Z: Tape and reel packing (Picked from the 8/9/10/12-pin side)
Note: In case of 5 V transistor drive circuit, it is recommended to use 4.5 V type relay.
L: 1 coil latching
L2: 2 coil latching
ds_61022_en_txd: 280114D
1
TX-D
TYPES
1. Standard (B.B.M.) type
1) Standard PC board terminal
Contact
arrangement
Nominal coil
voltage
1.5V DC
3V DC
4.5V DC
2 Form C
5V DC
6V DC
9V DC
12V DC
24V DC
Single side stable
Part No.
TXD2-1.5V
TXD2-3V
TXD2-4.5V
TXD2-5V
TXD2-6V
TXD2-9V
TXD2-12V
TXD2-24V
1 coil latching
Part No.
TXD2-L-1.5V
TXD2-L-3V
TXD2-L-4.5V
TXD2-L-5V
TXD2-L-6V
TXD2-L-9V
TXD2-L-12V
TXD2-L-24V
Standard packing: Tube: 40 pcs.; Case: 1,000 pcs.
Note: Please add “-1” to the end of the part number for AgPd contacts (low level load).
2) Surface-mount terminal
(1) Tube packing
Contact
arrangement
Nominal coil
voltage
1.5V DC
3V DC
4.5V DC
2 Form C
5V DC
6V DC
9V DC
12V DC
24V DC
Single side stable
Part No.
TXD2S-1.5V
TXD2S-3V
TXD2S-4.5V
TXD2S-5V
TXD2S-6V
TXD2S-9V
TXD2S-12V
TXD2S-24V
1 coil latching
Part No.
TXD2S-L-1.5V
TXD2S-L-3V
TXD2S-L-4.5V
TXD2S-L-5V
TXD2S-L-6V
TXD2S-L-9V
TXD2S-L-12V
TXD2S-L-24V
:
For each surface-mount terminal identification, input the following letter. SA type: A, SS type: S
Standard packing: Tube: 40 pcs.; Case: 1,000 pcs.
Note: Please add “-1” to the end of the part number for AgPd contacts (low level load).
(2) Tape and reel packing
Contact
arrangement
Nominal coil
voltage
1.5V DC
3V DC
4.5V DC
2 Form C
5V DC
6V DC
9V DC
12V DC
24V DC
Single side stable
Part No.
TXD2S-1.5V-Z
TXD2S-3V-Z
TXD2S-4.5V-Z
TXD2S-5V-Z
TXD2S-6V-Z
TXD2S-9V-Z
TXD2S-12V-Z
TXD2S-24V-Z
1 coil latching
Part No.
TXD2S-L-1.5V-Z
TXD2S-L-3V-Z
TXD2S-L-4.5V-Z
TXD2S-L-5V-Z
TXD2S-L-6V-Z
TXD2S-L-9V-Z
TXD2S-L-12V-Z
TXD2S-L-24V-Z
:
For each surface-mount terminal identification, input the following letter. SA type: A, SS type: S
Standard packing: Tape and reel: 500 pcs.; Case: 1,000 pcs.
Notes: 1. Tape and reel packing symbol “-Z” is not marked on the relay. “X” type tape and reel packing (picked from 1/3/4/5-pin side) is also available.
2. Please add “-1” to the part number for AgPd contacts (low level load). (Ex. TXD2SA-1.5V-1-Z)
2
ds_61022_en_txd: 280114D
TX-D
2. M.B.B type
1) Standard PC board terminal
Contact arrangement
Nominal coil voltage
1.5V DC
3V DC
4.5V DC
2 Form C
5V DC
6V DC
9V DC
12V DC
24V DC
Standard packing: Tube: 40 pcs.; Case: 1,000 pcs.
Single side stable
Part No.
