EEWORLDEEWORLDEEWORLD

Part Number

Search

SK250M10A7SQ1019

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 250V, 20% +Tol, 20% -Tol, 10uF, Through Hole Mount, ROHS COMPLIANT
CategoryPassive components    capacitor   
File Size61KB,3 Pages
ManufacturerYAGEO
Websitehttp://www.yageo.com/
Environmental Compliance  
Download Datasheet Parametric View All

SK250M10A7SQ1019 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 250V, 20% +Tol, 20% -Tol, 10uF, Through Hole Mount, ROHS COMPLIANT

SK250M10A7SQ1019 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerYAGEO
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
capacitance10 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
dielectric materialsALUMINUM (WET)
leakage current0.075 mA
Manufacturer's serial numberSG
Installation featuresTHROUGH HOLE MOUNT
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
Package shapeCYLINDRICAL PACKAGE
method of packingTR
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)250 V
ripple current100 mA
surface mountNO
Delta tangent0.15
Terminal shapeWIRE
YAGEO CORPORATION
ALUMINUM ELECTROLYTIC CAPACITORS
SG
[ Electronic Ballast ]
ELECTRICAL CHARACTERISTICS
Operating Temperature : -40 ~ +105°C / -25 ~ +105°C
Working Voltage : 160 ~ 400V / 450V
Rate Capacitance Range : 4.7 ~ 330µF / 3.3~100µF
Capacitance Tolerance : -20 ~ +20%
DC Leakage Current (µA) : I = 0.02 CV + 25
( After 2 Minute Application of DC Working Voltage at 25°C )
Dissipation Factor : at 120 Hz, 25°C
WV (V) : 160
200
250
350
400
450
D.F (%) : 15
15
15
20
24
24
For capacitor whose capacitance exceeds 1000µF. The value of D.F(%) is increased by 2% for every
addition of 1000µF.
Load Life : 5000 Hours at Assured with Full Rated Maximum Ripple Current Applied
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200% of Initial Requirement
(c) Leakage Current : Not Exceed the Initial Requirement
Shelf Life : Hours, No Voltage Applied
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200 % of Initial Requirement
(c) Leakage Current : Not Exceed 200% of Initial Requirement
Miniature Size Aluminum
Electrolytic Capacitors
Multiplier for Ripple Current
Frequency (Hz)
6.3~100V Below~68µF
50,60
0.80
120
1.00
300
1.20
1K 10K~100K
1.40
1.6
Temperature(°C)
Factor
65
1.70
85
1.40
105
1.00
DIAGRAM OF DIMENSIONS
4.0
5.0
6.3
8.0
10.0
12.0
13.0
16.0
18.0
22.0
F
1.5
2.0
2.5
3.5
5.0
0.5
0.5
Rubber Stand-off
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Vinyl Sleeve
(P.V.C)
Dimensions : mm
Rubber End Seal
F 0.5
F 0.5
0.6
L
0.4Max.
15Min.
5Min.
D 0.5
L
15Min.
5Min.
D 0.5
7.5
10.0
0.8
0.8
PIC32 comes with AD problem
I want to scan four channels, but I can only read one data at a time, which is the data of AN8. Please give me some advice. The code is below. The chip is PIC32MX564-128H void __ADC10SCAN() { uint a =...
hugong2 Microchip MCU
Anxious - low frequency frequency meter.
Can anyone help me write a low frequency frequency meter, which requires a four-digit digital tube display and two decimal places (50.00). Use external interrupt 0 to collect signals. It is best to us...
1614048761 51mcu
Motor stroke control problem
Currently, a servo motor is used to drive the device to slide, and it will stop at a fixed position. This is currently achieved by photoelectric switches, but one problem with photoelectric switches i...
elec32156 Motor Drive Control(Motor Control)
Help with the angle, acceleration conversion and accuracy of LSM6DSM
[color=#008000][backcolor=rgb(255, 255, 255)][font=Tahoma,]Excuse me, how to convert the linear velocity and angular velocity of the six-axis data collected into angle and acceleration? Can LSM6DSM su...
nemo_1995 MEMS sensors
How to set up CC2530 SPI communication?
I'm working on a board that needs to use CC2530 to collect the acceleration of ADXL345 via SPI, but the communication is not working. Can any expert tell me how to set up the SPI communication of CC25...
xingshui RF/Wirelessly
Experts, please give me some advice. This program detects sensor information for(i=0; i<8; i++) {flagSensor[i] = sensorDat...I don't understand?
/ 检测传感器信息if(g_enSensor) {len = read(fd_Sensor, &sensorData, sizeof(unsigned char));if(len > 0) {printf("sensorData is 0x%x ", sensorData);} else {perror("error to read fd_Sensor");exit(1);}}for(i=0; i...
hxf666 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2099  1678  2075  1125  1079  43  34  42  23  22 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号