MA300RWI
Series
Wide 2:1 Input, 3W,
High 3 kVDC Isolation
DC/DC Converters
Electrical Specifications
Key Features:
•
3W Output Power
•
2:1 Input Voltage Range
•
3,000 VDC Isolation
•
32 Standard Models
•
Single & Dual Outputs
•
Compact DIP Case
•
-40°C to +85°C Operation
•
Industry Standard Pin-Out
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Parameter
Input Start Voltage
Conditions
Under Voltage Shutdown
Input Filter
Min.
5 VDC Input
12 VDC Input
24 VDC Input
48 VDC Input
5 VDC Input
12 VDC Input
24 VDC Input
48 VDC Input
(Pi)
Filter
Min.
Typ.
Max.
4.5
9.0
18.0
36.0
4.0
8.5
17.5
35.5
Max.
±2.0
±2.0
±1.0
±1.0
70
500
±5.0
±0.02
Units
VDC
VDC
Output
Parameter
Output Voltage Accuracy
Output Voltage Balance
Line Regulation
Load Regulation
Ripple & Noise (20 MHz)
Transient Recovery Time, See Note 2
Transient Response Deviation
Temperature Coefficient
Output Overload Protection
Output Short Circuit
Conditions
Dual Output, Balanced Loads
V
IN
= Min to Max
I
OUT
= 0% to 100%
See Note 1
25% Load Step Change
Typ.
±0.5
±0.3
±0.3
Units
%
%
%
%
mV P - P
µSec
%
%/°C
%
Units
VDC
M
pF
kHz
1.5 kV Isolation
Models
Available
300
±3.0
±0.01
Foldback
120
150
Continuous (Autorecovery)
Min.
3,000
1,000
90
Typ.
General
4:1 Input Range
Models
Available
Parameter
Isolation Voltage
Isolation Resistance
Isolation Capacitance
Switching Frequency
EMI Characteristics
Parameter
Radiated Emissions
Conducted Emissions
ESD
RS
EFT
Surge
CS
Conditions
60 Seconds
500 VDC
100 kHz/1.0V
Standard
EN 55022
EN 55022
EN 61000-4-2
EN 61000-4-3
EN 61000-4-4
EN 61000-4-5
EN 61000-4-6
Ambient
Case
Max.
300
See Note 3
See Note 3
Level
Class A
Class A
Criteria A; ±8 kV Air ±6 kV Contact
Criteria A; 10V/m
Criteria A; ±2 kV
Criteria A; ±1 kV
Criteria A; 10V/m
Min.
-40
Typ.
+25
Max.
+85
+100
+125
95
Units
°C
°C
°C
%
Environmental
Parameter
Operating Temperature Range
Operating Temperature Range
Storage Temperature Range
Cooling
Humidity
Physical
Case Size
Case Material
Weight
Conditions
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
T:
(781) 344-8226
F:
(781) 344-8481
E:
sales@micropowerdirect.com
W:
www.micropowerdirect.com
-50
Free Air Convection
RH, Non-condensing
1.25 x 0.80 x 0.40 Inches (31.75 x 20.32 x 10.16 mm)
Non-Conductive Black Plastic (UL94-V0)
0.45 Oz (12.8g)
Conditions
MIL HDBK 217F, 25°C, Gnd Benign
Conditions
5 VDC Input
12 VDC Input
24 VDC Input
48 VDC Input
1.5 mm From Case for 10 Sec
Min.
1.0
Min.
-0.7
-0.7
-0.7
-0.7
Typ.
Typ.
Max.
Max.
11.0
25.0
50.0
100.0
260
Units
MHours
Units
VDC
°C
Reliability Specifications
Parameter
MTBF
Absolute Maximum Ratings
Parameter
Input Voltage Surge (1 Sec)
Lead Temperature
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
www.micropowerdirect.com
Model Selection Guide
Input
Model
Number
MA305S-03RWI
MA305S-05RWI
MA305S-12RWI
MA305S-15RWI
MA305S-24RWI
MA305D-05RWI
MA305D-12RWI
MA305D-15RWI
MA312S-03RWI
MA312S-05RWI
MA312S-12RWI
MA312S-15RWI
MA312S-24RWI
MA312D-05RWI
MA312D-12RWI
MA312D-15RWI
MA324S-05RWI
MA324S-05RWI
MA324S-12RWI
MA324S-15RWI
MA324S-24RWI
MA324D-05RWI
MA324D-12RWI
MA324D-15RWI
MA348S-03RWI
MA348S-05RWI
MA348S-12RWI
MA348S-15RWI
MA348S-24RWI
MA348D-05RWI
MA348D-12RWI
MA348D-15RWI
Voltage
(VDC)
Current
(mA)
Nominal
Range
Full-Load No-Load
5
4.5 - 9.0
514
65
5
4.5 - 9.0
641
65
5
4.5 - 9.0
732
65
5
4.5 - 9.0
732
65
5
4.5 - 9.0
741
65
5
4.5 - 9.0
649
65
5
4.5 - 9.0
741
65
5
4.5 - 9.0
741
65
12
9.0 - 18.0
209
35
12
9.0 - 18.0
257
35
12
9.0 - 18.0
294
35
12
9.0 - 18.0
294
35
12
9.0 - 18.0
298
35
12
9.0 - 18.0
260
35
12
9.0 - 18.0
298
35
12
9.0 - 18.0
298
35
24
