• Phase-Lock Loop Clock Distribution for Applications ranging
from 10MHz to 133MHz operating frequency
• Distributes one clock input to two banks of four outputs
• Separate output enable for each output bank
• External feedback (FBK) pin is used to synchronize the outputs
to the clock input
• Output Skew <200 ps
• Low jitter <200 ps cycle-to-cycle
• 1x, 2x, 4x output options (see table):
– IDT2308A-1 1x
– IDT2308A-2 1x, 2x
– IDT2308A-3 2x, 4x
– IDT2308A-4 2x
– IDT2308A-1H and -2H for High Drive
• No external RC network required
• Operates at 3.3V V
DD
• Available in SOIC and TSSOP packages
DESCRIPTION:
The IDT2308A is a high-speed phase-lock loop (PLL) clock multiplier. It is
designed to address high-speed clock distribution and multiplication applica-
tions. The zero delay is achieved by aligning the phase between the incoming
clock and the output clock, operable within the range of 10 to 133MHz.
The IDT2308A has two banks of four outputs each that are controlled via two
select addresses. By proper selection of input addresses, both banks can be
put in tri-state mode. In test mode, the PLL is turned off, and the input clock
directly drives the outputs for system testing purposes. In the absence of an
input clock, the IDT2308A enters power down. In this mode, the device will
draw less than 12µA for Commercial Temperature range and less than 25µA
for Industrial temperature range, and the outputs are tri-stated.
The IDT2308A is available in six unique configurations for both pre-
scaling and multiplication of the Input REF Clock. (See available options
table.)
The PLL is closed externally to provide more flexibility by allowing the user
to control the delay between the input clock and the outputs.
The IDT2308A is characterized for both Industrial and Commercial opera-
tion.
FUNCTIONAL BLOCK DIAGRAM
(-3, -4)
FBK
REF
3
CLKA2
16
1
2
PLL
2
CLKA1
14
CLKA3
15
CLKA4
S2
S1
8
9
Control
Logic
(-2, -3)
2
6
CLKB1
7
CLKB2
10
CLKB3
11
CLKB4
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES
1
c
2012
Integrated Device Technology, Inc.
AUGUST 2012
DSC 6587/9
IDT2308A
3.3V ZERO DELAY CLOCK MULTIPLIER
COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES
PIN CONFIGURATION
ABSOLUTE MAXIMUM RATINGS
(1)
Symbol
V
DD
Rating
Supply Voltage Range
Input Voltage Range (REF)
Input Voltage Range
(except REF)
I
IK
(V
I
< 0)
I
O
(V
O
= 0 to V
DD
)
V
DD
or GND
T
A
= 55°C
(in still air)
(3)
T
STG
Operating
Temperature
Operating
Storage Temperature Range
Commercial Temperature
Range
Industrial Temperature
Range
-40 to +85
°C
–65 to +150
0 to +70
°C
°C
Continuous Current
Maximum Power Dissipation
±100
0.7
mA
W
Input Clamp Current
Continuous Output Current
Max.
–0.5 to +4.6
–0.5 to +5.5
–0.5 to
V
DD
+0.5
–50
±50
mA
mA
Unit
V
V
V
V
I (2)
V
I
REF
CLKA1
CLKA2
V
DD
GND
CLKB1
CLKB2
S2
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
FBK
CLKA4
CLKA3
V
DD
GND
CLKB4
CLKB3
S1
SOIC/ TSSOP
TOP VIEW
Temperature
PIN DESCRIPTION
Pin Number
REF
CLKA1
(1)
CLKA2
(1)
V
DD
GND
CLKB1
(1)
CLKB2
(1)
S2
(2)
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may
cause permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those indicated in the
operational sections of this specification is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect reliability.
2. The input and output negative-voltage ratings may be exceeded if the input and output
clamp-current ratings are observed.
3. The maximum package power dissipation is calculated using a junction temperature
of 150
°
C and a board trace length of 750 mils.
Functional Description
Input Reference Clock, 5 Volt Tolerant Input
Clock Output for Bank A
Clock Output for Bank A
3.3V Supply
Ground
Clock Output for Bank B
Clock Output for Bank B
Select Input, Bit 2
Select Input, Bit 1
Clock Output for Bank B
Clock Output for Bank B
Ground
3.3V Supply
Clock Output for Bank A
Clock Output for Bank A
PLL Feedback Input
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
APPLICATIONS:
•
•
•
•
•
SDRAM
Telecom
Datacom
PC Motherboards/Workstations
Critical Path Delay Designs
S1
(2)
CLKB3
(1)
CLKB4
(1)
GND
V
DD
CLKA3
(1)
CLKA4
(1)
FBK
NOTES:
