Figure 7. Standard PECL Output Configuration Figure 8. Single Resistor Termination Scheme
Resistor values are typically 140 ohms for
3.3V operation.
Resistor values are typically 84 ohms for 2.5V
operation.
The VCC6 incorporates a standard PECL output scheme, which are un-terminated emitters as shown in Figure 7. There are numerous application notes on
terminating and interfacing PECL logic and the two most common methods are a single resistor to ground, Figure 8, and a pull-up/pull-down scheme as
shown in Figure 9. An AC coupling capacitor is optional, depending on the application and the input logic requirements of the next stage.
LVDS Application Diagrams
V
CC
LVDS
Driver
100
LVDS
Receiver
LVDS
Driver
100
Receiver
OUT+
OUT-
Figure 10 Standard LVDS
Output Configuration
Figure 11. LVDS to LVDS Connection, Internal 100ohm
Figure 12. LVDS to LVDS Connection
Some LVDS structures have an internal 100 ohm resistor on the
External 100ohm and AC blocking caps
input and do not need additional components.
Some input structures may not have an internal 100 ohm
resistor on the input and will need an external 100ohm
resistor for impedance matching. Also, the input may have
an internal DC bias which may not be compatible with
LVDS levels, AC blocking capacitors can be used.
One of the most important considerations is terminating the Output and Complementary Outputs equally. An unused output should not be left un-termi-
nated, and if one of the two outputs is left open it will result in excessive jitter on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to jitter related problems.
[i=s]This post was last edited by paulhyde on 2014-9-15 09:29[/i]I saw a lot of posts by Mr. Huang Zhiwei in the competition section. . . Very impressive. . .Looking forward to Mr. Huang Zhiwei's anal...
1. Are the ARM boot code and bootloader the same thing? 2. Do general ARM chips have boot code fixed when they leave the factory? If so, why do users still need to write a boot program?...
4.1. The basic framework of the MMC subsystem 4.1.1. The code of the MMC subsystem is in kernel/driver/MMC. Currently, the MMC subsystem supports some forms of memory cards: SD, SDIO, MMC. 4.1.2. HOST...
Project Overview
The micro urine analyzer we designed can detect ten parameters of urine, including white blood cells, nitrite, urobilinogen, protein, pH value, occult blood, specific g...[Details]
【
Abstract
】
RFID technology will be ubiquitous in the future, and there is no doubt about it, because it brings convenience and timeliness to people, which means efficiency and...[Details]
The role of digital-to-analog converters
Real-world analog signals, such as temperature, pressure, sound, or images, are constantly being converted into digital form that is easier to store, p...[Details]
With the rapid development of digital technology, various digital display screens have emerged, including LED, LCD, DLP, etc. There are various control systems for various digital large screens, in...[Details]
This summary will introduce the transmitter characteristic test of TD terminal products - uplink power control. According to the 3GPP TS34.122 standard, UE uplink power control is divided into uplink ...[Details]
1 Introduction
In the current test field, the correlation detection method is increasingly widely used for filtering. Correlation filtering can easily separate a signal of a specific frequency...[Details]
0Introduction
In oil drilling, accurate measurement of wellbore posture is the premise of wellbore trajectory control. To this end, this paper fully combines the advantages of single-chip ...[Details]
Chapter 1 Proposal
Endless salespeople interrupt your normal work schedule;
Employees leave their work stations without permission during working hours;
Unauthorized persons ente...[Details]
Introduction
The home ECG and blood pressure monitoring system consists of a data acquisition and recording device and a host computer electronic medical record management system. Therefor...[Details]
Electrocardiogram is an important means of diagnosing heart disease. However, due to various reasons, it is difficult to capture abnormal electrocardiograms with ordinary electrocardiographs. Although...[Details]
Application of TWLA500 in ADC and related fields
FAE: On-site technical support. Provide technical support to customers on the application of the products you sell, and handle quality ...[Details]
Anyone who has owned a laptop computer will have noticed that when running on battery power, their portable device behaves differently than when running on AC mains power—the display dims, the proc...[Details]
Fieldbus is an open, digital, multi-point communication control system local area network, and is one of the most promising technologies in today's automation field. CAN bus is a hot application in fi...[Details]
The PIC series 8-bit single-chip microcomputer (RISC microcontroller) developed by Microchip Technology Inc. in the United States, especially the microcontroller with built-in second-generation Flash ...[Details]
Abstract:
The signal flow of the external transceiver in the WCDMA/TD-SCDMA protocol is analyzed. The analysis results show that most of the functional modules in the WCDMA/TD-SCDMA external tr...[Details]
NXP MCU
京公网安备 11010802033920号
EEWORLD
