Vin=28V dc ±5%, Iout=40A, CL=0µF, free running (see Note 10)
unless otherwise specified
Technical Specification
Group A
Subgroup
1
1
1
1
1
1
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
See Note 5
See Note 5
See Note 5
1, 2, 3
See Note 5
1, 2, 3
See Note 5
1, 2, 3
75
0.8
80
2
3.2
4.0
20
4.5
Current drain required to ensure module is off
Imax drawn from pin allowed, module on
See Figure A
2800
440
79
10
3
Hrs.
10
3
Hrs.
g
Electrical Characteristics Notes
1. Converter will undergo input over-voltage shutdown.
2. Derate output power to 50% of rated power at Tcase = 135ºC. 135ºC is above specified operating range.
3. High or low state of input voltage must persist for about 200µs to be acted on by the lockout or shutdown circuitry.
4. Current limit inception is defined as the point where the output voltage has dropped to 90% of its nominal value.
5. Parameter not tested but guaranteed to the limit specified.
6. Load current transition time ≥ 10µs.
7. Settling time measured from start of transient to the point where the output voltage has returned to ±50mV of its final value.
8. Line voltage transition time ≥ 100µs.
9. Input voltage rise time ≤ 250µs.
10. Operating the converter at a synchronization frequency above the free running frequency will cause the converter’s efficiency to be slightly reduced and it
may also cause a slight reduction in the maximum output current/power available. For more information consult the factory.
11. After a disable or fault event, module is inhibited from restarting for 300ms. See Shut Down section of the Control Features description.
12. SHARE pin outputs a power failure warning pulse during a fault condition. See Current Share section of the Control Features description.
13. Only the ES and HB grade products are tested at three temperatures. The C- grade products are tested at one temperature. Please refer to the
Construction and Environmental Stress Screening Options table for details.
14. These derating curves apply for the ES and HB grade products. The C- grade product has a maximum case temperature of 70ºC and a maximum junction
temperature rise of 20ºC above T
CASE
.
15. The specified operating case temperature for ES grade products is -45ºC to 100ºC. The specified operating case temperature for C- grade
products is 0ºC to 70ºC.
Product# MQFL-28-1R5S
Phone 1-888-567-9596
www.SynQor.com
Doc.# 005-2MQ1R5S Rev. C
10/24/13
Page 4
MQFL-28-1R5S
Output:
1.5V
Current:
40A
Technical Figures
100
95
90
100
95
90
Efficiency (%)
Efficiency (%)
16 Vin
28 Vin
40 Vin
0
5
10
15
20
25
30
35
40
85
80
75
70
65
60
85
80
75
70
65
60
-55ºC
25ºC
125ºC
16 Vin
28 Vin
40 Vin
Load Current (A)
Case Temperature (ºC)
Figure 1: Efficiency at nominal output voltage vs. load current for
minimum, nominal, and maximum input voltage at Tcase=25°C.
20
18
16
Figure 2: Efficiency at nominal output voltage and 60% rated power vs.
case temperature for input voltage of 16V, 28V, and 40V.
16
14
Power Dissipation (W)
14
12
10
8
6
4
2
0
0
5
10
15
20
25
30
35
40
16 Vin
28 Vin
40 Vin
Power Dissipation (W)
12
10
8
6
4
2
0
-55ºC
25ºC
125ºC
16 Vin
28 Vin
40 Vin
Load Current (A)
Case Temperature (ºC)
Figure 3: Power dissipation at nominal output voltage vs. load current
for minimum, nominal, and maximum input voltage at Tcase=25°C.
50
45
40
35
75
68
60
Figure 4: Power dissipation at nominal output voltage and 60% rated
power vs. case temperature for input voltage of 16V, 28V, and 40V.
