EEWORLDEEWORLDEEWORLD

Part Number

Search

SK050M3R30A3SW0511

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 50V, 20% +Tol, 20% -Tol, 3.3uF, Through Hole Mount, RADIAL LEADED, ROHS COMPLIANT
CategoryPassive components    capacitor   
File Size66KB,4 Pages
ManufacturerYAGEO
Websitehttp://www.yageo.com/
Environmental Compliance  
Download Datasheet Parametric View All

SK050M3R30A3SW0511 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 50V, 20% +Tol, 20% -Tol, 3.3uF, Through Hole Mount, RADIAL LEADED, ROHS COMPLIANT

SK050M3R30A3SW0511 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerYAGEO
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
capacitance3.3 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
dielectric materialsALUMINUM (WET)
leakage current0.00495 mA
Manufacturer's serial numberSA
Installation featuresTHROUGH HOLE MOUNT
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
Package shapeCYLINDRICAL PACKAGE
method of packingTR
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)50 V
ripple current21 mA
surface mountNO
Delta tangent0.12
Terminal shapeWIRE
YAGEO CORPORATION
ALUMINUM ELECTROLYTIC CAPACITORS
Miniature Size Aluminum
Electrolytic Capacitors
SA
[ High Ripple Current and Long load life ]
105°C Single-Ended Lead Aluminum Electrolytic Capacitors
ELECTRICAL CHARACTERISTICS
Operating Temperature : -40° ~ +105°C
-25° ~ +105°C
Working Voltage : 6.3 ~ 100V 160 ~ 450V
Rate Capacitance Range : 0.1 ~ 22000µF
Capacitance Tolerance : -20 ~ +20%
DC Leakage Current (µA) : I
0.03 CV or 4(µA) after 1 minute , I
0.04 CV +40(µA) after 1 minute
( Measurements shall be Made After a 1 Minute Charge at Rated Working Voltage )
Dissipation Factor : at 120 Hz, 25°C
DESCRIPTION
High Temperature Load Life at 105°C for
3000~8000 Hours
WV (V) : 6.3 10 16 25 35 50 63 100 160 200 250 315 400 450
D.F (%) : 28 24 20 16 14 12 10
8
20 20 20 25 25 25
For capacitor whose capacitance exceeds 1000µF. The value of D.F(%) is increased by 2% for every
addition of 1000µF.
WV (V)
:
6.3
5
12
160
3
10
4
10
200
3
16
3
8
250
4
25
2
5
350
4
35
2
4
400
6
50
2
3
450
15
63
2
3
100
2
3
Impedance : Z - 25°C / Z + 20°C
Impedance : Z - 40°C / Z + 20°C
Freq.(Hz)
Rated voltage(V)
Cap(µF)
WV (V)
50
0.75
0.80
0.80
120
1.00
1.00
1.00
300
1.35
1.23
1.25
1K
1.57
1.34
1.40
10K-
2.00
1.50
1.60
:
Impedance : Z - 25°C / Z + 20°C
6.3~100V
-47
100~470
0.47~220
Load Life : At 105°C Assured with Full Rated Maximum Ripple Current Applied
ø5~ø6=3000 hours.
ø8~ø10=5000 hours.
>ø12=8000 hours.
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200% of Initial Requirement
(c) Leakage Current : Not Exceed the Initial Requirement
Shelf Life : 1000 Hours, No Voltage Applied, at 105°C
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200 % of Initial Requirement
(c) Leakage Current : Not Exceed 200% of Initial Requirement
Dimensions : mm
Rubber Stand-off
4.0
Rubber End Seal
160~450
Temperature(°C)
Factor
~55
2.23
60
2.17
70
2.00
85
1.75
105
1.00
DIAGRAM OF DIMENSIONS
F
1.5
2.0
2.5
3.5
5.0
0.45
0.5
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Vinyl Sleeve
(P.V.C)
5.0
6.0
8.0
10.0
12.0
13.0
16.0
18.0
22.0
F 0.5
F 0.5
0.4Max.
15Min.
0.6
L
15Min.
5Min.
D 0.5
L
5Min.
D 0.5
7.5
10.0
0.8
0.8
Regarding the issue of nios, please give me some advice
The following problem occurs when using Nios: No Nios II target connection paths were located. Check connections and that a Nios II .sof is downloaded. Click refresh connection, but nothing happens? ?...
wanyi223 FPGA/CPLD
Ask: 1 warning of timing analysis warning
Question: 1 warning of timing analysis warning [table][tr][td] When doing timing analysis, only one path does not meet the requirement: -0.044 ns 99.56 MHz (period = 10.044 ns) . . . . . . . If I add ...
psd0208 FPGA/CPLD
Computer USB 3.0 interface hardware circuit design
USB is a serial bus standard for computer systems and external devices, supporting plug-and-play and hot-swap functions. It is commonly used for mobile peripherals such as USB flash drives and mice. U...
Jacktang Analogue and Mixed Signal
How to design an antenna PCB using Protel 99SE
I need help from all the experts. My tutor asked me to use Protel 99SE to design a schematic diagram of a patch antenna. What I want to ask is, do I need to draw the schematic diagram directly on this...
zhezhe0192 PCB Design
EK-LM4F120XL ADC reference voltage problem
In EK-LM4F120XL Launchpad, I use AIN0 (PE3 port) to sample 1.3V voltage, AIN1 (PE2 port) to sample 0.65V voltage, AIN8 (PE5 port) to sample 1.95V voltage, AIN9 (PE4 port) to sample 2.6V voltage. If 3....
fengzhidianzi Microcontroller MCU
Talk about the key points of antenna soldering
:) [b]The key points of soldering can be summarized as follows: [/b] 1. Before using a soldering iron (including a fire soldering iron), the surface of the soldering iron tip must be covered with a la...
xtss RF/Wirelessly

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2916  2474  103  1257  1222  59  50  3  26  25 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号