Vectron’s VCC6 Crystal Oscillator is a quartz stabilized, differential output oscillator, operating off either a 2.5 or 3.3 volt supply,
hermetically sealed 5x7 ceramic package.
Features
•
•
•
•
•
•
•
Ultra Low Jitter Performance, Fundamental or 3rd OT Crystal Design
Output Frequencies to 275.000MHz
0.3 ps typical RMS jitter, 12k-20MHz
Differential Output
Enable/Disable
-10/70°C, -40/85°C or -55/125°C Operation
Hermetically Sealed 5x7 Ceramic Package
•
•
•
•
•
•
•
•
•
•
Applications
Ethernet, GbE, Synchronous Ethernet
Fiber Channel
Enterprise Servers
Telecom
Clock source for A/D’s, D/A’s
Driving FPGA’s
Test and Measurement
PON
Medical
COTS
• Product is compliant to RoHS directive
and fully compatible with lead free assembly
Block Diagram
Complementary
Output
Output
V
DD
Crystal
Oscillator
E/D or NC
E/D or NC
Gnd
Page1
Performance Specifications
Table 1. Electrical Performance, LVPECL Option
Parameter
Voltage
1
Current (No Load)
Nominal Frequency
2
Stability
2,3
(Ordering Option)
Outputs
Output Logic Levels
4
, -10/70°C
Output Logic High
Output Logic Low
Output Logic Levels
4
, -40/85°C
Output Logic High
Output Logic Low
Output Rise and Fall Time
4
Load
Duty Cycle
5
Jitter (12 kHz - 20 MHz BW)155.52MHz
6
Period Jitter
7
RMS
P/P
Random Jitter
Deterministic Jitter
Output Enabled
8
Output Disabled
Disable Time
Enable/Disable Leakage Current
Enable Pull-Up Resistor
Output Enabled
Output Disabled
Start-Up Time
Operating Temp. (Ordering Option)
t
SU
T
OP
-10/70, -40/85 or -55/125
33
1
10
фJ
фJ
2.3
20
2.4
0
Enable/Disable
V
IH
V
IL
t
D
0.7*V
DD
0.3*V
DD
200
±200
V
V
ns
uA
KOhm
MOhm
ms
°C
ps
ps
ps
ps
45
V
OH
V
OL
V
OH
V
OL
t
R
/t
F
50 ohms into V
DD
-1.3V
50
0.3
55
0.7
%
ps
V
DD
-1.025
V
DD
-1.810
V
DD
-1.085
V
DD
-1.830
V
DD
-0.880
V
DD
-1.620
V
DD
-0.880
V
DD
-1.555
600
V
V
V
V
ps
Symbol
V
DD
I
DD
Min
Supply
3.135
2.375
Frequency
Typical
3.3
2.5
50
Maximum
3.465
2.625
98
275.000
Units
V
V
mA
MHz
ppm
f
N
25
±20, ±25, ±50, ±100
1. The VCC6 power supply pin should be filtered, eg, a 0.1 and 0.01uf capacitor.
2. See Standard Frequencies and Ordering Information for more information.
3. Includes calibration tolerance, operating temperature, supply voltage variations, aging and IR reflow.
4. Figure 1 defines the test circuit and Figure 2 defines these parameters.
5. Duty Cycle is defined as the On/Time Period.
6. Measured using an Agilent E5052, 155.520MHz. Please see “Typical Phase Noise and Jitter Report for the VCC6 series”.
7. Measured using a Wavecrest SIA3300C, 90K samples.
8. Outputs will be Enabled if Enable/Disable is left open.
V
DD
-1.3V
t
R
V
OH
50%
t
F
1
NC
2
NC
3
6
5
4
50
50
V
OL
On Time
-1.3V
Period
Figure 1.
Page2
Figure 2.
