Asynchronous operation for compatibility with industry-
standard 512K x 8 SRAMs
CMOS compatible inputs and output levels, three-state
bidirectional data bus
- I/O Voltage 3.3 volts, 1.8 volt core
Radiation performance
- Intrinsic total-dose: 300 Krad(Si)
- SEL Immune >100 MeV-cm
2
/mg
- LET
th
(0.25): 53.0 MeV-cm
2
/mg
- Memory Cell Saturated Cross Section 1.67E-7cm
2
/bit
- Neutron Fluence: 3.0E14n/cm
2
- Dose Rate
- Upset 1.0E9 rad(Si)/sec
- Latchup 1.0E11 rad(Si)/sec
Packaging options:
- 68-lead ceramic quad flatpack (20.238 grams with lead
frame)
Standard Microcircuit Drawing 5962-04227
- QML compliant part
INTRODUCTION
The UT8CR512K32 is a high-performance CMOS static RAM
multi-chip module (MCM), organized as four individual
524,288 words by 8 bit SRAMs with common output enable.
Easy memory expansion is provided by active LOW chip
enables (E), an active LOW output enable (G), and three-state
drivers. This device has a power-down feature that reduces
power consumption by more than 90% when deselected.
Writing to each memory is accomplished by taking the
corresponding chip enable (E) input LOW and write enable (W)
input LOW. Data on the I/O pins is then written into the location
specified on the address pins (A
0
through A
18
). Reading from
the device is accomplished by taking the chip enable (E) and
output enable (G) LOW while forcing write enable (W) HIGH.
Under these conditions, the contents of the memory location
specified by the address pins will appear on the I/O pins.
The input/output pins are placed in a high impedance state when
the device is deselected (E HIGH), the outputs are disabled (G
HIGH), or during a write operation (E LOW and W LOW).
Perform 8, 16, 24 or 32 bit accesses by making W along with E
a common input to any combination of the discrete memory die.
E3
A(18:0)
G
W3
E2
W2
E1
W1
W0
E0
512K x 8
512K x 8
512K x 8
512K x 8
DQ(31:24)
or
DQ3(7:0)
DQ(23:16)
or
DQ2(7:0)
DQ(15:8)
or
DQ1(7:0)
DQ(7:0)
or
DQ0(7:0)
Figure 1. UT8CR512K32 SRAM Block Diagram
1
V
DD1
A0
A1
A2
A3
A4
A5
E2
V
SS
E3
W0
A6
A7
A8
A9
A10
V
DD2
DEVICE OPERATION
DQ0(2)
DQ1(2)
DQ2(2)
DQ3(2)
DQ4(2)
DQ5(2)
DQ6(2)
DQ7(2)
V
SS
DQ0(3)
DQ1(3)
DQ2(3)
DQ3(3)
DQ4(3)
DQ5(3)
DQ6(3)
DQ7(3)
DQ0(0)
DQ1(0)
DQ2(0)
DQ3(0)
DQ4(0)
DQ5(0)
DQ6(0)
DQ7(0)
V
SS
DQ0(1)
DQ1(1)
DQ2(1)
DQ3(1)
DQ4(1)
DQ5(1)
DQ6(1)
DQ7(1)
68 67 66 65 64 63 62 61 60 59 58 57 56 555453 52
1
51
2
50
3
49
4
48
5
47
Top View
6
46
7
45
8
44
9
43
10
42
11
41
12
40
13
39
14
38
15
37
16
36
17
35
1819 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34
V
DD2
A11
A12
A13
A14
A15
A16
E0
G
E1
A17
W1
W2
W3
A18
V
DD1
V
SS
Each die in the UT8CR512K32 has three control inputs called
Enable (E), Write Enable (W), and Output Enable (G); 19
address inputs, A(18:0); and eight bidirectional data lines,
DQ(7:0). The device enable (E) controls device selection,
active, and standby modes. Asserting E enables the device,
causes I
DD
to rise to its active value, and decodes the 19 address
inputs to each memory die by selecting the 2,048,000 byte of
memory. W controls read and write operations. During a read
cycle, G must be asserted to enable the outputs.
Table 1. Device Operation Truth Table
G
X
X
1
0
W
X
0
1
1
E
1
0
0
0
I/O Mode
3-state
Data in
3-state
Data out
Mode
Standby
Write
Read
2
Read
Figure 2. 17ns SRAM Pinout 68)
PIN NAMES
A(18:0)
DQ(7:0)
E
W
G
V
DD1
V
DD2
V
SS
Address
Data Input/Output
Enable
Write Enable
Output Enable
Power (1.8V)
Power (3.3V)
Ground
Notes:
1. “X” is defined as a “don’t care” condition.
2. Device active; outputs disabled.
READ CYCLE
A combination of W greater than V
IH
(min) with E and G less
than V
IL
(max) defines a read cycle. Read access time is
measured from the latter of device enable, output enable, or valid
address to valid data output.
SRAM read Cycle 1, the Address Access is initiated by a change
in address inputs while the chip is enabled with G asserted and
W deasserted. Valid data appears on data outputs DQn(7:0) after
the specified t
AVQV
is satisfied. Outputs remain active
throughout the entire cycle. As long as device enable and output
enable are active, the address inputs may change at a rate equal
to the minimum read cycle time (t
AVAV
).
