T110B105K060ATC datasheet, PDF

Datasheet> All Categories > Passive components> capacitor> T110B105K060ATC

T110B105K060ATC: DescriptionTantalum Capacitor, Polarized, Tantalum (dry/solid), 60V, 10% +Tol, 10% -Tol, 1uF, Through Hole Mount, AXIAL LEADED, ROHS COMPLIANT; CategoryPassive components capacitor; File Size157KB，14 Pages; ManufacturerKEMET; Websitehttp://www.kemet.com; Environmental Compliance

Download Datasheet Parametric View All

T110B105K060ATC Overview

Tantalum Capacitor, Polarized, Tantalum (dry/solid), 60V, 10% +Tol, 10% -Tol, 1uF, Through Hole Mount, AXIAL LEADED, ROHS COMPLIANT

T110B105K060ATC Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Maker	KEMET
package instruction	,
Reach Compliance Code	compliant
ECCN code	EAR99
capacitance	1 µF
Capacitor type	TANTALUM CAPACITOR
dielectric materials	TANTALUM (DRY/SOLID)
JESD-609 code	e3
leakage current	0.0005 mA
Manufacturer's serial number	T110
Installation features	THROUGH HOLE MOUNT
negative tolerance	10%
Number of terminals	2
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
Package shape	TUBULAR PACKAGE
method of packing	AMMO PACK
polarity	POLARIZED
positive tolerance	10%
Rated (DC) voltage (URdc)	60 V
surface mount	NO
Delta tangent	0.03
Terminal surface	Matte Tin (Sn)
Terminal shape	WIRE

Preview

Download Datasheet

View All

TANTALUM HERMETICALLY SEALED / AXIAL — MIL-PRF-39003

T110 SERIES — POLAR TYPE, T212 (CSR13)

KEMET standard hermetic sealed T110 Series are desirable for use in high humidi-

ty environments. They are ruggedly built, designed for miniaturized circuitry, and are

especially suited for coupling, bypass, filtering and R-C timing circuits. They exhibit

excellent stability, extremely low DC leakage current, dissipation factor, and

ESR/impedance over a wide temperature and frequency range.

Available in standard EIA capacitance values from .0047-330 µF in ±20%, ±10%, and ±5%

tolerances and working voltages from 6-125 VDC.

Higher CV values in comparable case sizes are available in KEMET T140 Series.

Refer to page 27.

Included in the following Series table is a complete listing of CSR13 qualified MIL-

PRF-39003 capacitors. KEMET is approved to manufacture the S (0.001%/k hrs.)

Exponential & D (0.001%/k hrs.) Graded failure rate levels.

KEMET is now offering low ESR limits in the T110 Series. See ESR chart on page

19. You may order the lower ESR by using Customer Specification 2864 as the last

four digits of the part number.

Effective September 30, 2005, the KEMET T110 Series is RoHS Compliant.

CAPACITOR OUTLINE DRAWINGS

1.50±.250

(38.10±6.35)

1.50±.250

(38.10±6.35)

UNINSULATED

CASE

SIZE

±0.005

±(.13)

±0.031

±(.79)

±0.010

±(.25)

INSULATED

±0.031

±(.79)

±0.002

±(.05)

MAX.

DIMENSIONS — INCHES & (MILLIMETERS)

0.125

(3.18)

0.175

(4.45)

0.279

(7.09)

0.341

(8.66)

0.250

(6.35)

0.438

(11.13)

0.650

(16.51)

0.750

(19.05)

0.135

(3.43)

0.185

(4.70)

0.289

(7.34)

0.351

(8.92)

0.286

(7.26)

0.474

(12.04)

0.686

(17.42)

0.786

(19.96)

0.020

(.51)

0.020

(.51)

0.025

(.64)

0.025

(.64)

0.422

(10.72)

0.610

(15.49)

0.822

(20.88)

0.922

(23.42)

TANTALUM

SERIES

T110, T212 (CSR13)

T111, T213 (CSR91)

T140, T242 (CSR23)

ORDERING INFORMATION*

XXX A 105 K 050 A S

SPECIFICATION

All capacitors are sleeved

unless specified.

CASE SIZE

A/B/C/D

PICOFARAD CODE

First two digits represent significant figures.

Third digit specifies number of zeros to follow.

LEAD MATERIAL

S — Standard

T – 100% Tin (T110, T140 Series only)

CAPACITANCE TOLERANCE

M — ±20%

K — ±10%

J — ±5%

FAILURE RATE**

GRADED

A — Not Applicable

B — 0.1%/k hrs.

C — 0.01%/k hrs.

D — 0.001%/k hrs.

EXPONENTIAL

M — 1%/k hrs.

P — 0.1%/k hrs.

R — 0.01%/k hrs.

S — 0.001%/k hrs.

VOLTAGE

At 85°C

**Part Number Example: T110A105K050AS (14 digits - no spaces)

*For Military Ordering Information, see page 4.

**Failure Rates apply only to military products.

MARKING INFORMATION

Marking: Unless otherwise specified by special order, standard marking of T110 Series capacitor consists of the following:

A, B, C & D CASES

+K 10%

R56 µF

100V

0312

Polarity, Manufacturer’s Identification and Capacitance Tol.

Nominal Capacitance — (µF) (“R” indicates decimal)

Voltage

Date Code (e.g.: 0312)

* For Military Marking, see page 4.

KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606 (864) 963-6300

Recommended Resources

Design and production of three-way sectional switch based on AT89C2051 microcontroller

Internal structure of MAX1908-8724-8765 chip

Application examples of LM381e

HT-81230 circuit

Microphone amplifier circuit diagram

Self-excited sawtooth wave circuit with variable frequency

【FPGA(cyclone4) 2nd issue】 Timing and simulation learning 1-Multiplier: After learning basic module programming, I always felt it was very rough, and I was not very clear about timing and simulation, so I started learning timing and simulation! The following is a simulati...; wsdymg FPGA/CPLD

EEWORLD University ---- Atmel - Achieving Infinite Possibilities: Atmel – Achieving Infinite Possibilities : https://training.eeworld.com.cn/course/511Atmel makes possibilities possible....; cuipin Talking

Are you a computer enthusiast? Come in!: Are you a computer enthusiast? You are an expert in computer, and you dominate the world; or maybe you are just silent because you are not as good as you are capable? Then you are definitely in the ri...; ds_1018 Embedded System

Is there a device called RS422 splitter?: The existing optical fiber transmits data using the RS422 protocol, and multiple terminals receive it simultaneously. Is there such a splitter? Is it possible to make the splitter yourself? I have che...; ldfsndfsa Embedded System

STM32F107VC external crystal oscillator 8M setting problem: void RCC_Configuration(void){// SystemInit();ErrorStatus HSEStartUpStatus = SUCCESS;RCC_DeInit(); //RCC system reset(for debug purpose)RCC_HSEConfig(RCC_HSE_ON); //Enable HSEHSEStartUpStatus = RCC_Wai...; wxzajx stm32/stm8

Questions about the saturation working state of transistors: When the transistor is working in the saturation region, both BC and BE junctions are turned on. If the load is heavy, will the current at the B pole be very large? Will it easily damage the transisto...; joshua03 Analog electronics

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components