and CE2# allows 8-bit hosts to access all data on DQ0 - DQ7.
OUTPUT ENABLE:
Active low signal gating read data from the memory card.
WRITE ENABLE:
Active low signal gating write data to the memory card.
READY/BUSY OUTPUT:
Indicates status of internally timed erase or program algorithms. A high output indicates that
the card is ready to accept accesses. A low output indicates that one or more devices in the memory card are busy with
internally timed erase or write activities.
CARD DETECT 1 and 2:
Provide card insertion detection. These signals are connected to ground internally on the
memory card. The host socket interface circuitry shall supply 10K-ohm or larger pull-up resistors on these signal pins.
WRITE PROTECT:
Write protect reflects the status of the Write Protect switch on the memory card. WP set to high =
write protected, providing internal hardware write lockout to the Flash array.If card does not include optional write protect
switch, this signal will be pulled low internally indicating write protect = “off”.
PROGRAM/ERASE POWER SUPPLY:
Not connected for 5V only card.
CARD POWER SUPPLY:
5.0V for all internal circuitry.
GROUND:
for all internal circuitry.
INPUT
INPUT
OUTPUT
OUTPUT
OUTPUT
ATTRIBUTE MEMORY SELECT:
provides access to Flash memory card registers and Card Information Structure in the
Attribute Memory Plane.
RESET:
Active high signal for placing card in Power-on default state. Reset can be used as a Power-Down signal for the
memory array.
WAIT:
This signal is pulled high internally for compatibility. No wait states are generated.
BATTERY VOLTAGE DETECT:
These signals are pulled high to maintain SRAM card compatibility.
VOLTAGE SENSE:
Notifies the host socket of the card’s V
CC
requirements. VS1 and VS2 are open to indicate a 5V
card has been inserted.
4
White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com
CD1#, CD2#
WP
OUTPUT
OUTPUT
V
PP
1, V
PP
2
V
CC
GND
REG#
RST
WAIT
BVD1, BVD2
VS1, VS2
N.C.
White Electronic Designs Corp. reserves the right to change products or specifications without notice.
March, 2003
Rev. 6
White Electronic Designs
Operating Temperature TA (ambient)
Commercial
Industrial
Storage Temperature
Commercial
Industrial
Voltage on any pin relative to V
SS
V
CC
supply Voltage relative to V
SS
** Advanced information
PCMCIA Flash Memory Card
FLD Series
Absolute Maximum Ratings
(2)
0°C to +60 °C
-40°C to +85 °C **
-30°C to +80 °C
-40°C to +85 °C **
-0.5V to V
CC
+0.5V (1)
-0.5V to +7.0V
Notes:
(1)
During transitions, inputs may undershoot to -2.0V or overshoot to V
CC
+2.0V for periods less than 20ns.
(2)
Stress greater than those listed under “Absolute Maximum ratings” may cause permanent damage to the device. This is a stress rating only
and functional operation at these or any other conditions greater than those indicated in the operational sections of this specification is not
implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
DC Characteristics
(1)
Sym
I
CCR
I
CCW
I
CCE
I
CCS
Parameter
V
CC
Read Current
V
CC
Program Current
V
CC
Erase Current
V
CC
Standby Current
Density
(Mbytes)
All
All
All
2MB
(4MB)
Notes
Typ
(4)
Max
75
150
150
Units
mA
mA
mA
µA
Test Conditions
V
CC
= 5V +/- 10%
tcycle = 150ns
2,3
80
230
V
CC
= 5V +/- 10%
Control Signals = V
IL
or V
OH
Reset = V
SS
Test Conditions: V
CC
= 5V ± 10%, V
I
= V
IL
or V
IH
Notes:
1.
All currents are RMS values unless otherwise specified. I
CCR
, I
CCW
and I
CCE
are based on Word wide operations.
2.
Control Signals: CE
1#
, CE
2#
, OE#, WE#, REG#.
3.
I
CCD
and I
CCS
are specified for lowest density card for each component type (2MB for 8Mb components and 4MB for 16Mb components) This represents a single pair of devices.
For higher densities multiply the number of device pairs by the specified current in the table. For example a 40MB card will use 10 device pairs of 16Mb components. The
maximum I
CCD
will be 10 x 40µA = 400µA. The maximum I
CCS
will be 10 x 230µA = 2.3mA.
4. Typical: V
CC
= 5V, T = +25°C.
