EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-MS2LC2841

Description
Transponder, 10709Mbps(Tx), 10709Mbps(Rx), LC/SPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerJDS Uniphase Corporation ( VIAVI )
Websitehttp://www.jdsu.com/index.html
Download Datasheet Parametric View All

PH1-MS2LC2841 Overview

Transponder, 10709Mbps(Tx), 10709Mbps(Rx), LC/SPC Connector,

PH1-MS2LC2841 Parametric

Parameter NameAttribute value
MakerJDS Uniphase Corporation ( VIAVI )
Reach Compliance Codecompliant
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body height13.2 mm
Body length or diameter84.1 mm
Communication standardsGR-253
Connection TypeLC/SPC CONNECTOR
Data rate (receive)10709 Mbps
Data rate (send)10709 Mbps
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1533 nm
Nominal optical power output0.562 mW
minimum return loss-27 dB
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
Disassembling a ROG
Last night I searched for laptop disassembly, but I didn't find any detailed disassembly pictures. The main reason was that other less expensive chips were not listed, only the more expensive chips we...
xutong Making friends through disassembly
s7200 problem SF/DIAG red light is on
When the 224 is running normally, the SF/DIAG light suddenly turns on, the input light turns on, and the output light does not turn on. What's going on? Thank you everyone....
eeleader Industrial Control Electronics
When will we open an A8 section?
When will we be able to open an A8 section?...
songhaifei Microcontroller MCU
[OpenCV Getting Started Tutorial 4] ROI Area Image Overlay & Primary Image Mixing Full Analysis
[i=s]This post was last edited by Rambo on 2017-12-19 17:20[/i] [align=left][color=#555555][font="][size=15px]In this article, we learned how to define the region of interest ROI in OpenCV, how to use...
兰博 Embedded System
stm8s207k6 multi-slave SPI function
Hello everyone:Since the NSS pin of stm8s207k6 is not a chip select pin, how can I realize the SPI communication function between a master and multiple slaves?Other MCUs have CS pins that can easily r...
天目 stm32/stm8
IGBT protection circuit using current sensor for overcurrent detection
[b][font=Verdana]IGBT protection circuit using current sensor for overcurrent detection[/font][/b] [img]http://www.dianlut.com/uploads/allimg/090513/2334355016-0.jpg[/img] [font=Verdana]Figure 8 is an...
eeleader Sensor

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1111  1834  2111  2664  1842  23  37  43  54  38 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号