• Phase-Lock Loop Clock Distribution for Applications ranging
from 10MHz to 133MHz operating frequency
• Distributes one clock input to two banks of four outputs
• Separate output enable for each output bank
• External feedback (FBK) pin is used to synchronize the outputs
to the clock input
• Output Skew <200 ps
• Low jitter <200 ps cycle-to-cycle
• 1x, 2x, 4x output options (see table):
– IDT2308A-1 1x
– IDT2308A-2 1x, 2x
– IDT2308A-3 2x, 4x
– IDT2308A-4 2x
– IDT2308A-1H and -2H for High Drive
• No external RC network required
• Operates at 3.3V V
DD
• Available in SOIC and TSSOP packages
DESCRIPTION:
The IDT2308A is a high-speed phase-lock loop (PLL) clock multiplier. It is
designed to address high-speed clock distribution and multiplication applica-
tions. The zero delay is achieved by aligning the phase between the incoming
clock and the output clock, operable within the range of 10 to 133MHz.
The IDT2308A has two banks of four outputs each that are controlled via two
select addresses. By proper selection of input addresses, both banks can be
put in tri-state mode. In test mode, the PLL is turned off, and the input clock
directly drives the outputs for system testing purposes. In the absence of an
input clock, the IDT2308A enters power down. In this mode, the device will
draw less than 12μA for Commercial Temperature range and less than 25μA
for Industrial temperature range, and the outputs are tri-stated.
The IDT2308A is available in six unique configurations for both pre-
scaling and multiplication of the Input REF Clock. (See available options
table.)
The PLL is closed externally to provide more flexibility by allowing the user
to control the delay between the input clock and the outputs.
The IDT2308A is characterized for both Industrial and Commercial opera-
tion.
FUNCTIONAL BLOCK DIAGRAM
(-3, -4)
FBK
REF
3
CLKA2
16
1
2
PLL
2
CLKA1
14
CLKA3
15
CLKA4
S2
S1
8
9
Control
Logic
(-2, -3)
2
6
CLKB1
7
CLKB2
10
CLKB3
11
CLKB4
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES
1
c
2010
Integrated Device Technology, Inc.
MAY 2010
DSC 6587/9
IDT2308A
3.3V ZERO DELAY CLOCK MULTIPLIER
COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES
PIN CONFIGURATION
ABSOLUTE MAXIMUM RATINGS
(1)
Symbol
V
DD
Rating
Supply Voltage Range
Input Voltage Range (REF)
Input Voltage Range
(except REF)
I
IK
(V
I
< 0)
I
O
(V
O
= 0 to V
DD
)
V
DD
or GND
T
A
= 55°C
(in still air)
(3)
T
STG
Operating
Temperature
Operating
Storage Temperature Range
Commercial Temperature
Range
Industrial Temperature
Range
-40 to +85
°C
–65 to +150
0 to +70
°C
°C
Continuous Current
Maximum Power Dissipation
±100
0.7
mA
W
Input Clamp Current
Continuous Output Current
Max.
–0.5 to +4.6
–0.5 to +5.5
–0.5 to
V
DD
+0.5
–50
±50
mA
mA
Unit
V
V
V
V
I (2)
V
I
REF
CLKA1
CLKA2
V
DD
GND
CLKB1
CLKB2
S2
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
FBK
CLKA4
CLKA3
V
DD
GND
CLKB4
CLKB3
S1
SOIC/ TSSOP
TOP VIEW
Temperature
PIN DESCRIPTION
Pin Number
REF
(1)
CLKA1
(2)
CLKA2
(2)
V
DD
GND
CLKB1
(2)
CLKB2
(2)
S2
(3)
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may
cause permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those indicated in the
operational sections of this specification is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect reliability.
2. The input and output negative-voltage ratings may be exceeded if the input and output
clamp-current ratings are observed.
3. The maximum package power dissipation is calculated using a junction temperature
of 150
°
C and a board trace length of 750 mils.
Functional Description
Input Reference Clock, 5 Volt Tolerant Input
Clock Output for Bank A
Clock Output for Bank A
3.3V Supply
Ground
Clock Output for Bank B
Clock Output for Bank B
Select Input, Bit 2
Select Input, Bit 1
Clock Output for Bank B
Clock Output for Bank B
Ground
3.3V Supply
Clock Output for Bank A
Clock Output for Bank A
PLL Feedback Input
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
APPLICATIONS:
•
•
•
•
•
S1
(3)
CLKB3
(2)
CLKB4
(2)
GND
V
DD
CLKA3
(2)
CLKA4
(2)
FBK
SDRAM
Telecom
Datacom
PC Motherboards/Workstations
Critical Path Delay Designs
NOTES:
