Pl tronics, Inc.
.
19013 36th Ave. W, Suite H Lynnwood, WA 98036 USA
Manufacturer of High Quality Frequency Control Products
Differential PECL Series
Differential PECL Output, Some with Enable/ Disable Function
Available in 9 Different Package/Configurations, See Next Pages
Standard Specifications
Overall Frequency Stability
Operating Temperature Range
Storage Temperature Range
Supply Voltage (Vcc)
Supply Current (Icc)
Output High Level
± 50 PPM, ± 25 PPM, ± 20 PPM over Operating Temperature Range
0 to +80°C is standard, but can be extended to - 40 to +85°C
- 55 to +125°C
3.3 volts ± 5% standard, but 5.0 volts or 2.5 volts also available. See Test Cirucit 5.
< 250 MHz = 90 mA maximum, 250 MHz and above = 100 mA maximum
2.275 V minimum referenced to Ground, Vcc = 3.300V,
0.975 V minimum referenced to termination voltage,
- 1.025 V minimum referenced to Vcc
1.680 V maximum referenced to Ground, Vcc = 3.300V,
0.380 V maximum referenced to termination voltage,
- 1.620 V maximum referenced to Vcc
45/55% referenced to 50% of amplitude
1.0 nS maximum when Vth is 10% and 90% of waveform
1 pS RMS maximum measured
from 12 kHz to 20 MHz from Fnominal
50 kohm minimum to Vcc
0.3 Vcc maximum referenced to Ground
0.7 Vcc minumum referenced to Ground
Output Low Level
Output Symmetry
Output Rise & Fall (Tr & Tf)
Jitter
E/D Internal Pullup
V disable
V enable
PE7745D only Output Enable / Disable
High Level Input Current
-20 uA maximum at Enable / Disable Pin = 0.7 Vcc
Low Level Input Current
-200 uA maximum at Enable / Disable Pin = 0 V
Output Enable Time
200 nS maximum at output enable or 1 mS maximum at output enabled and stable
Output Disable Time
200 nS maximum at output disable
Vcc Supply Current disabled < 1 mA. Both outputs are high impedance when disabled.
All other models Output Enable/Disable (E/D)
Output Enable Time
100 nS maximum
Output Disable Time
100 nS maximum
When Disabled
Q Output = Logic Low, QN Output = Logic High. Both Outputs are active
Note 1:
PECL and ECL are identical circuits.
ECL has the most positive pin as ground and is ideally terminated by 50 ohms to - 2.00 V
PECL has the most negative pin as ground and is ideally terminated by 50 ohms to the most (positive voltage less 2.00 V)
Mechanical: See Next Pages
D Package
J Package Replacement
B Package
M Package
Mar 2004
Pl tronics, Inc.
(425) 776 -1880, Fax: (425) 776-2760, ple-sales@pletronics.com, www.pletronics.com
1
PECL, LVDS, OCXO
Page 1 - 7
19013 36th Ave. W, Suite H Lynnwood, WA 98036 USA
Manufacturer of High Quality Frequency Control Products
B Package PECL Series
PE1145T, PE1145B, PE3345B, PE3745B
Differential PECL Output with Enable/ Disable Function, 5.0 Vcc or 3.3 Vcc
6 Pad 14x10x3mm Leadless Surface Mount Clock Oscillator
Part Numbering Guide
Portions of the part number that appear after the frequency may not be marked on part (C of C provided)
PE11 45 B V - 70.0M - XXX
(Internal Code or blank)
1.50 MHz
–
650.00 MHz
Model Series
> 120.0 MHz to 650 MHz (5.0 Vcc)
> 180.0 MHz to 650 MHz (3.3 Vcc)
PE1145T = E/D on pin2
Packaging
Tube or
24mm tape,
16mm pitch
Frequency in MHz
Special Specifications (choose all that apply)
E: Extended Operating Temperature Range (- 40 to +85
°
C)
F: 47.5 /52.5% Symmetry at 50% of Vcc
V: Supply Voltage of 3.3 volts
±
10%
Y: Supply Voltage of 5.0 volts
±
10%
Frequency Stability
45 = ± 50 PPM
44 = ± 25 PPM
20 = ± 20 PPM
1.5 MHz to 120 MHz (5.0 Vcc)
1.5 MHz to 180 MHz (3.3 Vcc)
PE1145B = E/D on pin2, QN on pin 1
PE3345B = E/D on pin 2, QN on pin 5
PE3745B = E/D on pin 1, QN on pin 5
Consult factory for available frequencies and specs. Not all options available for all frequencies. A special part number may be assigned.
Frequency Stability is inclusive of frequency shifts due to calibration, temperature, supply voltage, shock, vibration and load
Mechanical: inches (mm)
not to scale
Solder Pads
0.200 (5.08)
Due to part size and factory abilities, part marking may vary from lot to lot and may contain our part number or an internal code.