1. Weak pull down on all outputs.
2. Weak pull ups on these inputs.
2
IDT2308A
3.3V ZERO DELAY CLOCK MULTIPLIER
COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES
FUNCTION TABLE
(1)
SELECT INPUT DECODING
S2
L
L
H
H
NOTE:
1. H = HIGH Voltage Level
L = LOW Voltage Level
S1
L
H
L
H
CLK A
Tri-State
Driven
Driven
Driven
CLK B
Tri-State
Tri-State
Driven
Driven
Output Source
PLL
PLL
REF
PLL
PLL Shut Down
Y
N
Y
N
AVAILABLE OPTIONS FOR IDT2308A
Device
IDT2308A-1
IDT2308A-1H
IDT2308A-2
IDT2308A-2
IDT2308A-2H
IDT2308A-2H
IDT2308A-3
IDT2308A-3
IDT2308A-4
Feedback From
Bank A or Bank B
Bank A or Bank B
Bank A
Bank B
Bank A
Bank B
Bank A
Bank B
Bank A or Bank B
Bank A Frequency
Reference
Reference
Reference
2 x Reference
Reference
2 x Reference
2 x Reference
4 x Reference
2 x Reference
Bank B Frequency
Reference
Reference
Reference/2
Reference
Reference/2
Reference
Reference or
Reference
(1)
2 x Reference
2 x Reference
NOTE:
1. Output phase is indeterminant (0° or 180° from input clock).
ZERO DELAY AND SKEW CONTROL
To close the feedback loop of the IDT2308A, the FBK pin can be driven from any of the eight available output pins. The output driving the FBK pin
will be driving a total load of 7pF plus any additional load that it drives. The relative loading of this output (with respect to the remaining outputs) can adjust
the input-output delay.
For applications requiring zero input-output delay, all outputs including the one providing feedback should be equally loaded. Ensure the outputs are
I was secretly sad because I didn't see a direct PWM module. Then the PWM in the timer does not have its own dead zone control. So I changed it to use timer for continuous timing and then flip the IO ...
I made a control board with MSP430G2553, one TM1640 chip for display, two 595 for display and relay control, but it can't pass the group pulse test. When the group pulse is applied, the display is all...
I have a strange problem. If I assign a signal in the circuit to an output pin, the logic of the whole circuit is wrong. (If it is not output, the logic is correct when observed through other pins.) H...
The rapid development of the Internet has realized high-speed information transmission and resource sharing, greatly facilitating people's lives. Embedded systems are widely used in various electr...[Details]
At present, the traffic congestion in cities is quite serious. According to relevant news reports: In China, the traffic congestion has expanded from megacities such as Beijing, Shanghai, and Guang...[Details]
0. Introduction
In daily life, we often see some special-purpose vehicles. When these vehicles pass through intersections, they often obtain the right of way at intersections by temporarily op...[Details]
There are three types of mobile TV: one is based on analog TV broadcasting network, another is based on mobile communication network, and the other is based on digital broadcasting network. The f...[Details]
introduction
Solar cells and LED lighting are typical applications of new energy and energy-saving and efficient technologies. Solar LED lighting uses solar cells to convert solar energy...[Details]
Toyohashi University of Technology demonstrated electric field coupled wireless power supply technology using life-size car tires and roads at the wireless technology exhibition "Wireless Technolog...[Details]
1. When the slip speed regulating motor is undergoing frequency conversion and energy saving transformation, the original excitation box (referred to as the speed regulating box) and the original s...[Details]
Fruit planting is an important part of China's agricultural development, and fruit tree pest control operations are becoming more and more important. At present, the overall level of pesticide applica...[Details]
LED is now known as the fourth generation of light sources. High-power LED has many advantages over traditional light sources in outdoor lighting.
1 LED lamps have high light efficiency
C...[Details]
This article focuses on closing the feedback loop of an isolated power supply using a TL431 shunt regulator. The article discusses a method to extend the bandwidth of the power supply control loop ...[Details]
The installation locations of DC-DC converters are relatively scattered. DC-DC converters can be found on the power board, main board, logic control board and other circuit boards of PDP color TVs....[Details]
In the TV monitoring system, in order to complete the collection of information from various information points (video, audio, alarm signal) and the control of various front-end devices (PTZ, lens,...[Details]
During the global semiconductor industry recession, the automotive electronics market has performed strongly, especially the application of car remote control systems has become more and more wides...[Details]
1 Features
1.1 Single cell operating voltage up to 3.7V
It is three times that of nickel-cadmium batteries and nickel-metal hydride batteries, and nearly twice that of lead-acid batteries...[Details]
1 Introduction
In order to cope with the energy crisis and slow down global warming, many countries have begun to pay attention to energy conservation and emission reduction and the de...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
