SOLID TANTALUM ELECTROLYTIC CAPACITORS
F91
LOW ESR
Resin-molded Chip,
Specifications
Item
Category
Temperature Range
Capacitance Tolerance
Dissipation Factor (120Hz)
E.S.R.
(100kHz)
Performance Characteristics
--55 ~ +125
˚C
(Rated temperature : 85
˚C
)
± 20%, ±10% (at 120Hz)
Refer to the list below.
Refer to the list below.
•
After 1 minute's application of rated voltage, leakage current
at 20˚C is not more than 0.01CV or 0.5mA, whichever is greater.
•
After 1 minute's application of rated voltage, leakage current
at 85˚C is not more than 0.1CV or 5mA, whichever is greater.
•
After 1 minute's application of derated voltage, leakage current
at 125˚C is not more than 0.125CV or 6.3mA, whichever is greater.
+15% Max. (at +125
˚C
)
.
+10% Max. (at +85
˚C
)
--10% Max. (at --55
˚C
)
Leakage Current
Capacitance Change
by Temperature
Type numbering system (Example : 10V 100µF)
1
2
3
4
5
6
7
8
9
10
11
Taping code
(Refer to page 213 for details)
Case code
Capacitance tolerance
Rated Capacitance Rated voltage
Series
F 9 1 1 A 1 0 7 M C
Damp Heat
(No voltage applied)
Temperature Cycles
At 40˚C 90 ~ 95% R.H. 500 hours
Capacitance Change Within ±10% of initial value
Dissipation Factor......Initial specified value or less
Leakage Current........Initial specified value or less
--55˚C / +125˚C 30 minutes each 5 cycles
Capacitance Change Within ±5% of initial value
Dissipation Factor......Initial specified value or less
Leakage Current........Initial specified value or less
Test condition:
10 seconds reflow at 260
˚C
Capacitance Change Within ±3% of initial value
Dissipation Factor......Initial specified value or less
Leakage Current........Initial specified value or less
After application of surge in series with a 33
Ω
resistor at the rate of 30
seconds ON, seconds OFF, for 1000 sucessive test cycles at 85˚C,
capacitors meet the characteristic requirements listed below.
Capacitance Change
....
Within ±5% of initial value
Dissipation Factor
........
Initial specified value or less
Leakage Current
..........
Initial specified value or less
After 2000 hours' application of rated voltage in series with a 3
Ω
resistor
at 85
˚C
, or derated voltage in series with a 3
Ω
resistor at 125
˚C
,
capacitors meet the characteristics requirements listed below.
Capacitance Change
......
Within ±10
%
of initial value
Dissipation Factor
..........
Initial specified value or less
Leakage Current
............
Initial specified value or less
Drawing
C
•
N Case
L
H
W
1
Resistance
to Soldering Heat
Surge
∗
W
2
S
S
(mm)
L
6.0
±
0.2
7.3
±
0.2
W
1
3.2
±
0.2
4.3
±
0.2
W
2
2.2
±
0.1
2.4
±
0.1
H
2.5
±
0.2
2.8
±
0.2
S
1.3
±
0.2
1.3
±
0.2
Endurance
∗
Dimensions
Case Code
C
N
After applying the pressure load of 5N for 10
±
1 seconds
horizontally to the center of capacitor side body which has no
electrode and has been soldered
beforehand on an aluminum substrate,
5N (0.51kg
•
f)
neither exfoliation not its sign shall be
For 10±1seconds
found at the terminal electrode.
Keeping a capacitor surface-mounted on a substrate upside down
and supporting the substrate at both of the opposite bottom points
45mm apart from the center of the capacitor, the pressure load is
applied with a specified jig at the
center of the substrate so that the
20
Terminal Strength
R230
substrate may bend by 1mm as
illustrated.
Then, there shall be found no
remarkable abnormality on the
45
45
capacitor terminals.
∗
As for the surge and derated voltage at 125
˚C
, refer to page 212 for details.
Shear Test
1mm
Marking
C Case
68
10V
N Case
220
10V
Rated voltage (V)
Rated voltage (V)
Rated Capacitance (
µ
F)
Standard ratings
V
Cap.
(µF)
Code
2.5
0E
4
0G
6.3
0J
C
068
100
150
220
330
470
680
686
107
157
227
337
477
687
N
C
C
C
N
N
N
10
1A
C
C
N
N
N
Rated Volt
(V)
Rated
Capacitance
(µF)
Case
size
Part Number
Leakage
Current
(µA)
Disspation
Factor
(% @120Hz)
E.S.R.
(m
Ω
@100kHz)
2.5V
C
C•N
N
N
4V
6.3V
10V
220
470
150
220
330
470
680
100
150
220
220
330
470
68
100
150
220
330
C
N
C
C
N
N
N
C
C
C
N
N
N
C
C
N
N
N
F910E227MCC
F910E477MNC
F910G157MCC
F910G227MCC
F910G337MNC
F910G477MNC
F910G687MNC
F910J107MCC
F910J157MCC
F910J227MCC
F910J227MNC
F910J337MNC
F910J477MNC
F911A686MCC
F911A107MCC
F911A157MNC
F911A227MNC
F911A337MNC
5.5
11.8
6.0
8.8
13.2
18.8
27.2
6.3
9.5
13.9
13.9
20.8
29.6
6.8
10.0
15.0
22.0
33.0
12
12
12
12
10
16
18
10
12
14
10
14
16
8
10
10
12
18
250
100
250
250
100
100
100
250
250
250
100
100
100
300
250
100
100
100
In case of capacitance tolerance
numbering system.
±
10% type, K will be put at 9th digit of type
CAT.8100S
京公网安备 11010802033920号
EEWORLD
