EEWORLDEEWORLDEEWORLD

Part Number

Search

X9315USIZ

Description
Digitally Controlled Potentiometer (XDCP™); MSOP8, SOIC8; Temp Range: See Datasheet
CategoryAnalog mixed-signal IC    converter   
File Size710KB,16 Pages
ManufacturerRenesas Electronics Corporation
Websitehttps://www.renesas.com/
Download Datasheet Parametric View All

X9315USIZ Online Shopping

Suppliers Part Number Price MOQ In stock  
X9315USIZ - - View Buy Now

X9315USIZ Overview

Digitally Controlled Potentiometer (XDCP™); MSOP8, SOIC8; Temp Range: See Datasheet

X9315USIZ Parametric

Parameter NameAttribute value
Brand NameIntersil
MakerRenesas Electronics Corporation
Parts packaging codeMSOP, SOIC
package instructionSOP, SOP8,.25
Contacts8, 8
Reach Compliance Codecompliant
ECCN codeEAR99
Factory Lead Time11 weeks
Other featuresNONVOLATILE MEMORY
control interfaceINCREMENT/DECREMENT
Converter typeDIGITAL POTENTIOMETER
JESD-30 codeR-PDSO-G8
JESD-609 codee3
length4.9 mm
Humidity sensitivity level1
Number of functions1
Number of positions32
Number of terminals8
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
Package body materialPLASTIC/EPOXY
encapsulated codeSOP
Encapsulate equivalent codeSOP8,.25
Package shapeRECTANGULAR
Package formSMALL OUTLINE
Peak Reflow Temperature (Celsius)260
power supply5 V
Certification statusNot Qualified
resistance lawLINEAR
Maximum resistor tolerance20%
Maximum resistor terminal voltage5 V
Minimum resistor terminal voltage
Maximum seat height1.75 mm
Nominal supply voltage5 V
surface mountYES
technologyCMOS
Nominal temperature coefficient300 ppm/°C
Temperature levelINDUSTRIAL
Terminal surfaceMatte Tin (Sn) - annealed
Terminal formGULL WING
Terminal pitch1.27 mm
Terminal locationDUAL
Maximum time at peak reflow temperature30
Nominal total resistance50000 Ω
width3.9 mm
DATASHEET
X9315
Low Noise, Low Power, 32 Taps Digitally Controlled Potentiometer
(XDCP™)
The Intersil X9315 is a digitally controlled potentiometer
(XDCP). The device consists of a resistor array, wiper
switches, a control section, and nonvolatile memory. The
wiper position is controlled by a 3-wire interface.
The potentiometer is implemented by a resistor array
composed of 31 resistive elements and a wiper switching
network. Between each element and at either end are tap
points accessible to the wiper terminal. The position of the
wiper element is controlled by the CS, U/D, and INC inputs.
The position of the wiper can be stored in nonvolatile
memory and then be recalled upon a subsequent power-up
operation.
The device can be used as a three-terminal potentiometer or
as a two-terminal variable resistor in a wide variety of
applications including:
• Control
• Parameter Adjustments
• Signal Processing
FN8179
Rev.2.00
December 21, 2009
Features
• Solid-state potentiometer
• 3-wire serial interface
• 32 wiper tap points
- Wiper position stored in nonvolatile memory and
recalled on power-up
• 31 resistive elements
- Temperature compensated
- End to end resistance range ± 20%
- Terminal voltage, 0 to V
CC
• Low power CMOS
- V
CC
= 2.7V or 5V
- Active current, 80/400µA max.
- Standby current, 5µA max.
• High reliability
- Endurance, 100,000 data changes per bit
- Register data retention, 100 years
• R
TOTAL
values = 10k, 50k, 100k
• Packages
- 8 Ld SOIC, MSOP and PDIP
• Pb-free available (RoHS compliant)
Block Diagram
U/D
INC
CS
R
H
/V
H
Control
and
Memory
R
W
/V
W
R
L
/V
L
Store and
Recall
Control
Circuitry
5-Bit
Nonvolatile
Memory
5-Bit
Up/Down
Counter
31
30
29
28
One
of
Thirty
Two
Decoder
2
V
SS
(Ground)
General
V
CC
V
SS
1
0
R
L
/V
L
R
W
/V
W
Detailed
R
H
/V
H
V
CC
(Supply Voltage)
Up/Down
(U/D)
Increment
(INC)
Device Select
(CS)
Transfer
Gates
Resistor
Array
FN8179 Rev.2.00
December 21, 2009
Page 1 of 16
LM3S811 Learning Experience
When I learned that I was lucky enough to receive the LM3s811 from eeworld, I was so excited that I couldn't express it in words. Finally, on the morning of the third day after the board was sent, a t...
heningbo Microcontroller MCU
Can you guys help me figure out what this chip is?
A chip on the circuit board, marked as U3 on the PCB, and written as 2813 on the chip, what kind of chip is this? Measured 21,31 (red test lead connected to 2,3) the voltage is 0.555V. Could you pleas...
hfutdsplab Analogue and Mixed Signal
Maxpro X6 PLUS Smart Charger Circuit Diagram
Maxpro X6 PLUS Smart Charger Circuit Diagram...
zhdming123 Automotive Electronics
TI MCU Classification
Let's systematically sort out TI's mainstream MCU series in recent years.According to the information currently given on TI's official website, TI's MCUs can be roughly divided into the following thre...
灞波儿奔 RF/Wirelessly
Wince5.0 Remote Tool cannot connect
[size=11px]I have a 2410 development board. I used Activesync to connect the PC and the development board. The connection was normal. The PC could also display the mobile device and the folders on the...
quansheng Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 939  2469  2562  903  2475  19  50  52  37  48 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号