18.0 - 36.0
104
20
24
18.0 - 36.0
129
20
24
18.0 - 36.0
147
20
24
18.0 - 36.0
147
20
24
18.0 - 36.0
149
20
24
18.0 - 36.0
130
20
24
18.0 - 36.0
149
20
24
18.0 - 36.0
149
20
48
36.0 - 72.0
52
15
48
36.0 - 72.0
64
15
48
36.0 - 72.0
74
15
48
36.0 - 72.0
74
15
48
36.0 - 72.0
74
15
48
36.0 - 72.0
65
15
48
36.0 - 72.0
74
15
48
36.0 - 72.0
74
15
Voltage
(VDC)
www.micropowerdirect.com
Output
Current
(mA, Max)
Current
(mA, Min)
Efficiency
(%, Typ)
Fuse
Reflected Capacitive
Ripple
Rating
Load
Current
Slow-Blow
(µF, Max)
(mA Typ)
(mA)
3.3
5.0
12.0
15.0
24.0
±5.0
±12.0
±15.0
3.3
5.0
12.0
15.0
24.0
±5.0
±12.0
±15.0
3.3
5.0
12.0
15.0
24.0
±5.0
±12.0
±15.0
3.3
5.0
12.0
15.0
24.0
±5.0
±12.0
±15.0
600.0
500.0
250.0
200.0
125.0
±250.0
±125.0
±100.0
600.0
500.0
250.0
200.0
125.0
±250.0
±125.0
±100.0
600.0
500.0
250.0
200.0
125.0
±250.0
±125.0
±100.0
600.0
500.0
250.0
200.0
125.0
±250.0
±125.0
±100.0
0.0
0.0
0.0
0.0
0.0
±0.0
±0.0
±0.0
0.0
0.0
0.0
0.0
0.0
±0.0
±0.0
±0.0
0.0
0.0
0.0
0.0
0.0
±0.0
±0.0
±0.0
0.0
0.0
0.0
0.0
0.0
±0.0
±0.0
±0.0
77
78
82
82
81
77
81
81
79
81
85
85
84
80
84
84
79
81
85
85
84
80
84
84
79
81
85
85
84
80
84
84
100.0
100.0
100.0
100.0
100.0
100.0
100.0
100.0
30.0
30.0
30.0
30.0
30.0
30.0
30.0
30.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
680
470
330
220
100
±220
±150
±100
680
470
330
220
100
±220
±150
±100
680
470
330
220
100
±220
±150
±100
680
470
330
220
100
±220
±150
±100
1,500
1,500
1,500
1,500
1,500
1,500
1,500
1,500
600
600
600
600
600
600
600
600
300
300
300
300
300
300
300
300
150
150
150
150
150
150
150
150
Notes:
1. When measuring output ripple, it is recommended that an external 3.3
µF
ceramic capacitor be placed from the +V
OUT
pin
to the -V
OUT
pin for single output units and from each output to common for dual output units.
2. Transient recovery is measured to within a 1% error band for a load step change of 75% to 100%.
3. Operation at no-load will not damage these units.
4. An external 220
µF/100V
capacitor connected across the input pins is required to meet EN61000-4-4 and EN61000-4-5.
5. Dual output units may be connected to provide a 10, 24 or 30 VDC output. To do this, connect the load across the positive
(+V
OUT
) and negative (-V
OUT
) outputs and float the output common.
6. The converter should be connected to a low ac-impedance source. An input source with a
highly inductive impedance may affect the stability of the converter. In applications where the
converter output loading is high and input power is supplied over long lines, it may be necessary
to use a capacitor on the input to insure start-up. In this case, it is recommended that a low
ESR (ESR <1.0 at 100 kHz) capacitor be mounted close to the converter. For 5V input units a
8.2
µF
is recommended, for 12V input units, a 3.3
µF;
and for 24V & 48V units a 1.5
µF.
7. It is recommended that a fuse be used on the input of a power supply for protection. See
the table above for the correct rating.
For 1.5 kV Isolation, See
MA300-xxRW
Series Datasheet
For 4:1 Inputs, See
MA300-xxRU
Series Datasheet
Mechanical Dimensions
Derating Curve
Pin Connections
Pin
2, 3
9
11
14
16
22, 23
Single
-V
IN
No Pin
NC
+V
OUT
V
-V
OUT
V
+V
IN
Dual
-V
IN
Common
V
-V
OUT
+V
OUT
V
Common
+V
IN
NC: No Connection
MicroPower Direct
We Power Your Success - For Less!
292 Page Street Ste D Stoughton, MA 02072
•
Mechanical Notes:
•
All dimensions are typical in inches (mm)
•
Tolerance x.x = ±0.02 (±0.50)
•
Tolerance x.xx = ±0.01 (±0.25)
FAX: (781) 344-8481
•
TEL: (781) 344-8226
•
E-Mail: sales@micropowerdirect.com
京公网安备 11010802033920号
EEWORLD
