EEWORLDEEWORLDEEWORLD

Part Number

Search

50SMDJ18

Description
Surface Mount Transient Voltage Suppressors
File Size452KB,7 Pages
ManufacturerSOCAY
Websitehttp://www.socay.com
Download Datasheet View All

50SMDJ18 Overview

Surface Mount Transient Voltage Suppressors

Surface Mount Transient Voltage Suppressors (TVS)
5.0SMDJ Series
Description
The 5.0SMDJ series is designed specifically to protect sensitive electronic
equipment from voltage transients induced by lightning and other transient
voltage events.
11 To 440 V
5000W
Uni-directional
Bi-directional
Features
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
For surface mounted applications in order to optimize board space
Low leakage
Uni and Bidirectional unit
Glass passivated junction
Low inductance
Excellent clamping capability
5000W Peak power capability at 10
×
1000µs waveform Repetition
rate (duty cycle):0.01%
Fast response time: typically less than 1.0ps from 0 Volts to V
BR
min
Typical I
R
less than 5μA above 25V.
High Temperature soldering: 260°C/40 seconds at terminals
Typical maximum temperature coefficient
ΔV
BR
= 0.1%
×
V
BR
@25°C×
ΔT
Plastic package has Underwriters Laboratory Flammability 94V-0
Matte tin lead–free Plated
Halogen free and RoHS compliant
Typical failure mode is short from over-specified voltage or current
Whisker test is conducted based on JEDEC JESD201A per its table
4a and 4c
IEC-61000-4-2 ESD 15kV(Air), 8kV (Contact)
ESD protection of data lines in accordance with IEC 61000-4-2
(IEC801-2)
EFT protection of data lines in accordance with IEC 61000-4-4
(IEC801-4)
Functional Diagram
Bi-directional
Cathode
Uni-direction
Anode
Applications
TVS devices are ideal for the protection of I/O interfaces, V
CC
bus and other vulnerable circuits used in Telecom, Computer,
Industrial and Consumer electronic applications.
Maximum Ratings
(T
A
=25℃ unless otherwise noted)
Parameter
Symbol
P
PPM
I
PP
P
M(AV)
I
FSM
V
F
T
J
, T
STG
Value
5000
See Next Table
6.5
300
3.5/5.0
-55 to +150
Unit
Watts
Amps
Watt
Amps
Voltage
°C
Peak Pulse Power Dissipation with a 10/1000µs waveform (Fig.1)(Note
1), (Note 2)
Peak Pulse Current with a 10/1000µs waveform.(Note1,Fig.3)
Power Dissipation on Infinite Heat Sink at T
L
=75°C
Peak Forward Surge Current, 8.3ms Single Half Sine Wave (Note 3)
Maximum Instantaneous Forward Voltage at 25A for Unidirectional Only
(Note 4)
Operating junction and Storage Temperature Range.
Notes:
1. Non-repetitive current pulse, per Fig. 3 and derated above T
A
= 25°C per Fig. 2.
2. Mounted on 5.0mm x 5.0mm (0.03mm thick) Copper Pads to each terminal.
3. 8.3ms single half sine-wave, or equivalent square wave, Duty cycle = 4 pulses per minutes maximum.
4. V
F
< 3.5V for V
BR
< 200V and V
F
< 6.5V for V
BR
> 201V.
SOCAY Electronics Co., Ltd.
Revision September 25, 2013
www.socay.com
1/7
@ SOCAY Electronics Co., Ltd. 2013
Specifications are subject to change without notice.
Please refer to www.socay.com for current information.
Boot Sector (Boot Block) in Nor Flash
In Nor Flash, there is a concept of a boot sector (sometimes also called a boot block). This concept should only apply to Nor Flash. Because Nand Flash cannot be directly addressed, there is no Boot S...
Jacktang Microcontroller MCU
seed_2812 problem, hope it can be solved as soon as possible, thank you
When I load the included routine according to the method in the instructions, when I load F2812.GEL,Trouble Writing Target CPU memory: Cannot access memory address 0x953Trouble Writing Target CPU memo...
sunxinyu Microcontroller MCU
Experts, please tell me how to solve the following problem?
Please tell me how to solve the following problem?...
wqsax Real-time operating system RTOS
Monostable delay circuit composed of single op amp
The monostable delay circuit is composed of a single operational amplifier connected as a voltage comparator. The circuit is shown in the attached figure. It has the characteristics of simple circuit ...
rain Analog electronics
Please tell me about the problem that lwip can only connect a limited number of times as a server
I would like to ask you: My ARM is used as the server, using lwip's Raw API. I encountered the following problem: If I use tcp_listen() and use Network Assistant as the client to connect to my server,...
imsunli@163.com ARM Technology
DSP2812 download problem (what does this sentence indicate?)
Trouble Removing Breakpoint with the Action "Terminate Program Execution" at 0x3f8304: Error 0x00000008/-1066 Error during: Break Point,Cannot set/verify breakpoint at 0x003F8304...
jdzwanghao DSP and ARM Processors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 519  238  1604  2922  1028  11  5  33  59  21 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号