Performance Specifications
Table 2. Electrical Performance, LVDS Option
Parameter
Voltage
1
Current (No Load)
Nominal Frequency
2
Stability
2,3,
(Ordering Option)
Outputs
Output Logic Levels
4
Output Logic High
Output Logic Low
Differential Output Amplitude
Differential Output Error
Offset Voltage
Offset Voltage Error
Output Leakage Current
Output Rise and Fall Time
4
Load
Duty Cycle
5
Jitter (12 kHz - 20 MHz BW)155.52MHz
6
Period Jitter
7
RMS
P/P
Random Jitter
Deterministic Jitter
Output Enabled
8
Output Disabled
Disable Time
Enable/Disable Leakage Current
Enable Pull-Up Resistor
Output Enabled
Output Disabled
Start-Up Time
Operating Temp. (Ordering Option)
t
SU
T
OP
-10/70, -40/85 or -55/125
33
1
10
фJ
фJ
2.5
22
2.6
0
Enable/Disable
V
IH
V
IL
t
D
0.7*V
DD
0.3*V
DD
200
±200
V
V
ns
uA
KOhm
MOhm
ms
°C
ps
ps
ps
ps
45
t
R
/t
F
100 ohms differential
50
0.3
55
0.7
%
ps
1.125
1.25
V
OH
V
OL
1.43
1.10
330
1.6
454
50
1.375
50
10
600
V
V
mV
mV
V
mV
uA
ps
Symbol
V
DD
I
DD
Min
Supply
3.135
2.375
Frequency
Typical
3.3
2.5
Maximum
3.465
2.625
60
Units
V
V
mA
MHz
ppm
f
N
80
±20, ±25, ±50, ±100
275.000
0.9
247
1. The VCC6 power supply pin should be filtered, eg, a 0.1 and 0.01uf capacitor.
2. See Standard Frequencies and Ordering Information for more information.
3. Includes calibration tolerance, operating temperature, supply voltage variations, aging and IR reflow.
4. Figure 2 defines these parameters and Figure 3 defines the test circuit.
5. Duty Cycle is defined as the On/Time Period.
6. Measured using an Agilent E5052, 155.520MHz. Please see “Typical Phase Noise and Jitter Report for the VCC6 series”.
7. Measured using a Wavecrest SIA3300C, 90K samples.
8. Outputs will be Enabled if Enable/Disable is left open.
50
50
Out
Out
0.01 uF
DC
6
1
5
2
4
3
Figure 3.
Page3
Package and Pinout
Table 3. Pinout
Pin #
1
2
3
4
5
6
Symbol
E/D or NC
E/D or NC
GND
f
O
Cf
O
V
DD
Function
Enable Disable or No Connection
Enable Disable or No Connection
Electrical and Lid Ground
Output Frequency
Complementary Output Frequency
Supply Voltage
Table 4. Enable Disable Function
(optional on pin 1 or pin2)
E/D Pin
High
Open
Low
Output
Clock Output
Clock Output
High Impedance
6
7.0±0.15
5
VCC6-XXX
XXXMXX
YYWW C
4
1.96
5.0±0.15
1
2
1.397
3
1.6 max
1.27
Marking
XXXMXXX = frequency
YY= Year
WW = Week
C = Country Code
Dimensions are in mm
2.54
1.78
3.66
1
6
2
Bottom View
5
3
3.57
4
2.54
5.08
5.08
Figure 4. Package Outline Drawing
Figure 5. Pad Layout
LVPECL Application Diagrams
140Ω
140Ω
Figure 6. Standard PECL Output Configuration Figure 7. Single Resistor Termination Scheme
Resistor values are typically 140 ohms for 3.3V
operation and 84 ohms for 2.5V operation.
Figure 8. Pull-Up Pull Down Termination
Resistor values are typically for 3.3V operation
For 2.5V operation, the resistor to ground is 62
ohms and the resistor to supply is 240 ohms
The VCC6 incorporates a standard PECL output scheme, which are un-terminated emitters as shown in Figure 6. There are numerous application notes on
terminating and interfacing PECL logic and the two most common methods are a single resistor to ground, Figure 7, and a pull-up/pull-down scheme as
shown in Figure 8. An AC coupling capacitor is optional, depending on the application and the input logic requirements of the next stage.
Page4
LVDS Application Diagrams
V
CC
LVDS
Driver
100
LVDS
Receiver
LVDS
Driver
100
Receiver
OUT+
OUT-
Figure 9. Standard LVDS
Output Configuration
Figure 10. LVDS to LVDS Connection, Internal 100ohm
Figure 11. LVDS to LVDS Connection
Some LVDS structures have an internal 100 ohm resistor
External 100ohm and AC blocking caps
on the input and do not need additional components.
