Figure 7. Standard PECL Output Configuration Figure 8. Single Resistor Termination Scheme
Resistor values are typically 140 ohms for
3.3V operation.
Resistor values are typically 84 ohms for 2.5V
operation.
The VCC6 incorporates a standard PECL output scheme, which are un-terminated emitters as shown in Figure 7. There are numerous application notes on
terminating and interfacing PECL logic and the two most common methods are a single resistor to ground, Figure 8, and a pull-up/pull-down scheme as
shown in Figure 9. An AC coupling capacitor is optional, depending on the application and the input logic requirements of the next stage.
LVDS Application Diagrams
V
CC
LVDS
Driver
100
LVDS
Receiver
LVDS
Driver
100
Receiver
OUT+
OUT-
Figure 10 Standard LVDS
Output Configuration
Figure 11. LVDS to LVDS Connection, Internal 100ohm
Figure 12. LVDS to LVDS Connection
Some LVDS structures have an internal 100 ohm resistor on the
External 100ohm and AC blocking caps
input and do not need additional components.
Some input structures may not have an internal 100 ohm
resistor on the input and will need an external 100ohm
resistor for impedance matching. Also, the input may have
an internal DC bias which may not be compatible with
LVDS levels, AC blocking capacitors can be used.
One of the most important considerations is terminating the Output and Complementary Outputs equally. An unused output should not be left un-termi-
nated, and if one of the two outputs is left open it will result in excessive jitter on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to jitter related problems.
I used an oscilloscope to measure the P1.0 pin and observed the ACLK output. I found that the waveform was not a square wave, and the frequency kept changing from 8HZ to 26K. Could it be that my chip ...
Under WIN2000, I used DS to write a driver with interrupt No. 9 for an ISA card. I used SOFTICE to debug it. In INTOBJ, I saw that interrupt 39 was the interrupt service routine. I used idt 39 but cou...
STC12C5A60S2 is going to use a 32MHz active crystal oscillator. What changes are needed in the crystal oscillator circuit and reset circuit? This is the circuit I drew. The crystal is connected to XTA...
[color=#000][font=Arial, 宋体]I installed ccs3.3, and this problem occurred. Is it because the emulator cannot be used under win7 or what? Please help. [/font][/color]...
Human body information monitoring is an emerging field. People envision developing wireless electroencephalogram (EEG) monitoring equipment to diagnose epilepsy patients. Wearable wireless EEG can ...[Details]
This article discusses how to use an ultra-low-power RF transceiver chip from Zarlink Semiconductor for pacemakers, neurostimulators, drug pumps, and other such implantable medical devices t...[Details]
Maximize instrument utilization and reduce
test times
Increasing the throughput of automated test systems can improve efficiency. Using off-the-shelf tools (COTS) such as multicore proc...[Details]
Lithium-ion batteries have a high energy-to-weight and energy-to-volume ratio, no memory effect, can be recharged many times, have a long service life, and are becoming increasingly cheaper. A good...[Details]
From the moment AVS video was born, scientists and engineers have been working tirelessly to reduce the size of audio and video bitstreams. Various advanced video compression algorithms have emerge...[Details]
With the rapid development of network technology and information communication, network economy and knowledge economy are no longer the exclusive domains of IT and other high-tech industries. The i...[Details]
According to In-Stat/MDR, the number of mobile phones with Bluetooth capabilities will reach at least 300 million by 2005. One of the clear evidences of the increasing adoption of Bluetooth is that...[Details]
Abstract: This paper introduces the origin and new features of MP4, and introduces the core audio compression technology MPEG-2 AAC (Advanced Audio Coding) based on MP4. Finally, it briefly summari...[Details]
Abstract:
This paper introduces the excitation system designed for 3/3 phase double winding induction generator, which is composed of DSP and FPGA. The interface circuit of the control sys...[Details]
Billboards are information display terminals for the public, with a wide range of civil and commercial values. However, most of the information displayed on billboards is currently solidified in th...[Details]
When it comes to ATX power supply, people will think of two "classic" ICs: pulse width modulation chip TL494 and voltage comparator LM339. The new dedicated control chip AT2005B has the functions ...[Details]
Femtocell base stations are required to meet stringent requirements in terms of interference, compatibility testing between mobile devices and networks (such as ad hoc networks, handovers), and mee...[Details]
"Where am I? Where am I going? Where is he/she? How far is he/she from me?..." Do you often have such questions like me? In fact, who can deny that these are questions that we often think about, ev...[Details]
introduction
The latest embedded designs enable a multitude of complex new products and services across a wide range of industries and applications. Driven by shrinking cost constraints an...[Details]
0 Introduction
μClinux is an operating system for embedded control. It inherits most of the features of the Linux kernel and is designed for embedded microprocessors without a memory manag...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