Symbol Parameter
I
LI
Input Leakage Current
I
LO
V
IL
V
IH
V
OL
V
OH
V
LKO
Output Leakage Current
Input Low Voltage
Input High Voltage
Output Low Voltage
Output High Voltage
V
CC
Erase/ProgramLock Voltage
Notes
1
1
1
1
1
1
1
Min
Max
±20
±20
Units
µA
µA
V
V
V
V
V
Test Conditions
V
CC
= 5V +/- 10%
V
IN
=V
CC
or V
SS
V
CC
= 5V +/- 10%
V
OUT
=V
CC
or V
SS
0
2
3.98
3.2
0.8
0.26
4.2
I
OL
= 4mA
I
OH
= -4mA
Notes:
1. Values are the same for byte and word wide modes for all card densities.
2. Exceptions: Leakage currents on CE
1#
, CE
2#
, OE#, REG# and WE# will be < 500 µA when V
IN
= GND due to internal pull-up resistors. Leakage currents on RST will be <150µA
when V
IN
=V
CC
due to internal pull-down resistor.
White Electronic Designs Corp. reserves the right to change products or specifications without notice.
March, 2003
Rev. 6
5
White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com
[backcolor=white][size=3][color=#000000]In the case of mixed programming of C/C++ and assembly language, we usually choose C/C++ to implement most of the expected functions. Assembly is used to implem...
I was interested in electronics before, but I could never find a direction to study. I always felt like I was stuck in the same place and my studies were not very effective. Now I finally have some di...
Can I only use evc++ to develop upper-level applications on a wince5.0 board? The application development environment for wince6.0 is vs2005, does that mean I can use C# to develop? I want to use C# t...
I have installed vs2005, activesync, Windows Mobile 5.0 Pocket PC SDK and Windows Mobile 5.0 Emulator Images for Pocket PC. How can I download the MFC program from the PC to the Windows Mobile emulato...
Vertical cavity surface emitting lasers (VCSELs) are gradually replacing traditional edge emitting lasers, especially in low bandwidth and short-distance communication systems where cost factors ar...[Details]
Investment in
the
medical device
industry has been on the rise in recent years. In the past two years, venture capital for medical devices has almost doubled, reaching $4 billion in 2007. Fr...[Details]
Motors are important products that convert electrical energy into mechanical energy to achieve automation, and they are widely used in industrial control, medical electronics, white a...[Details]
Recently, news came from the certification department that the photovoltaic grid-connected inverter of Samil New Energy Co., Ltd. (hereinafter referred to as "Samil New Energy") has once again obta...[Details]
The rectified DC voltage is then converted back to AC using power electronics such as insulated gate bipolar transistors.
The output voltage is switched on and off at a high frequency, control...[Details]
0 Introduction
With the rapid development of modern power electronics technology, various power electronic devices have been widely used in various fields such as power systems, industry, an...[Details]
The biggest advantage of Profibus is that it is guaranteed by the stable international standard EN50170 and has been proven to be universal in practical applications. It has been widely used in man...[Details]
The programmable controller directly controls the stepper motor, which can significantly reduce the cost of the control system of the modular machine tool automatic production line. The article int...[Details]
0 Introduction
Pneumatic
artificial muscle,
also known as pneumatic muscle actuator (PMA), began to be studied in the 1950s. In recent years, it has been widely studied and applied ...[Details]
Globally, the market for airbags and other restraint systems consists of different geographical regions, each with its own characteristics and needs. North America first introduced airbags in mass-...[Details]
Various electronic and electromagnetic interference inside and outside the car often puts automotive electronic equipment in dangerous working conditions, degrading the performance of electronic eq...[Details]
AUTOSAR is a hierarchical architecture for automotive electronic embedded software jointly launched by global automotive OEMs and suppliers. The hierarchical architecture consists of a microcontrol...[Details]
1. Low temperature storage
Lithium-ion power batteries need to be fully charged before storage. They can be stored at 20°C for more than half a year, which shows that lithium-ion power batteri...[Details]
Li/SOCl2 batteries (lithium sub-cells) have the advantages of high operating voltage, stable discharge voltage, wide operating temperature range and long storage life, and have been widely used in ...[Details]
With the development of power electronics technology and high-performance permanent magnet materials, the application of brushless DC motors has achieved rapid development in the fields of aerospace, ...[Details]
DSP and ARM Processors
京公网安备 11010802033920号
EEWORLD