Some input structures may not have an internal 100 ohm
resistor on the input and will need an external 100ohm
resistor for impedance matching. Also, the input may have
an internal DC bias which may not be compatible with
LVDS levels, AC blocking capacitors can be used.
One of the most important considerations is terminating the Output and Complementary Outputs equally. An unused output should not be left un-termi-
nated, and if one of the two outputs is left open it will result in excessive jitter on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to jitter related problems.
Environmental and IR Compliance
Table 5. Environmental Compliance
Parameter
Mechanical Shock
Mechanical Vibration
Temperature Cycle
Solderability
Fine and Gross Leak
Resistance to Solvents
Moisture Sensitivity Level
Contact Pads
ThetaJC (bottom of package)
Weight
Condition
MIL-STD-883 Method 2002
MIL-STD-883 Method 2007
MIL-STD-883 Method 1010
MIL-STD-883 Method 2003
MIL-STD-883 Method 1014
MIL-STD-883 Method 2015
MSL1
Gold (0.3 um min - 1.0 um max) over Nickel
13 C/W
170 mg
IR Compliance
S
Suggested IR Profile
Devices are built using lead free epoxy and can be subjected to
standard lead free IR refl
ow conditions shown in Table 5. Contact
pads are gold over nickel and lower maximum temperatures can also
In large power plants, the required DC load is relatively large, and the capacity of the battery is usually above 2000A·h. If a conventional 10A or 20A switching rectifier module is used, generally 20...
For the current LED light efficiency level, since about 80% of the input electrical energy is converted into heat and the LED chip area is small, chip heat dissipation is a key issue that must be solv...
Based on SOC application, a low-voltage, high-gain constant transconductance rail-to-rail operational amplifier IP core is designed and implemented using TSMC 0.18μm CMOS process. The operational ampl...
Determining the composition and quality of liquids is essential for many applications. The prime example is water, which is the world's most precious native resource. Water purification and water filt...
A biped robot joint constructed by pneumatic artificial muscles is introduced. The joint uses the flexible characteristics of pneumatic artificial muscles to effectively control the impact of the la...[Details]
This issue will briefly introduce the test related to spectrum - occupied bandwidth.
Definition: Occupied bandwidth refers to the bandwidth corresponding to 99% of the total transmitted power, cent...[Details]
Signal sources have developed to a very wide range today. We can classify them according to the frequency range: ultra-low frequency (0.1m～1kHz), audio (20Hz～20kHz), video (20kHz～10MHz), radio fre...[Details]
Abstract:
Using TMS320F2812 DSP chip as the control unit, without any gate control device control, the rich software resources of DSP 2812 are used to achieve equal precision measurement. A...[Details]
With the improvement of social automation, human-computer interaction capabilities urgently need a major change, and develop in a direction that is more convenient to use and more intuitive. Laser ...[Details]
0 Introduction
One of the basic tasks of machine vision is to obtain image information from the camera and calculate the geometric information of objects in three-dimensional space, so as ...[Details]
Abstract: This article introduces several floorplanning techniques for sub-65nm chip partitioning. These techniques help us complete a practical floorplan in a relatively short time, including: ana...[Details]
Fairchild Semiconductor provides the industry's smallest power management solution FAN5902 for 3G mobile phone and wireless data card designers. This RF power DC-DC converter uses a 12-bump 0.5mm p...[Details]
0 Introduction
The rapid development of wireless communication technology and video compression technology has made wireless video transmission a hot topic of research. Wireless video tran...[Details]
The dual-field-of-view infrared optical system can simultaneously provide two images with different magnifications and fields of view. The large field of view in the system has a lower resolution a...[Details]
Today, a new systematic maintenance approach can measure, locate and repair problems in rail and tram tracks in a timely manner. Combining mature railway engineering techniques with advanced techno...[Details]
1 Introduction
Fatigue driving is one of the main causes of traffic accidents. According to statistics, traffic accidents caused by driving fatigue are the highest in both absolute numbers...[Details]
O Introduction
Digital signal generator is a signal generating device and signal source widely used in electronic circuit design, automatic control system and instrument measurement, corre...[Details]
1 Introduction
As the requirements for the capacity and quality of power supply systems for high-end equipment in industries such as electricity, communications, aviation, large informatio...[Details]
0 Introduction
With the improvement of the automation level of industrial production in my country, more and more equipment needs to be monitored, operated and maintained in the field....[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