SRAM read Cycle 2, the Chip Enable-controlled Access is
initiated by E going active while G remains asserted, W remains
deasserted, and the addresses remain stable for the entire cycle.
After the specified t
ETQV
is satisfied, the eight-bit word
addressed by A(18:0) is accessed and appears at the data outputs
DQn(7:0).
SRAM read Cycle 3, the Output Enable-controlled Access is
initiated by G going active while E is asserted, W is deasserted,
and the addresses are stable. Read access time is t
GLQV
unless
t
AVQV
or t
ETQV
have not been satisfied.
2
WRITE CYCLE
A combination of W less than V
IL
(max) and E less than
V
IL
(max) defines a write cycle. The state of G is a “don’t care”
for a write cycle. The outputs are placed in the high-impedance
state when either G is greater than V
IH
(min), or when W is less
than V
IL
(max).
Write Cycle 1, the Write Enable-controlled Access is defined
by a write terminated by W going high, with E still active. The
write pulse width is defined by t
WLWH
when the write is initiated
by W, and by t
ETWH
when the write is initiated by E. Unless the
outputs have been previously placed in the high-impedance state
by G, the user must wait t
WLQZ
before applying data to the eight
bidirectional pins DQn(7:0) to avoid bus contention.
Write Cycle 2, the Chip Enable-controlled Access is defined by
a write terminated by the former of E or W going inactive. The
write pulse width is defined by t
WLEF
when the write is initiated
by W, and by t
ETEF
when the write is initiated by the E going
active. For the W initiated write, unless the outputs have been
previously placed in the high-impedance state by G, the user
must wait t
WLQZ
before applying data to the eight bidirectional
pins DQn (7:0) to avoid bus contention.
The UT8CR512K32 SRAM incorporates special design and
layout features which allows operation in a limited radiation
environment.
Table 2. Radiation Hardness
Design Specifications
1
Total Dose
Heavy Ion
Error Rate
2
300K
8.9x10
-10
rad(Si)
Errors/Bit-Day
Notes:
1. The SRAM is immune to latchup to particles >100MeV-cm
2
/mg.
2. 10% worst case particle environment, Geosynchronous orbit, 100 mils of
Aluminum.
Supply Sequencing
No supply voltage sequencing is required between V
DD1
and
V
DD2
.
RADIATION HARDNESS
3
ABSOLUTE MAXIMUM RATINGS
1
(Referenced to V
SS
)
SYMBOL
V
DD1
V
DD2
V
I/O
T
STG
P
D
T
J
Θ
JC
I
I
PARAMETER
DC supply voltage
DC supply voltage
Voltage on any pin
Storage temperature
Maximum power dissipation
Maximum junction temperature
2
Thermal resistance, junction-to-case
3
DC input current
LIMITS
-0.3 to 2.0V
-0.3 to 3.8V
-0.3 to 3.8V
-65 to +150°C
1.2W
+150°C
5°C/W
±
5 mA
Notes:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, and functional operation of the device at
these or any other conditions beyond limits indicated in the operational sections of this specification is not recommended. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability and performance.
2. Maximum junction temperature may be increased to +175°C during burn-in and steady-static life.
3. Test per MIL-STD-883, Method 1012.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD1
V
DD2
T
C
V
IN
PARAMETER
Positive supply voltage
Positive supply voltage
Case temperature range
DC input voltage
LIMITS
1.7 to 1.9V
3.0 to 3.6V
(C) Screening: -55 to +125°C
(W) Screening: -40 to +125°C
0V to V
DD2
4
DC ELECTRICAL CHARACTERISTICS (Pre and Post-Radiation)*
(-55°C to +125°C for (C) screening and -40°C to 125°C for (W) screening)
SYMBOL
V
IH
V
IL
V
OL1
V
OH1
C
IN1
C
IO1
I
IN
I
OZ
PARAMETER
High-level input voltage
Low-level input voltage
Low-level output voltage
High-level output voltage
Input capacitance
Bidirectional I/O capacitance
Input leakage current
Three-state output leakage
current
Short-circuit output current
I
OL
= 8mA,V
DD2
=V
DD2
(min)
I
OH
= -4mA,V
DD2
=V
DD2
(min)
ƒ
= 1MHz @ 0V
ƒ
= 1MHz @ 0V
V
IN
= V
DD2
and V
SS
V
O
= V
DD2
and V
SS,
V
DD2
= V
DD2
(max)
G = V
DD2
(max)
V
DD2
= V
DD2
(max), V
O
= V
DD2
V
DD2
= V
DD2
(max), V
O
= V
SS
Inputs : V
IL
= V
SS
+ 0.2V
V
IH
= V
DD2
- 0.2V, I
OUT
= 0
V
DD1
= V
DD1
(max), V
DD2
= V
DD2
(max)
Inputs : V
IL
= V
SS
+ 0.2V,
V
IH
= V
DD2
- 0.2V, I
OUT
= 0
V
DD1
= V
DD1
(max), V
DD2
= V
DD2
(max)
Inputs : V
IL
= V
SS
+ 0.2V
V
IH
= V
DD2
- 0.2V, I
OUT
= 0
V
DD1
= V
DD1
(max), V
DD2
= V
DD2
(max)
Inputs : V
IL
= V
SS
+ 0.2V,
V
IH
= V
DD2
- 0.2V, I
OUT
= 0
V
DD1
= V
DD1
(max), V
DD2
= V
DD2
(max)
CMOS inputs , I
OUT
= 0
E = V
DD2
-0.2
V
DD1
= V
DD1
(max), V
DD2
= V
DD2
(max)
CMOS inputs , I
OUT
= 0
E = V
DD2
- 0.2
V
DD1
= V
DD1
(max), V
DD2
= V
DD2
(max)
100
mA
-2
