UPD703216A2 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > UPD703216A2

Preview

UPD703216A2: Description32-Bit Single-Chip Microcontrollers; File Size4MB，884 Pages; ManufacturerNEC ( Renesas ); Websitehttps://www2.renesas.cn/zh-cn/

Download Datasheet View All

UPD703216A2 Overview

32-Bit Single-Chip Microcontrollers

Preview

Download Datasheet

View All

User’s Manual

V850ES/KJ1

32-Bit Single-Chip Microcontrollers

Hardware

PD703216

PD703216(A)

PD703216(A1)

PD703216(A2)

PD703216Y

PD703216Y(A)

PD703216Y(A1)

PD703216Y(A2)

PD703217

PD703217(A)

PD703217(A1)

PD703217(A2)

PD703217Y

PD703217Y(A)

PD703217Y(A1)

PD703217Y(A2)

PD70F3217

PD70F3217(A)

PD70F3217Y

PD70F3217Y(A)

PD70F3217H

PD70F3217HY

PD70F3218H

PD70F3218HY

Document No. U16889EJ1V0UD00 (1st edition)

Date Published March 2004 N CP(K)

2004

Printed in Japan

NOTES FOR CMOS DEVICES

VOLTAGE APPLICATION WAVEFORM AT INPUT PIN

Waveform distortion due to input noise or a reflected wave may cause malfunction. If the input of the

CMOS device stays in the area between V

(MAX) and V

(MIN) due to noise, etc., the device may

malfunction. Take care to prevent chattering noise from entering the device when the input level is fixed,

and also in the transition period when the input level passes through the area between V

(MAX) and

(MIN).

HANDLING OF UNUSED INPUT PINS

Unconnected CMOS device inputs can be cause of malfunction. If an input pin is unconnected, it is

possible that an internal input level may be generated due to noise, etc., causing malfunction. CMOS

devices behave differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed

high or low by using pull-up or pull-down circuitry. Each unused pin should be connected to V

or GND

via a resistor if there is a possibility that it will be an output pin. All handling related to unused pins must

be judged separately for each device and according to related specifications governing the device.

PRECAUTION AGAINST ESD

A strong electric field, when exposed to a MOS device, can cause destruction of the gate oxide and

ultimately degrade the device operation. Steps must be taken to stop generation of static electricity as

much as possible, and quickly dissipate it when it has occurred.

Environmental control must be

adequate. When it is dry, a humidifier should be used. It is recommended to avoid using insulators that

easily build up static electricity. Semiconductor devices must be stored and transported in an anti-static

container, static shielding bag or conductive material. All test and measurement tools including work

benches and floors should be grounded.

The operator should be grounded using a wrist strap.

Semiconductor devices must not be touched with bare hands. Similar precautions need to be taken for

PW boards with mounted semiconductor devices.

STATUS BEFORE INITIALIZATION

Power-on does not necessarily define the initial status of a MOS device. Immediately after the power

source is turned ON, devices with reset functions have not yet been initialized. Hence, power-on does

not guarantee output pin levels, I/O settings or contents of registers. A device is not initialized until the

reset signal is received. A reset operation must be executed immediately after power-on for devices

with reset functions.

Purchase of NEC Electronics I

C components conveys a license under the Philips I

C Patent Rights to

use these components in an I

C system, provided that the system conforms to the I

C Standard

Specification as defined by Philips.

Caution:

PD70F3217H, 70F3217HY, 70F3218H, and 70F3218HY use SuperFlash

technology

licensed from Silicon Storage Technology, Inc.

Windows and Windows NT are either registered trademarks or trademarks of Microsoft Corporation in

the United States and/or other countries.

PC/AT is a trademark of International Business Machines Corporation.

SPARCstation is a trademark of SPARC International, Inc.

Solaris and SunOS are trademarks of Sun Microsystems, Inc.

SuperFlash is a registered trademark of Silicon Storage Technology, Inc. in several countries

including the United States and Japan.

User’s Manual U16889EJ1V0UD

These commodities, technology or software, must be exported in accordance

with the export administration regulations of the exporting country.

Diversion contrary to the law of that country is prohibited.

•

The information in this document is current as of February, 2004. The information is subject to

change without notice. For actual design-in, refer to the latest publications of NEC Electronics data

sheets or data books, etc., for the most up-to-date specifications of NEC Electronics products. Not

all products and/or types are available in every country. Please check with an NEC Electronics sales

representative for availability and additional information.

•

No part of this document may be copied or reproduced in any form or by any means without the prior

written consent of NEC Electronics. NEC Electronics assumes no responsibility for any errors that may

appear in this document.

