Ruthenium oxide dielectric offers superior resistance
to the elements.
3) Electrodes not corroded by soldering
Thick film makes the electrodes very strong.
4) Leading the world in development and mass produc-
tion.
Since start of production in 1982 (first in the wold), this
component has established a solid reputation as a
general–purpose chip resistor.
5) ROHM resistors have approved ISO–9001 certifica-
tion.
Design and specifications are subject to change with-
out notice. Carefully check the specification sheet be-
fore using or ordering it.
!Ratings
Item
Rated power
Conditions
Power must be derated according to the power derating curve in
Figure 1 when ambient temperature exceeds 70
°C
.
100
80
60
40
20
0
Specifications
0.125W (1 / 8W)
[0.100W (1 / 10W)]
∗
at 70°C
POWER LOAD (%)
– 55
0
70
100
155
AMBIENT TEMPERATURE (°C)
Fig.1
Rated voltage
The voltage rating is calculated by the following equation. If the value
obtained exceeds the maximum operating voltage, the voltage rating
is equal to the maximum operating voltage.
E: Rated voltage (V)
E = P× R
P: Rated power (W)
R: Nominal resistance (Ω)
Nominal resistance
Operating temperature
* At power rating of 0.1W, maximum overload voltage and maximum intermittent overload voltage are 300V.
Max. operating voltage
150V
200V
(300V)
∗
Max. overload voltage
Max. intermittent overload voltage 200V
(300V)
∗
See Table 1.
– 55
°C
to + 155
°C
MCR10
Resistors
Jumper type
Resistance
Rated current
Peak current
Max. 50mΩ
2A
10A
J ( ± 5%)
Table 1
Resistance tolerance
F ( ± 1%)
Resistance range
(Ω)
10
≤
R
≤
2.2M (E24,96)
1.0
≤
R
<
2.2
2.2
≤
R
<
10
10
≤
R
<
10M
(E24)
(E24)
(E24)
Resistance temperature coefficient
(ppm /
°C)
± 100
500 ± 350
± 500
± 200
Operating temperature – 55°C to + 155°C
!Before
using components in circuits where they will be exposed to transients such as pulse loads (short–duration, high– level loads), be certain to evaluate the
component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that
is greater than its rated voltage.
MCR10
Resistors
!Characteristics
Characteristics
DC resistance
Resistance temperature
characteristics
Short time overload
±
(2.0% + 0.1Ω)
Specifications
Chip resistance
Jumper type
F:
±
1%
J:
±
5%
Max. 50mΩ
Test method
JIS C 5202 5.1
Applied voltage: A
JIS C 5202 5.2
Test conditions: + 25 / – 55 / + 25 / + 125°C
JIS C 5202 5.5
Rated voltage (current):
×
2.5, 5s.
Maximum overload voltage: 200V
JIS C 5202 5.6
Test voltage: 100V, 1min.
Assembled state
Metal block
observation
point A
Insulation plate
See Table 1.
Max. 50mΩ
Min. 1,000MΩ between terminal and board
Insulation resistance
Test resistor
Metal plate
Observation Insulation
sheath
R 0.5
point B
Spring-loaded
pressure
Withstand voltage
Do not damage insulation or cause a short circuit.
±
(5.0% + 0.1Ω)
JIS C 5202 5.7
Test voltage: 500V
JIS C 5202 5.8
Rated voltage (current):
×
2.5
(1s: ON – 25s: OFF)
×
10,000cyc.
JIS C 5202 6.1
JIS C 5202 6.4
Soldering conditions: 260
±
5°C
Soldering time: 10
±
1s.
JIS C 5202 6.5
Rosin methanol: (25%WT)
Soldering conditions: 235
±
5°C
Soldering time: 2.0
±
0.5s.
JIS C 5202 7.2
155°C
Test time: 1,000 to 1,048 hrs.
JIS C 5202 7.10
Rated voltage (current), 70°C
1.5h: ON – 0.5h: OFF
Test time: 1,000 to 1,048 hrs.
JIS C 5202 7.9
Rated voltage (current), 60°C, 90%RH
1.5h: ON – 0.5h: OFF
Test time: 1,000 to 1,048 hrs.
JIS C 5202 7.5
85°C, 85%RH
Test time: 1,000 to 1,048 hrs.
JIS C 5202 7.4
Test temperature: – 55°C to + 125°C 100cyc.
JIS C 5202 6.9
Room temperature, static immersion, 1 min.
Solvent: Isopropyl alcohol
Intermittent overload
Terminal strength
(against bending of circuit board)
Resistance to soldering heat
Max. 50mΩ
±
(1.0% + 0.05Ω)
Max. 50mΩ
There must be no mechanical damage.
±
(1.0% + 0.05Ω)
Max. 50mΩ
Outside must not be noticeably damaged.
95% of terminal surface must be covered by
new soldering, and there must be
no soldering corrosion.