-2
.8*V
DD2
44
21
2
2
CONDITION
MIN
.7*V
DD2
.3*V
DD2
.2*V
DD2
MAX
UNIT
V
V
V
V
pF
pF
µA
µA
I
OS2, 3
-100
+100
mA
I
DD1
(OP
1
)
Supply current operating
@ 1MHz
40
mA
I
DD1
(OP
2
)
Supply current operating
@58.8MHz
I
DD2
(OP
1
)
Supply current operating
@ 1MHz
.35
mA
I
DD2
(OP
2
)
Supply current operating
@58.8MHz
11
mA
I
DD1
(SB)
4
I
DD2
(SB)
4
I
DD1
(SB)
4
I
DD2
(SB)
4
Supply current standby @
0Hz
35
5
35
5
mΑ
µA
mΑ
µA
Supply current standby
A(18:0) @ 58.8MHz
Notes:
* Post-radiation performance guaranteed at 25°C per MIL-STD-883 Method 1019 at 1.0E5 rad(Si).
1. Measured only for initial qualification and after process or design changes that could affect input/output capacitance.
2. Supplied as a design limit but not guaranteed or tested.
3. Not more than one output may be shorted at a time for maximum duration of one second.
Introduction Although voltage measurement alone has been used in many portable products to estimate the remaining battery charge, this approach can have errors as high as 50%. The relationship between...
The original program of the servo motor controlled by the single-chip microcomputer is as follows: ORG 00H SJMP MAIN ORG 0008H LJMP TOSUB ORG 001BH LJMP T1SUB MAIN: MOV TMOD,#22H ;Working mode 2 (8-bi...
I would like to ask: In terms of hardware, the LCD backlight power supply has been turned on, that is, the LCD backlight is on after power-on. How can I make the LCD enter power saving mode during dis...
The intelligent driving community has its own rhythm. Some are busy pushing new versions and focusing on R&D, others are busy with publicity and promotion, and still others are immersed in mass pro...[Details]
1. Equipment Overview
Shell-and-tube heat exchangers are a common heat exchange device used in chemical evaporation and heating equipment. Currently, the tubesheets of shell-and-tube heat exch...[Details]
How do you know if a machine is operating properly? The answer: by leveraging deep learning to detect anomalies in routine vibration data from industrial machines. Anomaly detection has many uses, ...[Details]
The problem of dynamic sealing of equipment always exists with the operation of the equipment. Today, we have specially sorted out the various commonly used sealing forms, usage scope and character...[Details]
ISP devices, such as field programmable devices (FPGAs and CPLDs), do not require a programmer. Using programming kits provided by the device manufacturer, they employ a top-down modular design app...[Details]
New energy vehicles are increasingly popular with consumers due to policies and energy conservation. Once you've purchased your vehicle, maintenance is essential. However, due to the different powe...[Details]
As time goes by, people are increasingly concerned about their own and their families' health. However, existing monitoring devices for individual vital signs have struggled to gain market share du...[Details]
1 Source of creativity
With the further development of electronic technology, electronic pets have gradually entered people's family life. At present, there are two main categories of relative...[Details]
Since its invention in the mid-1940s, the microwave oven has evolved from a humble beginning to commercial use, entering homes in the 1960s and rapidly gaining popularity. Its basic functionality a...[Details]
The digital TV set-top box consists of a tuner, QAM demodulator, TS demultiplexer, MPEG-2 decoder, PAUNTSC video encoder, embedded CPU system and peripheral interfaces, CA module, and uplink data m...[Details]
With the development of science, the use of variable frequency technology is becoming more and more widespread, and it is used in both industrial equipment and household appliances. Inverter air co...[Details]
With growing environmental awareness, the continuous improvement of three-electric technology and the increasing deployment of infrastructure such as charging stations, the electrification of new e...[Details]
On August 21, according to a report by Korean media SEDaily yesterday, according to semiconductor industry sources, the HBM4 samples provided by Samsung to Nvidia last month have passed initial tes...[Details]
New version helps developers build secure and trustworthy embedded systems
Shanghai, China—August 21, 2025—
QNX, a division of BlackBerry Ltd., today announced the release of QNX...[Details]
The composition of the water heater
The water heater itself is divided into the following parts:
1. Water tank.
This is where the water heater is filled with water and where the wate...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