•

NEC Electronics does not assume any liability for infringement of patents, copyrights or other intellectual

property rights of third parties by or arising from the use of NEC Electronics products listed in this document

or any other liability arising from the use of such products. No license, express, implied or otherwise, is

granted under any patents, copyrights or other intellectual property rights of NEC Electronics or others.

•

Descriptions of circuits, software and other related information in this document are provided for illustrative

purposes in semiconductor product operation and application examples. The incorporation of these

circuits, software and information in the design of a customer's equipment shall be done under the full

responsibility of the customer. NEC Electronics assumes no responsibility for any losses incurred by

customers or third parties arising from the use of these circuits, software and information.

•

While NEC Electronics endeavors to enhance the quality, reliability and safety of NEC Electronics products,

customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To

minimize risks of damage to property or injury (including death) to persons arising from defects in NEC

Electronics products, customers must incorporate sufficient safety measures in their design, such as

redundancy, fire-containment and anti-failure features.

•

NEC Electronics products are classified into the following three quality grades: "Standard", "Special" and

"Specific".

The "Specific" quality grade applies only to NEC Electronics products developed based on a customer-

designated "quality assurance program" for a specific application. The recommended applications of an NEC

Electronics product depend on its quality grade, as indicated below. Customers must check the quality grade of

each NEC Electronics product before using it in a particular application.

"Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio

and visual equipment, home electronic appliances, machine tools, personal electronic equipment

and industrial robots.

"Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster

systems, anti-crime systems, safety equipment and medical equipment (not specifically designed

for life support).

"Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life

support systems and medical equipment for life support, etc.

The quality grade of NEC Electronics products is "Standard" unless otherwise expressly specified in NEC

Electronics data sheets or data books, etc. If customers wish to use NEC Electronics products in applications

not intended by NEC Electronics, they must contact an NEC Electronics sales representative in advance to

determine NEC Electronics' willingness to support a given application.

(Note)

(1) "NEC Electronics" as used in this statement means NEC Electronics Corporation and also includes its

majority-owned subsidiaries.

(2) "NEC Electronics products" means any product developed or manufactured by or for NEC Electronics

(as defined above).

M8E 02. 11-1

User’s Manual U16889EJ1V0UD

Recommended Resources

Coil short circuit tester

Simple production of negative ion generator circuit diagram

CD71061 Holiday Lights ASIC

half wave rectifier

Sensor temperature compensation principle circuit

Phase sequence detection circuit

Connection between microcontroller and gsm module: Does anyone have an example of the transceiver program for connecting wavecom and 51 microcontroller? Please let me see it and learn from it. Thank you....; maidi0018 Embedded System

A complete list of laws and regulations on professional qualifications from 2000 to 2005: A complete list of laws and regulations on professional qualifications from 2000 to 2005Source: National Labor Market November 20, 2005 10:22 Editor: Dezhou Youth Talent CenterLetter on issues concern...; fighting Analog electronics

Requesting information on RFID modulation and demodulation principles and data encryption and decryption: Dear experts, I have recently become curious about wireless security and have the following questions. I would like to ask you to answer them, haha! 1. Does the current RFID security mainly rely on me...; zhangkelei RF/Wirelessly

A good pre-game practice question: [i=s]This post was last edited by paulhyde on 2014-9-15 09:09[/i] The competition is coming soon, so I would like to share some good questions for you to practice with....; tangmb Electronics Design Contest

LED display control card common problems: [table=98%] [tr][td]What is the LED display control card? The LED display control card is the core component of the LED graphic display screen. It is responsible for receiving the screen display infor...; 方学放 LED Zone

How to know what data the RS485 differential signal (between AB) is?: [i=s] This post was last edited by yhye2world on 2017-11-12 11:15 [/i] [size=14px] Ask: [/size] [size=14px] How to know what the RS485 differential signal (between AB) is? [/size] [size=14px] Thank yo...; yhye2world Integrated technical exchanges

Shortcut: 00 01 02 03 04 05 06 07 08 09 0A 0C 0F 0J 0L 0M 0R 0S 0T 0Z 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 1H 1K 1M 1N 1P 1S 1T 1V 1X 1Z 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 2G 2K 2M 2N 2P 2Q 2R 2S 2T 2W 2Z 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 3G 3H 3J 3K 3L 3M 3N 3P 3R 3S 3T 3V 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4M 4N 4P 4S 4T 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5E 5G 5H 5K 5M 5N 5P 5S 5T 5V 60 61 62 63 64 65 66 67 68 69 6A 6C 6E 6F 6M 6N 6P 6R 6S 6T 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7M 7N 7P 7Q 7V 7W 7X 80 81 82 83 84 85 86 87 88 89 8A 8D 8E 8L 8N 8P 8S 8T 8W 8Y 8Z 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9F 9G 9H 9L 9S 9T 9W

Popular Components