EEWORLDEEWORLDEEWORLD

Part Number

Search

REG101NA-2.5/250

Description
Fixed Positive LDO Regulator, 2.5V, 0.13V Dropout, NMOS, PDSO5, SOT-23, 5 PIN
CategoryPower/power management    The power supply circuit   
File Size226KB,13 Pages
ManufacturerBurr-Brown
Websitehttp://www.burr-brown.com/
Download Datasheet Parametric View All

REG101NA-2.5/250 Overview

Fixed Positive LDO Regulator, 2.5V, 0.13V Dropout, NMOS, PDSO5, SOT-23, 5 PIN

REG101NA-2.5/250 Parametric

Parameter NameAttribute value
MakerBurr-Brown
package instructionSOT-23, 5 PIN
Reach Compliance Codeunknown
Maximum drop-back voltage 10.13 V
Maximum input voltage10 V
Minimum input voltage3.1 V
JESD-30 codeR-PDSO-G5
Number of functions1
Number of terminals5
Working temperatureTJ-Max85 °C
Working temperature TJ-Min-40 °C
Maximum output current 10.1 A
Maximum output voltage 12.5675 V
Minimum output voltage 12.4325 V
Nominal output voltage 12.5 V
Package body materialPLASTIC/EPOXY
Package shapeRECTANGULAR
Package formSMALL OUTLINE
Certification statusNot Qualified
Regulator typeFIXED POSITIVE SINGLE OUTPUT LDO REGULATOR
surface mountYES
technologyNMOS
Terminal formGULL WING
Terminal locationDUAL
REG101
REG
101
www.ti.com
DMOS
100mA Low Dropout Regulator
FEATURES
q
NEW DMOS TOPOLOGY:
Ultra Low Dropout Voltage:
60mV typ at 100mA
Output capacitor NOT required for stability
q
FAST TRANSIENT RESPONSE
q
VERY LOW NOISE: 23
µ
Vrms
q
HIGH ACCURACY:
±
1.5% max
q
HIGH EFFICIENCY:
I
GND
= 500
µ
A at I
OUT
= 100mA
Not Enabled: I
GND
= 10nA
q
2.5V, 2.8V, 2.85V, 3.0V, 3.3V, 5.0V AND
ADJUSTABLE OUTPUT VERSIONS
q
OTHER OUTPUT VOLTAGES AVAILABLE
UPON REQUEST
q
FOLDBACK CURRENT LIMIT
q
THERMAL PROTECTION
q
SMALL SURFACE-MOUNT PACKAGES:
SOT23-5 and SO-8
DESCRIPTION
The REG101 is a family of low noise, low dropout
linear regulators with low ground pin current. Its new
DMOS topology provides significant improvement
over previous designs, including low dropout voltage
(only 60mV typ at full load), and better transient
performance. In addition, no output capacitor is re-
quired for stability, unlike conventional low dropout
regulators that are difficult to compensate and require
expensive low ESR capacitors greater than 1µF.
Typical ground pin current is only 500µA (at I
OUT
=
100mA) and drops to 10nA when not enabled mode.
Unlike regulators with PNP pass devices, quiescent
current remains relatively constant over load variation
and under dropout conditions.
The REG101 has very low output noise (typically
23µVrms for V
OUT
= 3.3V with C
NR
= 0.01µF),
making it ideal for use in portable communications
equipment. Accuracy is maintained over temperature,
line, and load variations. Key parameters are guaran-
teed over the specified temperature range
(–40°C to +85°C).
The REG101 is well protected—internal circuitry pro-
vides a current limit which protects the load from
damage. Thermal protection circuitry keeps the chip
from being damaged by excessive temperature. The
REG101 is available in the SOT23-5 and the SO-8
packages.
APPLICATIONS
q
q
q
q
q
q
PORTABLE COMMUNICATION DEVICES
BATTERY-POWERED EQUIPMENT
PERSONAL DIGITAL ASSISTANTS
MODEMS
BAR-CODE SCANNERS
BACKUP POWER SUPPLIES
Enable
V
IN
+
0.1µF
REG101
(Fixed Voltage
Versions)
Gnd
+
V
OUT
C
OUT(1)
V
IN
Enable
V
OUT
+
0.1µF
REG101-A
R
1
Adj
Gnd
NOTE: (1) Optional.
R
2
+
C
OUT(1)
NR
NR = Noise Reduction
Copyright © 2000, Texas Instruments Incorporated
SBVS026A
Printed in U.S.A. December, 2000
How does this function write half a byte to the LCD?
void DispDataWrOneNibble (CPU_INT08U data){ CPU_INT32U value; BSP_LCD_DISP_RW_LO();/* Set R/W write LOW to write to the LCD module.*/ BSP_LCD_DISP_E_HI();/* Write the UPPER nibble to the LCD module.*/...
Study_Stellaris Microcontroller MCU
Seeing this nW-class timer, I wonder if using it as a wake-up clock would be more power-efficient than the 430 internal clock.
This should be considered a traditional device, just a timer (1-64s), so you don't have to be surprised. The power consumption is 30nA, which I think I can't test. Below are the basic parameters. The ...
wstt Microcontroller MCU
I need help with the reading and writing of TWI of ATMEGA16. Please help me, AVR experts
Only the writing function of TWI is tested, and the device address, register address and data are written respectively. However, only the device address and data are seen from the oscilloscope, and th...
六弦蓝大宝 Microchip MCU
How to set the column names in the AD summer library component interface? Why are there only component names and footprints?
I right-clicked on the column name, selected columns, and added description and library myself. It worked at the time, but why did I close the software and reopen it, and the "description and library"...
自由女神 Embedded System
WBBSW Silk Screen
What does this silk screen printing WBBSW mean? It looks like a transistor. Is there any kind person who has silk screen reverse lookup information that can be sent to me?...
tangwei8802429 Analog electronics
Arrival of important components
I bought a resistive touch screen, 240*320 resolution, ILI9341 driver, I will light it up later and transplant emwin...
dql2016 DIY/Open Source Hardware

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2673  135  383  2923  1041  54  3  8  59  21 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号