1.8
1.6
1.4
Pout (W)
Iout (A)
30
25
20
15
10
5
0
25
45
65
85
105
125
= 105ºC
= 125ºC
= 145ºC
45
38
30
23
15
8
0
145
Output Voltage (V)
53
1.2
1
0.8
0.6
0.4
0.2
0
0
5
10
15
28 Vin
Case Temperature (ºC)
Load Current (A)
20
25
30
35
40
45
50
Figure 5: Output Current / Output Power derating curve as a function of
Tcase and the Maximum desired power MOSFET junction temperature
at Vin = 28V (see Note 14).
Product# MQFL-28-1R5S
Phone 1-888-567-9596
Figure 6: Output voltage vs. load current showing typical current limit
The microcontroller is a digital system. Each logic part has a corresponding threshold level and noise tolerance. As long as the external noise does not exceed the tolerance value of the logic element...
The schematic diagram is referenced from the Internet. The 38k square wave is generated by a function signal generator. There is no signal at the receiving head. I don’t know what went wrong?...
[font=微软雅黑][size=4]Welcome the New Year, celebrate the New Year, and celebrate the New Year. ADI's 19th prize-winning download event will celebrate the New Year with you! [/size][/font]{:1_107:} [font...
Please help me, thanks. The problem is as follows: Platform: wince 6.0 + arm9 (the company's own SOC) Camera OV7680 and OV2650, both support the test application in the ce private directory, can previ...
Our company is a WAVECOM agent providing technical (software/hardware) support and DEMO. Contact information: QQ:1109321905 (please specify) 13554943187 Kavin (Zhong Qingfu)...
PV DC fuses are safety devices used to protect PV panels, inverters, and DC loads. To ensure their safety and reliability, they must be UL248 certified.
Before applying for UL248 certifi...[Details]
A line scan lens is an industrial lens used with line scan cameras. Its imaging principle is to capture the image of the workpiece using a linear sensor and then perform digital signal processing t...[Details]
1. Project Overview
1.1 Introduction
Currently, most music files are saved in MP3 format, a lossy audio compression format that cannot perfectly reproduce the original music. With the exp...[Details]
Electric vehicles are currently gaining momentum, but this is just a facade. Fuel-powered vehicles remain unchallenged. While electric vehicles boast unique advantages in environmental emissions an...[Details]
1. Introduction
Electronic scales are gradually replacing traditional measuring tools like springs and balances in everyday life, such as electronic price computing scales and electronic weigh...[Details]
With the rapid advancement of automation technology, collaboration between robots is no longer just science fiction. Imagine dozens of machines moving goods in a warehouse without interfering with ...[Details]
1 Source of creativity
With the further development of electronic technology, electronic pets have gradually entered people's family life. At present, there are two main categories of relative...[Details]
With the development of science, the use of variable frequency technology is becoming more and more widespread, and it is used in both industrial equipment and household appliances. Inverter air co...[Details]
UPS stands for Uninterruptible Power Supply, which includes energy storage devices. It is mainly used to provide uninterruptible power supply for devices that require high power stability.
...[Details]
According to Nikkei, Japan has performed poorly in responding to China's power semiconductor challenges.
There are five major companies in Japan's power chip market: Mitsubishi Electric,...[Details]
In daily life, power transformers have different functions and uses due to different usage scenarios. The most common ones can be divided into: control transformers, isolation transformers, rectifi...[Details]
On August 20, Geely announced its focus on "One Cockpit". Through a unified AI OS architecture, a unified AI Agent, and a unified user ID, it will achieve an All-in-One AI cockpit, create the first...[Details]
Most cameras on the market use chips manufactured by Japanese companies like Sony, Sharp, Panasonic, and LG. South Korea now has the capability to produce chips, but the quality is somewhat inferio...[Details]
In this final installment of a five-part blog series, I will discuss noise in op amps driving headphone loads and some techniques for reducing it. Previous posts have discussed headphone load power...[Details]
As the power density of modern electronic systems continues to increase, effective thermal management has become critical to ensuring system performance, reliability, and longevity—especially in hi...[Details]
ARM Technology
京公网安备 11010802033920号
EEWORLD
