bus LVDS
mini-LVDS
RSDS
Differential HSTL (1.8V, Types I and III)
Differential SSTL (2.5V and 1.8V, Type I)
2.5V LVPECL inputs
Furthermore, Spartan-3E FPGAs support MultiBoot
configuration, allowing two or more FPGA configuration
bitstreams to be stored in a single parallel NOR Flash. The
FPGA application controls which configuration to load next
and when to load it.
Table 2:
Available User I/Os and Differential (Diff) I/O Pairs
Package
Footprint
Size (mm)
Device
XC3S100E
XC3S250E
XC3S500E
XC3S1200E
XC3S1600E
Notes:
1.
2.
3.
All Spartan-3E devices provided in the same package are pin-compatible as further described in Module 4,
Pinout Descriptions.
The number shown in
bold
indicates the maximum number of I/O and input-only pins. The number shown in (italics) indicates the number
of input-only pins.
The XC3S500E is available in the VQG100 Pb-free package and not the standard VQ100. The VQG100 and VQ100 pin-outs are identical
and general references to the VQ100 will apply to the XC3S500E.
VQ100
VQG100
16 x 16
User
66
(2)
9(7)
66
(7)
66
(3)
(7)
-
-
Diff
30
(2)
30
(2)
30
(2)
-
-
CP132
CPG132
8x8
User
83
(11)
92
(7)
92
(7)
-
-
Diff
35
(2)
41
(2)
41
(2)
-
-
TQ144
TQG144
22 x 22
User
108
(28)
108
(28)
-
-
-
Diff
40
(4)
40
(4)
-
-
-
PQ208
PQG208
30.5 x 30.5
User
-
158
(32)
158
(32)
-
-
Diff
-
65
(5)
65
(5)
-
-
FT256
FTG256
17 x 17
User
-
172
(40)
190
(41)
190
(40)
-
Diff
-
68
(8)
77
(8)
77
(8)
-
FG320
FGG320
19 x 19
User
-
-
232
(56)
250
(56)
250
(56)
Diff
-
-
92
(12)
99
(12)
99
(12)
FG400
FGG400
21 x 21
User
-
-
-
304
(72)
304
(72)
Diff
-
-
-
124
(20)
124
(20)
FG484
FGG484
23 x 23
User
-
-
-
-
376
(82)
Diff
-
-
-
-
156
(21)
DS312 (v4.1) July 19, 2013
Product Specification
www.xilinx.com
4
Spartan-3E FPGA Family: Introduction and Ordering Information
Package Marking
Figure 2
provides a top marking example for Spartan-3E
FPGAs in the quad-flat packages.
Figure 3
shows the top
marking for Spartan-3E FPGAs in BGA packages except
the 132-ball chip-scale package (CP132 and CPG132). The
markings for the BGA packages are nearly identical to those
for the quad-flat packages, except that the marking is
rotated with respect to the ball A1 indicator.
Figure 4
shows
the top marking for Spartan-3E FPGAs in the CP132 and
CPG132 packages.
X-Ref Target - Figure 2
On the QFP and BGA packages, the optional numerical
Stepping Code follows the Lot Code.
The “5C” and “4I” part combinations can have a dual mark
of “5C/4I”. Devices with a single mark are only guaranteed
for the marked speed grade and temperature range. All “5C”
and “4I” part combinations use the Stepping 1 production
silicon.
Mask Revision Code
Fabrication Code
R
SPARTAN
Device Type
Package
Speed Grade
Temperature Range
TM
R
Process Technology
Date Code
Stepping Code
(optional)
Lot Code
XC3S250E
PQ208AGQ0525
D1234567A
4C
Pin P1
DS312-1_06_102905
Figure 2:
Spartan-3E QFP Package Marking Example
X-Ref Target - Figure 3
Mask Revision Code
BGA Ball A1
Device Type
Package
R
SPARTAN
R
Fabrication Code
Process Code
XC3S250E
TM
FT256AGQ0525
D1234567A
4C
Date Code
Stepping Code
(optional)
Lot Code
Speed Grade
Temperature Range
DS312-1_02_090105
Figure 3:
Spartan-3E BGA Package Marking Example
X-Ref Target - Figure 4
Ball A1
Lot Code
3S250E
F1234567-0525
PHILIPPINES
Device Type
Date Code
Temperature Range
Package
C5 = CP132
C6 = CPG132
C5AGQ
4C
Speed Grade
Process Code
Fabrication Code
DS312-1_05_032105
Mask Revision Code
Figure 4:
Spartan-3E CP132 and CPG132 Package Marking Example
As shown in the figure: This is the transformer in the CM6800PWM circuit! How should the turns ratio of this transformer be determined? 1. Assuming that the output voltage is set to 12V, PFC_VOUT=380V...
HuaDa MCU L series is an ultra-low power (LOW POWER) series of MCUs, which can achieve low power consumption of less than 0.5uA and wake-up time of 4us. Its low power performance is also remarkable in...
HOLTEK launches the new CAS Tone Detector HT9033. The new product can quickly and correctly receive CAS signals and notify the system controller to perform the call insertion function. It is suitable ...
When the WDP500-2A plane grating monochromator is used to test the emission wavelength of a high-power laser diode at different currents, the matching of the laser diode has the disadvantages of lo...[Details]
0 Introduction
With the development of my country's economy, the number of motor vehicles continues to increase. The growth of existing roads and other hardware facilities can no longer meet t...[Details]
Do you often have to add brake fluid to your car's brakes? The fact that you need to pump out the brake fluid to make sure there is no gas in the brake fluid line may not be done by the car owner h...[Details]
All electronic design engineers and scientists have performed electrical signal analysis, or signal analysis for short. Through this basic measurement, they can gain insight into signal details and...[Details]
There are three types of mobile TV: one is based on analog TV broadcasting network, another is based on mobile communication network, and the other is based on digital broadcasting network. The f...[Details]
In recent years, the market for mobile/portable devices such as smartphones and laptops has continued to grow rapidly. While these products continue to integrate more new features to enhance the ...[Details]
Due to the significant increase in electronic devices in automotive and industrial applications, the automotive and industrial markets continue to play an important role in China's electronics in...[Details]
As LEDs continue to improve in almost every aspect of performance and cost, LED lighting is being used in an increasingly wide range of applications, among which LED street lights are a focus of in...[Details]
1. Introduction
Light control circuit plays a vital role in urban street lamps or corridor lighting. With light control circuit, the lights can be automatically turned on and off according to ...[Details]
For a long time, due to the limitation of hardware conditions, the display devices of traditional small handheld devices such as PDA are usually monochrome LCD, and the user interface is very simpl...[Details]
1. Introduction
At present, most lighting equipment still uses traditional energy for lighting. Making full use of solar energy as the energy supply for lighting equipment is of great si...[Details]
Overview:
This paper introduces a method of connecting a CAN-bus network with Ethernet to form a medium-sized remote monitoring/data transmission network.
CAN (Controller Area Network) is ...[Details]
1 Introduction
Intelligent control instruments are one of the most commonly used controllers in industrial control. They are mainly aimed at a specific parameter (such as pressure, tempera...[Details]
0 Introduction
With the rise and continuous improvement of the solid-state lighting industry, light-emitting diodes (LEDs) have become an alternative lighting technology and are gr...[Details]
Many battery-powered systems require a visual indicator to show when the battery needs to be replaced. LEDs are commonly used for this purpose, but they consume at least 10mA of current. This con...[Details]
Energy Infrastructure?
京公网安备 11010802033920号
EEWORLD