TXD2-2M-1.5V
TXD2-2M-3V
TXD2-2M-4.5V
TXD2-2M-5V
TXD2-2M-6V
TXD2-2M-9V
TXD2-2M-12V
TXD2-2M-24V
2) Surface-mount terminal
(1) Tube packing
Contact arrangement
Nominal coil voltage
1.5V DC
3V DC
4.5V DC
2 Form C
5V DC
6V DC
9V DC
12V DC
24V DC
:
For each surface-mount terminal identification, input the following letter. SA type: A, SS type: S
Standard packing: Tube: 40 pcs.; Case: 1,000 pcs.
Single side stable
Part No.
TXD2S-2M-1.5V
TXD2S-2M-3V
TXD2S-2M-4.5V
TXD2S-2M-5V
TXD2S-2M-6V
TXD2S-2M-9V
TXD2S-2M-12V
TXD2S-2M-24V
(2) Tape and reel packing
Contact arrangement
Nominal coil voltage
1.5V DC
3V DC
4.5V DC
2 Form C
5V DC
6V DC
9V DC
12V DC
24V DC
Single side stable
Part No.
TXD2S-2M-1.5V-Z
TXD2S-2M-3V-Z
TXD2S-2M-4.5V-Z
TXD2S-2M-5V-Z
TXD2S-2M-6V-Z
TXD2S-2M-9V-Z
TXD2S-2M-12V-Z
TXD2S-2M-24V-Z
:
For each surface-mount terminal identification, input the following letter. SA type: A, SS type: S
Standard packing: Tape and reel: 500 pcs.; Case: 1,000 pcs.
Notes: 1. Types designed to withstand strong vibration caused, for example, by the use of terminal cutters, can also be ordered.
However, please contact us if you need parts for use in low level load. (Ex. TXD2SA-2M-1.5V-1-Z)
2. Tape and reel packing symbol “-Z” is not marked on the relay. “X” type tape and reel packing (picked from 1/3/4/5-pin side) is also available.
(By resistive method, nominal coil voltage applied to the coil;
contact carrying current: 2A [1A: M.B.B.].)
Max. 4 ms [Max. 4 ms] (Nominal coil voltage applied to the coil, excluding contact bounce time.)
Max. 4 ms [Max. 4 ms] (Nominal coil voltage applied to the coil, excluding contact bounce time.)
(without diode)
Min. 750 m/s
2
(Half-wave pulse of sine wave: 6 ms;
detection time: 10s.)
Min. 500 m/s
2
(Half-wave pulse of sine wave: 11 ms;
detection time: 10s.)
250mW (1.5 to 12 V DC), 270mW (24 V DC)
—
500 Vrms for 1min. (Detection current: 10mA)
3,000 Vrms for 1min. (Detection current: 10mA)
—
1 A 30 V DC (resistive load)
30 W (DC) (resistive load)
110 V DC
1A
Min. 1,000M (at 500V DC) Measurement at same location as “Initial breakdown voltage” section.
1,000 Vrms for 1min. (Detection current: 10mA)
Temperature rise (at 20C
68F)
Operate time [Set time] (at 20C
68F)
Release time [Reset time] (at 20C
68F)
Functional
Destructive
Vibration
resistance
Mechanical
Expected life
Electrical
Conditions for operation, transport and
storage
*2
Max. operating speed (at rated load)
Unit weight
*1
*2
Functional
Destructive
Mechanical
characteristics
Shock
resistance
Min. 1,000 m/s
2
{100G} (Half-wave pulse of sine wave: 6 ms.)
10 to 55 Hz at double amplitude of 3.3 mm (Detection time: 10s.)
10 to 55 Hz at double amplitude of 5 mm
Min. 10 (at 180 cpm)
8
Min. 10
7
(at 180 cpm)
Min. 10
5
(1 A 30 V DC resistive) (at 20 cpm)
Min. 10
5
(2 A 30 V DC resistive),
Min. 510
5
(1 A 30 V DC resistive) (at 20 cpm)
Conditions
Ambient temperature: –40C to +85C
–40F to +185F;
Humidity: 5 to 85% R.H. (Not freezing and condensing at low temperature)
20 cpm
Approx. 2 g
.071 oz
This value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the actual
load. (AgPd contact type is available for low level load switching.)
