Figure 7. Standard PECL Output Configuration Figure 8. Single Resistor Termination Scheme
Resistor values are typically 120 to 240 ohms
for 3.3V operation.
Resistor values are typically 82 to 120 ohms
for 2.5V operation.
Figure 9. Pull-Up Pull Down Termination
Resistor values are typically for 3.3V operation
For 2.5V operation, the resistor to ground is 62
ohms and the resistor to supply is 240 ohms
The VCC6 incorporates a standard PECL output scheme, which are un-terminated emitters as shown in Figure 7. There are numerous application notes on
terminating and interfacing PECL logic and the two most common methods are a single resistor to ground, Figure 8, and a pull-up/pull-down scheme as
shown in Figure 9. An AC coupling capacitor is optional, depending on the application and the input logic requirements of the next stage.
LVDS Application Diagrams
V
CC
LVDS
Driver
100
LVDS
Receiver
LVDS
Driver
100
Receiver
OUT+
OUT-
Figure 10 Standard LVDS
Output Configuration
Figure 11. LVDS to LVDS Connection, Internal 100ohm
Figure 12. LVDS to LVDS Connection
Some LVDS structures have an internal 100 ohm resistor on the
External 100ohm and AC blocking caps
input and do not need additional components.
Some input structures may not have an internal 100 ohm
resistor on the input and will need an external 100ohm
resistor for impedance matching. Also, the input may have
an internal DC bias which may not be compatible with
LVDS levels, AC blocking capacitors can be used.
One of the most important considerations is terminating the Output and Complementary Outputs equally. An unused output should not be left un-termi-
nated, and if it one of the two outputs is left open it will result in excessive jitter on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to jitter related problems.
[i=s]This post was last edited by paulhyde on 2014-9-15 09:29[/i]I saw a lot of posts by Mr. Huang Zhiwei in the competition section. . . Very impressive. . .Looking forward to Mr. Huang Zhiwei's anal...
1. Are the ARM boot code and bootloader the same thing? 2. Do general ARM chips have boot code fixed when they leave the factory? If so, why do users still need to write a boot program?...
4.1. The basic framework of the MMC subsystem 4.1.1. The code of the MMC subsystem is in kernel/driver/MMC. Currently, the MMC subsystem supports some forms of memory cards: SD, SDIO, MMC. 4.1.2. HOST...
Human body information monitoring is an emerging field. People envision developing wireless electroencephalogram (EEG) monitoring equipment to diagnose epilepsy patients. Wearable wireless EEG can ...[Details]
Designers of hearing aids have stringent requirements. Hearing aids must be small enough to fit in or behind the ear, operate on ultra-low power, and be free of noise or distortion. To meet these requ...[Details]
This article introduces a miniature home electrocardiograph. The instrument has powerful functions: display monitoring, storage, playback, printing, record management, power alarm, telephone or Intern...[Details]
Emulation Features
Emulation provides a set of standard operations for integration and debugging. Some of its main features are as follows:
BreakpointsA
common feature of emulatio...[Details]
Portable devices with audio functions (such as portable media players and multimedia mobile phones) require long audio playback time, that is, long battery life. To extend the battery life of port...[Details]
The overcurrent and overheating coordinated protection technology implemented by polymer positive temperature coefficient devices (PPTC) can protect motors, controllers and electronic components in...[Details]
1 Introduction
The intelligent meter reading system is a system that reads the data of multiple user meters in a centralized manner through the transmission media by the master station. It...[Details]
Introduction
Wireless operators are driving demand for broadband and data rates by offering enhanced data services to increase average revenue per user (ARPU). The need to provide users with ...[Details]
1. Introduction
Rolling bearings are the most widely used general mechanical components in various rotating machines. Whether their operating status is normal often directly affects the perfo...[Details]
Introduction
As a kind of biometric identification, fingerprint recognition has incomparable advantages in identity recognition over other means: human fingerprints are unique and stable; wit...[Details]
Abstract:
Aiming at the problems of repeated design and high cost of existing LED large-screen displays, a modular LED large-screen display is proposed, which can realize flexible configurati...[Details]
Abstract:
A single pulse secondary radar reply processor implemented with EPLD. Its main functions include: reply frame pulse detection, reply information decoding, assembling reply inf...[Details]
IntroductionUSB
, serial port, and parallel port are commonly used interfaces for communication between PC and peripherals. However, for images with large data volumes, if the serial RS-232 protoc...[Details]
1 Introduction
In recent years, with the rapid growth of mobile phones and MP4 video players, it is estimated that the production of mobile phones this year will reach 1 billion units, and...[Details]
1. Intrusion Detection System (IDS)
IDS is the abbreviation of "Intrusion Detection Systems" in English, which means "Intrusion Detection System" in Chinese. Professionally speaking, it monito...[Details]
NXP MCU
京公网安备 11010802033920号
EEWORLD
