Internally synchronized registered outputs eliminate the
need to control
OE
Single R/W (READ/WRITE) control pin
Positive clock-edge triggered address, data, and control
signal registers for fully pipelined applications
4-word burst capability (interleaved or linear)
Individual byte write (BW
1
-
BW
4
) control (May tie active)
Three chip enables for simple depth expansion
Single 3.3V power supply (±5%)
Packaged in a JEDEC standard 100-pin TQFP package
clock cycle, and two cycles later its associated data cycle occurs, be it
read or write.
The IDT71V546 contains data I/O, address and control signal regis-
ters. Output enable is the only asynchronous signal and can be used to
disable the outputs at any given time.
A Clock Enable (CEN) pin allows operation of the IDT71V546 to be
suspended as long as necessary. All synchronous inputs are ignored
when
CEN
is high and the internal device registers will hold their previous
values.
There are three chip enable pins (CE
1
, CE
2
,
CE
2
) that allow the user
to deselect the device when desired. If any one of these three is not active
when ADV/LD is low, no new memory operation can be initiated and any
burst that was in progress is stopped. However, any pending data
transfers (reads or writes) will be completed. The data bus will tri-state two
cycles after the chip is deselected or a write initiated.
The IDT71V546 has an on-chip burst counter. In the burst mode, the
IDT71V546 can provide four cycles of data for a single address presented
to the SRAM. The order of the burst sequence is defined by the
LBO
input
pin. The
LBO
pin selects between linear and interleaved burst sequence.
The ADV/LD signal is used to load a new external address (ADV/LD =
LOW) or increment the internal burst counter (ADV/LD = HIGH).
The IDT71V546 SRAM utilizes IDT's high-performance, high-volume
3.3V CMOS process, and is packaged in a JEDEC standard 14mm x
20mm 100- pin thin plastic quad flatpack (TQFP) for high board density.
◆
◆
◆
◆
◆
◆
◆
◆
◆
◆
◆
Description
The IDT71V546 is a 3.3V high-speed 4,718,592-bit (4.5 Megabit)
synchronous SRAM organized as 128K x 36 bits. It is designed to
eliminate dead bus cycles when turning the bus around between reads
and writes, or writes and reads. Thus it has been given the name ZBT
TM
,
or Zero Bus Turn-around.
Address and control signals are applied to the SRAM during one
Pin Description Summary
A
0
- A
16
CE
1
, CE
2
,
CE
2
OE
R/W
CEN
BW
1
,
BW
2
,
BW
3
,
BW
4
CLK
ADV/LD
LBO
I/O
0
- I/O
31
, I/O
P1
- I/O
P4
V
DD
V
SS
Address Inputs
Three Chip Enables
Output Enable
Read/Write Signal
Clock Enable
Individual Byte Write Selects
Clock
Advance Burst Address / Load New Address
Linear / Interleaved Burst Order
Data Input/Output
3.3V Power
Ground
Input
Input
Input
Input
Input
Input
Input
Input
Input
I/O
Supply
Supply
Synchronous
Synchronous
Asynchronous
Synchronous
Synchronous
Synchronous
N/A
Synchronous
Static
Synchronous
Static
Static
3821 tbl 01
ZBT and Zero Bus Turnaround are trademarks of Integrated Device Technology, Inc. and the architecture is supported by Micron Technology and Motorola Inc.
Switching power supply design 1 The design of electronic products, especially military voltage-stabilized power supplies, is a systematic project. It not only needs to consider the parameter design , ...
Set socket timeout. Use select to succeed. Now I want to use setsockopt to set it, without select int nTimeOutRecv; /*socket is created correctly*/ ..... /*bind succeeds*/ ..... nTimeOutRecv = 1000; /...
Tracealyzer is a tracing and visualization analysis tool for RTOS systems, providing unprecedented insight into the behavior of the system at runtime. Problems that used to take days or even longer to...
I don't understand the macro dtom in mbuf in "TCP/IP Detailed Explanation Volume 2". The macro is defined like this: /* dtom(x) - convert data pointer within mbuf to mbuf pointer (XXX) */ #define dtom...
This article introduces how to design an interface on the OLED display screen of the RVB2601 development board based on the LVGL library.
The RVB2601 development board has a built-in monochrome OLED d...
This article discusses how to wake up a touch-sensitive device such as a tablet without touching the device, using basic gesture recognition and novel proximity sensors. The article discusses the p...[Details]
Microcontrollers (MCUs), which are widely used in automotive electronics, are rapidly facing time and cost pressures. The main advantage of using MCUs has always been to create high-level system in...[Details]
With the continuous improvement of the requirements of intelligent building security systems and the continuous improvement of people's safety awareness, indoor anti-theft has gradually attracted peop...[Details]
A multi-point temperature control heating control system was designed using the SST89E564RC single-chip microcomputer and a new temperature measuring device. The heating system can be controlled in...[Details]
my country is a big country in agriculture, grain production and consumption. Grains are a necessary condition for our nation to survive and develop. The flour processing industry will exist forever w...[Details]
12v Lead Acid batteries used in trucks, cars, RVs and uninterruptible power supplies are usually rated at 12V. This circuit monitors the battery, the charge and discharge curves, gives the cu...[Details]
This paper designs a 16x16LED Chinese character display bar based on single-chip dynamic scanning control, briefly analyzes the principle of Chinese character display, and studies how the LED displ...[Details]
Capacitance Measurement
Used to verify that capacitors meet the manufacturer's specifications. For quality control, a group of capacitors may be placed in an environmental chamber and the cap...[Details]
Introduction
Automakers are working to reduce vehicle weight to reduce CO2 emissions and improve fuel efficiency. Designers are therefore seeking new technologies and design techniques that can...[Details]
LED technology has made rapid progress, and improvements in chip design and materials have promoted the development of brighter and more durable light sources, and the scope of light source applica...[Details]
0 Introduction
High-precision current source can provide high-precision current supply for precision instruments, and is suitable for automatic measurement tasks of various resistors in semico...[Details]
1. Overview
At present, an information revolution is in the ascendant around the world, led by microelectronics, computers and communication technologies, and centered on information technolog...[Details]
1 Introduction
With the improvement of people's quality of life, lamps are no longer just basic indoor lighting tools, but also a kind of practical art for architectural decoration. When ther...[Details]
introduction
Steam turbines are driven by high-temperature and high-pressure steam generated by boilers to run at high speed. They are key power equipment in thermal power plants. The emergenc...[Details]
The invention of the steam engine ushered in the first conversion of internal energy and mechanical energy for mankind, and the birth of the internal combustion engine at the end of the 19th centur...[Details]
Power technology
京公网安备 11010802033920号
EEWORLD
