Min. 1,000 MΩ (at 500V DC) Measurement at same location as “Breakdown voltage” section.
1,000 Vrms for 1 min. (Detection current: 10mA)
5,000 Vrms for 1 min. (Detection current: 10mA)
Max. 55°C
131°F
[with nominal coil voltage and at 16A contact carrying current (resistance method) at 20°C
68°F]
10,000 V
Max. 15ms (excluding contact bounce time)
Max. 5ms (excluding contact bounce time, without diode)
100 m/s
2
(Half-wave pulse of sine wave: 11ms; detection time: 10µs)
1,000 m/s
2
(Half-wave pulse of sine wave: 6ms)
10 to 55Hz at double amplitude of 1.5mm (Detection time: 10µs)
(Only the N.C. side of 1 Form C is 0.8mm)
10 to 55Hz at double amplitude of 1.5mm
Min. 10
7
N.O.: Min. 10
5
, N.C.: Min. 5
×
10
4
Ambient temperature: –40°C to +85°C
–40°F to +185°F
(Class B),
Humidity: 5 to 85% R.H. (Not freezing and condensing at low temperature)
20 times/min. (at nominal switching capacity)
Approx. 12 g
.42 oz
Rating
Mechanical
characteristics
Expected life
Destructive
Mechanical (at 180 times/min.)
Electrical (at 20 times/min.)*
3
Conditions for operation, transport and storage*
4,
*
5
Max. operating speed
Conditions
Unit weight
Notes: *1. This value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the
actual load.
*2. Wave is standard shock voltage of
±1.2 ×
50µs according to JEC-212-1981.
*3. In order to obtain the full rated life cycles, the relay should be properly vented by removing the vent nib. More detail, please look at caution for NOTES.
*4. Class F type is ambient temperature 105°C
221°F.
*5. The upper limit of the ambient temperature is the maximum temperature that can satisfy the coil temperature rise value. Refer to Usage, transport and storage
conditions in NOTES.
*Please note that some of the specifications listed above may not comply with overseas standards.
Panasonic Corporation Automation Controls Business Division
The circuit is a reference to the circuit on the pdf, it is very simple. The only difference is that the capacitor connected to the crystal oscillator is a fixed 15pF. It can be read and written throu...
On February 27, 2020, the PCIe official organization released the first version of the PCIe Gen5 Phy Test Spec V0.3, which clearly stated that the PCIe Gen5 System transmitter test will no longer use ...
[font=微软雅黑] [size=3] With the development of single-chip microcomputers, more and more people have begun to pay attention to the application architecture issue. However, few people have specifically t...
With the promotion of the construction of intelligent communities in the country, anti-theft systems have become essential equipment for intelligent communities. Especially in recent years, the urg...[Details]
When choosing a laptop battery, you should consider several factors, such as power, appearance, and quality.
Regarding power, we often see that a manufacturer uses values such as the number ...[Details]
Product series: PB-B-RS232/485 interface (hereinafter sometimes referred to as "interface") is a product in the PROFIBUS bus bridge series.
The main purpose of the bridge series ...[Details]
1 Introduction
Building Automation System (BAS) is a distributed monitoring system (DCS) designed according to distributed information and control theory. It is the result of the mutual de...[Details]
1 Introduction
With the development of control, computer, communication, network technology, etc., a new control technology, namely fieldbus, has emerged in the field of industrial control...[Details]
The concept of state machine
State machine is an important concept in software programming. More important than this concept is its flexible application. In a clear and efficient program, ther...[Details]
We know that the inverter consists of two parts: the main circuit and the control circuit. Due to the nonlinearity of the main circuit (switching action), the inverter itself is a source of harmoni...[Details]
Introduction
In industrial control, speed measurement is often required. Generally, a contact tachometer is used. This tachometer must be placed against the center of the shaft to measure. It...[Details]
0 Introduction
In order to improve the automation control of shortwave transmitters, so that they can automatically process from far to near, the technicians here use the ICS system to complete the ...[Details]
1 Embedded Systems
Embedded System refers to a collection of computer hardware and software with specific functions or purposes, which is divided into embedded software system and embe...[Details]
Introduction
my country's rapid economic growth is mainly due to the development of manufacturing and the acceleration of urbanization. However, urbanization cannot be achieved at the expense ...[Details]
introduction
The Steyr diesel engine produced by Weifang Diesel Engine Factory has huge power and is one of the main power models widely used in China's heavy machinery and large trucks. In ...[Details]
Today's automotive application developers face numerous design challenges as modern cars add more electronic functionality, while the need for lower power consumption and smaller printed circuit bo...[Details]
1. Basic principles of organic/polymer solar cells
The basic principle of organic/polymer solar cells is to use the photovoltaic effect generated by light incident on the heterojunction of sem...[Details]
Improving the coordination of material handling and internal transportation between departments in modern factories is an important measure to achieve full automation of production. Traditional mat...[Details]
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
