ATT-551F-14-35M-02 datasheet, PDF

Datasheet> All Categories > Wireless rf/communication> Radio frequency and microwave> ATT-551F-14-35M-02

ATT-551F-14-35M-02: DescriptionFixed Attenuator, 0MHz Min, 18000MHz Max; CategoryWireless rf/communication Radio frequency and microwave; File Size195KB，3 Pages; ManufacturerVertiv

Download Datasheet Parametric View All

ATT-551F-14-35M-02 Overview

Fixed Attenuator, 0MHz Min, 18000MHz Max

ATT-551F-14-35M-02 Parametric

Parameter Name	Attribute value
Maker	Vertiv
Reach Compliance Code	unknown
Other features	3.5 MM-F, I/P POWER-MAX(PEAK)=200W
Nominal attenuation	14 dB
structure	COAXIAL
Maximum input power (CW)	33.01 dBm
Maximum operating frequency	18000 MHz
Minimum operating frequency
Maximum operating temperature	125 °C
Minimum operating temperature	-65 °C
RF/Microwave Device Types	FIXED ATTENUATOR
Maximum voltage standing wave ratio	1.07

Preview

Download Datasheet

View All

Attenuators

DC - 4.0 GHz

Male/Female

ATT-0278-XX-SMA-02

SMA Ultraminiature Type

Model Numbers

Male/Male

ATT-278M-XX-SMA-02

278 Series

Female/Female

ATT-278F-XX-SMA-02

XX = Attenuation Value: Select 01-30dB in 1dB increments

(.5 dB increments available)

DC - 2.0 GHz

Male/Female

ATT-0279-XX-SMA-02

279 Series

Female/Female

ATT-279F-XX-SMA-02

Model Numbers

Male/Male

ATT-279M-XX-SMA-02

XX = Attenuation Value: Select 01-30dB in 1dB increments

(.5 dB increments available)

DC - 26.5 GHz 3.5mm High Performance

Extended Frequency Performance

0 - 20 dB Attenuation Values

3.5 mm Precision Connectors (mates with SMA)

Small Size - Light Weight

Any Male/Female Connector Configuration

Rugged Stainless Steel Construction

Midwest Microwave's 3.5 mm subminiature series of precision fixed coaxial attenuators provide extended frequency

operation of up to 26.5 GHz when mated with connector interfaces of the same family. These temperature stable, ruggedly

built, precision attenuators allow high performance in a very small light weight package size. Attenuation values up through

20 dB in 1 dB increments are available with any combination of female or male 3.5mm connectors.

SPECIFICATIONS - HIGH PERFORMANCE

VSWR:

1.07 + 0.015 f (GHz)

Frequency:

DC - 18.0, DC - 26.5 GHz

Power:

2 Watts Average @ +25

derated linearly to .5 watts @ +125

Attenuation Accuracy:

1-6 dB + 0.5 dB

Peak Power:

200 Watts

7-20 dB + 0.7 dB

Operating Temp Range:

- 65 to + 125C

Finish:

Passivated Stainless Steel

DC - 26.5 GHz

Male/Female

ATT-0550-XX-35M-02

550 Series

Female/Female

ATT-550F-XX-35M-02

Model Numbers

Male/Male

ATT-550M-XX-35M-02

Note: dimensions shown above are for the Male/Female

version. The length for the Female/Female version is

1.33 and for the Male/Male version is 1.39.

1.36

26.5 GHz Extended Frequency Performance

XX = Attenuation Value: Select 01-20dB in 1dB increments

(.5 dB increments available)

Note: For DC - 18.0 GHz Model, subsitute "551" for "550" in Model No.

Recommended Resources

Cascade MMIC amplifier circuit diagram

Temporary power lines

TTL and CMOS interface circuit a

SFG-15N1A force sensitive sensor classic circuit

Little Swan CXW-230-99B single-wheel range hood circuit diagram

820e computer motherboard circuit diagram_28

Looking for hardware personnel who can develop USB drivers and simple hardware: Everyone, I am working on a project and need your participation if you have experience: (1) USB driver development. (2) Ordinary telephone hardware. (3) Location: Shanghai. Experience is required. Sal...; nmylx Embedded System

The SD card was reset successfully, but the initialization failed to receive 00. I hope the moderator can help.: The approximate code is as follows, using the Znfat code. The reset is successful, but the initialization is not. Please help and take a look. #include "STC12C5A32S2.H" #define DELAY_TIME 10 #define T...; _ForNow_ Embedded System

Why do we need to clear to zero first and then assign the value bit by bit? Are there any loopholes in direct assignment?: Why do we first set the TMR0ON bit of T0CON to 0, and then set TMR0ON to 1 at the end? Will there be any loopholes if we directly set T0CON = 0b10001000?...; houtianze1023 Microchip MCU

I would like to ask a question about 430AD collection~~~: For example, I want to see how many data are sampled in ADC12MEM0 after the program is executed for 5 seconds (that is, how many points are sampled by AD in 5 seconds). How can I use IAR to see it? ? ...; Ben讨厌苦咖啡 Microcontroller MCU

What is the NOR flash boot method?: What is the NOR flash boot mode? How does the system select the NOR flash boot mode? I am using the ADS development environment....; ling.wo Embedded System

KiCad 9-minute quick tutorial: I saved a KiCad tutorial. Seeing that many netizens want to learn KiCad, I uploaded it to the University Hall. Let's learn together~ How many netizens want to learn and use KiCad, please raise your ha...; ohahaha PCB Design

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components