1. Weak pull down.
2. Weak pull down on all outputs.
3. Weak pull ups on these inputs.
2
IDT2308A
3.3V ZERO DELAY CLOCK MULTIPLIER
COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES
FUNCTION TABLE
(1)
SELECT INPUT DECODING
S2
L
L
H
H
NOTE:
1. H = HIGH Voltage Level
L = LOW Voltage Level
S1
L
H
L
H
CLK A
Tri-State
Driven
Driven
Driven
CLK B
Tri-State
Tri-State
Driven
Driven
Output Source
PLL
PLL
REF
PLL
PLL Shut Down
Y
N
Y
N
AVAILABLE OPTIONS FOR IDT2308A
Device
IDT2308A-1
IDT2308A-1H
IDT2308A-2
IDT2308A-2
IDT2308A-2H
IDT2308A-2H
IDT2308A-3
IDT2308A-3
IDT2308A-4
Feedback From
Bank A or Bank B
Bank A or Bank B
Bank A
Bank B
Bank A
Bank B
Bank A
Bank B
Bank A or Bank B
Bank A Frequency
Reference
Reference
Reference
2 x Reference
Reference
2 x Reference
2 x Reference
4 x Reference
2 x Reference
Bank B Frequency
Reference
Reference
Reference/2
Reference
Reference/2
Reference
Reference or
Reference
(1)
2 x Reference
2 x Reference
NOTE:
1. Output phase is indeterminant (0° or 180° from input clock).
ZERO DELAY AND SKEW CONTROL
To close the feedback loop of the IDT2308A, the FBK pin can be driven from any of the eight available output pins. The output driving the FBK pin
will be driving a total load of 7pF plus any additional load that it drives. The relative loading of this output (with respect to the remaining outputs) can adjust
the input-output delay.
For applications requiring zero input-output delay, all outputs including the one providing feedback should be equally loaded. Ensure the outputs are
Abstract : This paper introduces the use of SignalTap II embedded logic analyzer in Quartus II, a programmable logic device development tool, and gives a specific design example, detailing the specifi...
I recently started using LaunchPad, and it's not difficult to get started. One thing that impressed me deeply is that you must read the English user manual, which basically contains all the informatio...
[font=宋体][size=3]I am preparing to do a low-power project. The scope is the development board of the msp430 series. The final effect is to achieve the transmission of wireless signals from the transmi...
T2 is a 1:1 transformer. T1's 7 9 is a square wave of positive and negative 10V. 4 6 is a square wave of positive and negative 15V. The B1 terminal is a DC voltage of 0.4 to 2V. I want to get a DC vol...
Hello everyone, now I need the stm32 control program data and attitude control algorithm data for quadcopter control. I hope someone with this information can share it with me! :victory:...
introduction
1 The significance of using RTOS on MSP430
It is understandable that it is meaningless to use RTOS on MSP430. Because the hardware resources of MSP430 are limited (for exampl...[Details]
introduction
For the voltage regulator modules (VRMs) that power the latest computer central processing units (CPUs), power supply designers have historically used multiphase interleaved b...[Details]
With the rapid development of urban economy, elevators are increasingly used as a vertical transportation tool. However, elevator fault detection and maintenance, especially the role of elevator remot...[Details]
We know that microcontroller development tools generally include real-time online emulators and programmers. Among them, online emulators are very good tools, but they are also more expensive...[Details]
Instrument stepper motor
The stepper motor is an open-loop control element that converts electrical pulse signals into angular displacement or linear displacement. In the case of non...[Details]
LED is the abbreviation of light emitting diode, which is an electric light source made of semiconductor technology. The core part of LED is a chip composed of P-type semiconductor and N-type semi...[Details]
Among the many members of the single-chip microcomputer family, the MCS-51 series of single-chip microcomputers has occupied the main market of industrial measurement and control and automation eng...[Details]
From the previous section, we have learned that the timer/counter in the microcontroller can have multiple uses, so how can I make them work for the purpose I need? This requires setting the timer/...[Details]
It is well known to automotive suppliers that automakers are demanding more from their supply base. For connector suppliers, this means stricter requirements for product performance, stability and ...[Details]
The era of mobile access to the Internet has arrived, and it will rapidly change the business and infrastructure needs of mobile operators under a whole new trend of requirements. We need 4G LTE to...[Details]
Introduction
Today, as IC (integrated circuit) has developed to a super-large scale, IC design based on IP (Intellectual Property) cores and their reuse are important means to ensure the ef...[Details]
Zarlink Semiconductor has developed an ultra-low-power RF transceiver chip for pacemakers, neurostimulators, drug pumps, and other such implantable medical devices. It has high data rates, low power c...[Details]
a. Keep the battery clean, wipe off the spilled electrolyte, contaminated dirt and dust in time; keep the poles and terminal clamps clean and in good contact, and apply vaseline or butter to preven...[Details]
introduction
When it comes to the production of mobile phone lithium-ion batteries, the first thing that comes to mind is Japan's industrialized mechanical assembly line, NOKIO, MOTOLROLA's st...[Details]
1 Load Regulation
Changes in power supply load will cause changes in power supply output. When the load increases, the output decreases, and vice versa, when the load decreases, the output inc...[Details]
FPGA/CPLD
京公网安备 11010802033920号
EEWORLD