0.400 (10.16) MAX
4
5
6
3
2
1
1
2
3
0.560 (14.23) MAX
0.125 (3.17)
MAX
0.200 (5.08)
0.055 0 .145
(1.4)
(3.68)
PE1145T
PIN
1
2
3
4
5
6
SIGNAL
N.C.
E/D
GND
Q OUT
QN OUT
Vcc
PE1145B
PIN
1
2
3
4
5
6
SIGNAL
QN OUT
E/D
GND
Q OUT
N.C.
Vcc
PE3345B
PIN
1
2
3
4
5
6
SIGNAL
N.C.
E/D
GND
Q OUT
QN OUT
Vcc
PE3745B
PIN
1
2
3
4
5
6
SIGNAL
E/D
N.C.
GND
Q OUT
QN OUT
Vcc
See page 6 for Layout Guidelines
> 180.0 MHz to 650.0 MHz (3.3 Vcc)
> 120.0 MHz to 650.0 MHz (5.0 Vcc)
Jun 2004
1.5 MHz to 180.0 MHz (3.3 Vcc)
1.5 MHz to 120.0 MHz (5.0 Vcc)
2A
Pl tronics, Inc.
(425) 776 -1880, Fax: (425) 776-2760, ple-sales@pletronics.com, www.pletronics.com
0.118 0.228 (5.8)
(3.0)
6
5
4
PECL, LVDS, OCXO
Page 1 - 7
Pl tronics, Inc.
.
Pl tronics, Inc.
.
19013 36th Ave. W, Suite H Lynnwood, WA 98036 USA
Manufacturer of High Quality Frequency Control Products
PECL and LVDS Layout Guidelines
SUGGESTED PCB LAYOUTS
Solder Pad Layout which
accommodates all PECL surface mount
devices
0.200 (5.08)
0 .185
(4.7)
0 .087
(2.2)
'B Pkg'
5 x7
TOP SIDE
BYPASS
BOTTOM
SIDE
BYPASS
0.055 0.100
(1.4) (2.54)
The output line should be designed with proper characteristic
impedance. Pletronics recommends laying out for the larger
'B package' with pads long enough to accept the smaller
5 x 7mm device. This permits the best option for alternate
sources of device. Pletronics also recommends connecting
Pin 1 and Pin 2 together on the models with
Q & QN OUT on pins 4 & 5. This allows
having E/D on either pin 1 or pin 2.
MULTI
LAYER
BYPASS
For Optimum Jitter Performance, Pletronics recommends:
A ground plane under the device with any other signals below the ground plane
Minimize other RF signals near device
No large transient signals (both current and voltage) should be routed under the device
Do not layout near a large magnetic field such as a high frequency switching power supply
Do not place near piezoelectric buzzers or mechancial fans
Reflow Cycle for lead free processing
250
Temperature
°
C
200
150
100
215°C
±
10°C
50 Seconds
175°C
±
10°C
120 to 160 Seconds
260°C max
10 Seconds max
T Rise= 4 Degree/second max
Mar 2004
Pl tronics, Inc.
(425) 776 -1880, Fax: (425) 776-2760, ple-sales@pletronics.com, www.pletronics.com
6
PECL, LVDS, OCXO
Page 1 - 7
Pl tronics, Inc.
.
19013 36th Ave. W, Suite H Lynnwood, WA 98036 USA
Manufacturer of High Quality Frequency Control Products
PECL and LVDS Layout Guidelines Continued
PECL Terminations:
Suggested Terminations for 50 ohm impedance matched termination
Vcc
Vcc
R1
Vcc
Out
Oscillator
GND
Vcc
Out
Oscillator
GND
Thevenin Equivalent Termination
Vcc
5.0 V
3.3 V
2.5 V
R1
82 ohm
130 ohm
249 ohm
R2
130 ohm
82 ohm
61.9 ohm
50 ohm
Vcc - 2.00 V
R2
Simple termination for NON impedance matched termination
Vcc
Vcc
Out
Oscillator
GND
R load
Vcc
5.0 V
3.3 V
2.5 V
R load
274 ohm
147 ohm
86.6 ohm
LVDS Terminations:
Vcc
Vcc
Q Out
Oscillator
GND QN Out
100 ohm
Design PCB traces for 50 ohm characteristic impedance
Mixed System Power Supply:
PECL
ECL
LVDS
To use multiple supply voltages requires level translation. Direct circuit connection is not valid.
Mixed supply voltages are allowed. No translation is necessary. (ECL is returned to the most positive
supply and this is common to all circuits)
Mixed supply voltages are allowed. LVDS signal levels are power supply independent.
3.3 V LVDS oscillators properly interface 2.5 V Logic Arrays for example.
Mar 2004
6A
Pl tronics, Inc.
(425) 776 -1880, Fax: (425) 776-2760, ple-sales@pletronics.com, www.pletronics.com
京公网安备 11010802033920号
EEWORLD
