EEWORLDEEWORLDEEWORLD

Part Number

Search

5V80013-143NLG

Description
Clock Generator, CMOS, PQCC16
CategoryThe embedded processor and controller    Microcontrollers and processors   
File Size78KB,8 Pages
ManufacturerIDT (Integrated Device Technology)
Environmental Compliance
Download Datasheet Parametric View All

5V80013-143NLG Overview

Clock Generator, CMOS, PQCC16

5V80013-143NLG Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerIDT (Integrated Device Technology)
Reach Compliance Codecompliant
JESD-30 codeS-PQCC-N16
Number of terminals16
Maximum operating temperature70 °C
Minimum operating temperature
Package body materialPLASTIC/EPOXY
encapsulated codeQCCN
Encapsulate equivalent codeLCC16,.12SQ,20
Package shapeSQUARE
Package formCHIP CARRIER
power supply1.8,3.3 V
Certification statusNot Qualified
Maximum slew rate22 mA
surface mountYES
technologyCMOS
Temperature levelCOMMERCIAL
Terminal formNO LEAD
Terminal pitch0.5 mm
Terminal locationQUAD
DATASHEET
PLL CLOCK MULTIPLIER
Description
The IDT5V80013 is the most cost effective way to generate
a high-quality, high-frequency clock output. Using
Phase-Locked Loop (PLL) techniques, the device employs
IDT’s propietary MEMs oscillator technology to produce
common output frequencies for consumer, computing, and
embedded applications.
IDT5V80013
Features
Packaged in a small form factor 16-pin QFN
Eliminates the need for an external crystal or input clock
source
Max. +50ppm error on CLK output
Typical ±75 ps short term cycle-cycle jitter
Output voltage of 3.3V
Operating voltage of 1.8V
Supports industrial temperature range
Supports output frequency on CLK up to 220MHz
Advanced, low-power CMOS process
Block Diagram
VDD
VDDO
MEMs
OScillator
PLL Clock
Synthesis
CLK
GND
IDT®
PLL CLOCK MULTIPLIER
1
IDT5V80013
REV J 022312
The past and present of the automotive bus
...
lemonade815 Automotive Electronics
Doorbell Voice Video
I took apart an old doorbell. There are 7 pins on the chip, connected to a transistor and two small capacitors, with only the words "BY-1". Some of the wires are missing. Does anyone have a picture of...
zhang_shuai2005 Creative Market
How to use operational amplifier to collect the voltage and current of the circuit
[i=s] This post was last edited by flying510 on 2015-9-8 13:39 [/i] [p=30, 2, left][size=5]I want to use MSP430 as the controller, and collect the voltage and current through the AD acquisition amplif...
flying510 Microcontroller MCU
[Silicon Labs BG22-EK4108A Bluetooth Development Review] 5. Bluetooth routines control additional pin PA0
Since I am not very familiar with Bluetooth routines, I have been trying to add new functions through GATT, but I still have no idea. I also checked the evaluation requirements and it seems that today...
kit7828 Development Kits Review Area
Building intercom system installation and debugging methods
1. Preparation before equipment installation  1. Before installing the equipment, all lines of the system must be fully checked to see if there are any disconnections or short circuits;   2. After con...
sairvee Industrial Control Electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2585  812  1198  1728  2706  53  17  25  35  55 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号