The upper operation ambient temperature limit is the maximum temperature that can satisfy the coil temperature rise value. Refer to “6. Usage, Storage and Transport
Conditions“ in
AMBIENT ENVIRONMENT section in Relay Technical Information.
2440 board, generally the display is normal after power on, but occasionally after power on, the display will shift upward or downward by about 20-50 lines. Our products have to go through high temper...
I am a novice and have not been in contact with VxWorks for a long time. I have no problem compiling in the Tornado development environment. But when I download it to DSP, it reports an error saying t...
I want to design a high-resolution A/D converter and use ad650 to make a voltage-frequency conversion circuit. However, the output waveform is particularly unstable due to welding or some other reason...
I just installed this version of the software, but I don't know if it has been improved. However, new routines have been added to dk-tm4c123g. I originally installed version 1.0 [[i] This post was las...
samba/lib/codepages/unicode_map.ISO8859-1 does not exist. added interface ip=192.168.1.2 bcast=192.168.1.255 nmask=255.255.255.0 session request to 192.168.1.188 failed (Called name not present) sessi...
Introduction
Power subsystems are becoming more and more integrated into the overall system. Power systems have moved from being separate "essential dangerous devices" to being monitorable...[Details]
1. Principle of displacement angle sensor
The angle sensor is used to detect angles. It has a hole in its body that fits the LEGO axle. When connected to the RCX, the angle sensor counts once ...[Details]
We know that microcontroller development tools generally include real-time online emulators and programmers. Among them, online emulators are very good tools, but they are also more expensive...[Details]
1. Disadvantages of choosing too high a voltage level
Choosing too high a voltage level will result in too high an investment and a long payback period. As the voltage level increases, the...[Details]
In today's body control module (BCM) designs, savvy engineers are moving away from electromechanical relays whenever possible. Their next step is to eliminate fuses. But is eliminating fuses a nece...[Details]
Corelink Semiconductor has launched the CL1100-based 5-7W E27 LED lighting driver system solution DB2. This driver module meets the requirements of small size (L×W×H=5.1cm×2.1cm×1.8cm), low standby...[Details]
Liquid crystal display (LCD) panels have a wide range of applications, from small portable electronic devices to large fixed devices, including digital cameras, laptops, personal data assistants, d...[Details]
Traditional
virtual instruments
consist of a data acquisition
board
based on PCI bus and
corresponding software. However, with
the rapid development of
computer
network techno...[Details]
When the so-called "copycat phones" that flood the domestic mobile phone market move towards large screens, stereo amplifiers, touch controls, and even GPS navigation and mobile TV, the homogeneity...[Details]
1 Development of LED Film and Television Lighting
1.1 The significance of developing film and television lighting
Lighting power consumption accounts for a large proportion of the total p...[Details]
1 Load Regulation
Changes in power supply load will cause changes in power supply output. When the load increases, the output decreases, and vice versa, when the load decreases, the output inc...[Details]
Mobile phones, MP3s, tablet computers, laptops, digital cameras, handheld game consoles, navigation devices, etc., all these mobile devices are powered by mobile batteries, and the battery life is ...[Details]
The automotive power electronics market has grown rapidly as comfort and active safety features become more common. As traditional mechanical functions shift to electronic applications, the demand ...[Details]
1 Introduction
Power supply ripple will interfere with the normal operation of electronic equipment, causing malfunctions such as computer crashes, data processing errors and control system fa...[Details]
1 Introduction
Fieldbus is a serial, digital, multi-point communication data bus between field equipment/instruments installed in the production process area and automatic control devices/syst...[Details]
ARM Technology
京公网安备 11010802033920号
EEWORLD