Solderability
Resistance to dry heat
±
(3.0% + 0.1Ω)
Max. 100mΩ
Endurance
(under load in damp environment)
±
(3.0% + 0.1Ω)
Max. 100mΩ
Endurance
(steady state)
±
(3.0% + 0.1Ω)
Max. 100mΩ
Resistance to humidity
(steady state)
±
(3.0% + 0.1Ω)
Max. 100mΩ
Temperature cycling
±
(1.0% + 0.05Ω)
Max. 50mΩ
Resistance to solvents
Max. 50mΩ
±
(0.5% + 0.05Ω)
Markings must not be dissolved away.
MCR10
Resistors
!External
dimensions
(Units: mm)
0.4 ± 0.2
No.
0.4 ± 0.2
2.0 ± 0.1
0.55 ± 0.1
Material
Thick dielectric glaze of ruthenium
(only silver used for jumper)
Thick film of palladium-silver for primary electrode
Nickel-coated secondary electrode
External electrode coated with tin and lead
Alumina substrate
1.25 ± 0.1
Overcoating
!Packaging
Reel
Taping
P
0
P
2
P
1
φD
0
E
F
B
0
08
06
04
02
02
04
06
08
W
A
B
D
A
0
Heat crimp cover/Tape
Thick paper (Underside paper tape) Chip resistor Square punchout hole
In Linux, each file has a dentry and an inode. These two structures are data structures created by VFS in memory based on the information on the specific file system disk. Is this correct? When we mou...
[font=Tahoma][font=Simsun][color=#000000][/color][/font]Hello everyone, I am doing maintenance work on industrial control and need to burn programs into TMS320F2808PZS. But I am new to this and I am i...
There are products from different brands such as S3C, TI, and Freescale on the market, but which one is more suitable for consumer electronics products? Let me analyze it for you. S3C's development bo...
[i=s]This post was last edited by taotieren on 2019-12-18 15:33[/i]KiCad RF Tool Python Script:https://gitee.com/KiCAD-CN/kicad-cn-forum/blob/master/zh_CN/KiCad_plugin.md#kicad-%E5%B0%84%E9%A2%91%E5%B...
[table=98%][tr][td][b]Introduction[/b] At present, Ethernet 802.3 protocol and TCP/IP protocol are the preferred protocols for embedded systems to access the Internet. The core idea of Ethernet is tha...
Shanghai company recruits the following positions. If you are interested, please send your resume to [email=xinjihr_cn@126.com]xinjihr_cn@126.com[/email], or msn: [email=mouhuitou@hotmail.com]mouhuito...
At present, the development of wireless power supply technology for electric vehicles (EVs) is becoming more and more active. In 2012, Volvo of Sweden established Volvo Technology Japan in Tokyo as...[Details]
With the promotion of the construction of intelligent communities in the country, anti-theft systems have become essential equipment for intelligent communities. Especially in recent years, the urg...[Details]
This article discusses how to wake up a touch-sensitive device such as a tablet without touching the device, using basic gesture recognition and novel proximity sensors. The article discusses the p...[Details]
Automotive applications are particularly sensitive to EMI events, which are unavoidable in a noisy electrical environment consisting of a central battery, bundled wiring harnesses, various inductiv...[Details]
In order to highlight the concept of "energy saving and environmental protection" of intelligent buildings, solar street lights are designed for intelligent communities. The inclination and capacit...[Details]
0 Introduction
With the development of society, people pay more and more attention to security work. Monitoring products have been used in various fields instead of being used only in importan...[Details]
Although it is relatively easy to check the stability of a simple amplifier at lower frequencies, it may be much more difficult to evaluate the stability of a more complex circuit. This artic...[Details]
The automotive lighting and signal control system is responsible for controlling the vehicle's lighting, signal lights, electric horns, reversing and brake buzzers. Traditional automotive lighting...[Details]
The typical fault troubleshooting listed below is for reference of maintenance personnel.
When the computer is turned on, the indicator light is off and there is no screen display
Mainte...[Details]
In recent years, with the rapid development of the information industry, dot matrix LED display screens have been widely used in various advertising and information display systems such as the fina...[Details]
We know that the inverter consists of two parts: the main circuit and the control circuit. Due to the nonlinearity of the main circuit (switching action), the inverter itself is a source of harmoni...[Details]
Today, the value of electronic components in cars accounts for 15-20% of the total vehicle. In the future, this proportion may be as high as 30-40% as more safety electronics, fuel consumption and ...[Details]
The TPS92210 is a single-stage LED lighting pulse width modulation (PWM) controller. The TRIAC dimmable solution not only regulates the LED current, but also achieves a power factor close to 1. The...[Details]
With the continuous advancement of various technologies in the field of measurement and control, the baseband subsystem of general measurement and control equipment has entered the fourth generation o...[Details]
Abstract: Based on the ZigBee parking lot SMS car search system, the location of the vehicle in the parking lot is sent to the owner through SMS, which is convenient for the owner to quickly find ...[Details]
Linux and Android
京公网安备 11010802033920号
EEWORLD
