EEWORLDEEWORLDEEWORLD

Part Number

Search

BUS-63128-290Y

Description
Line Driver, 2 Driver, Hybrid, MDFP36,
CategoryAnalog mixed-signal IC    Drivers and interfaces   
File Size124KB,16 Pages
ManufacturerData Device Corporation
Download Datasheet Parametric View All

BUS-63128-290Y Overview

Line Driver, 2 Driver, Hybrid, MDFP36,

BUS-63128-290Y Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
MakerData Device Corporation
Reach Compliance Codecompliant
ECCN codeEAR99
Differential outputYES
Number of drives2
Interface integrated circuit typeLINE DRIVER
JESD-30 codeR-MDFP-F36
JESD-609 codee0
Number of terminals36
Maximum operating temperature70 °C
Minimum operating temperature
Package body materialMETAL
encapsulated codeDFP
Encapsulate equivalent codeFL36,.8,100
Package shapeRECTANGULAR
Package formFLATPACK
Peak Reflow Temperature (Celsius)NOT SPECIFIED
power supply5,-12 V
Certification statusNot Qualified
Maximum receive delay
surface mountYES
technologyHYBRID
Temperature levelCOMMERCIAL
Terminal surfaceTin/Lead (Sn/Pb)
Terminal formFLAT
Terminal pitch2.54 mm
Terminal locationDUAL
Maximum time at peak reflow temperatureNOT SPECIFIED
BUS-63100 SERIES
MIL-STD-1553 DATA BUS
SINGLE AND DUAL TRANSCEIVERS
BUS-63102
BUS-63105
BUS-63125
DESCRIPTION
The BUS-63100 transceivers are
complete transmitter and receiver
pairs conforming fully to MIL-STD-
1553A and 1553B. Features available
with selected models of this high reli-
ability series include: Smiths and
Harris interface type choices,
+12 V/+15 V power supply voltage
range, variable threshold levels, and
single (24-pin DDIP or square) and
completely independent dual redun-
dant (36-pin DDIP) packaging config-
urations. All models are also available
in flat packs.
The receiver section of the BUS-
63100 series accepts phase-modula-
ted bipolar data from a MIL-STD-1553
Data Bus and produces TTL signal
data at its outputs: RX Data Out and
RX Data Out. These outputs repre-
sent positive and negative variations
of the input data signals beyond an
internally fixed or externally set
threshold level. An external STROBE
input enables or disables the receiver
outputs.
The transmitter section accepts bipo-
lar TTL signal data at its TX Data and
TX Data input lines and produces
phase modulated bipolar data at the
TX Data and TX Data outputs. The
transmitters’ output voltage level is
typically 28 Vpp to 30 Vpp. An exter-
nal input, INHIBIT, takes priority over
the transmitter inputs and disables
the transmitter when activated with a
logic “1.”
The small size and different model
capabilities available with the
BUS-63100 series simplify engineer-
ing design, making it an excellent
choice for interfacing with any
MIL-STD-1553 system.
FEATURES
Conforms Fully to MIL-STD-1553A
and 1553B
Some Models Available to Military
(DESC) Drawings
Model Capabilities:
Single or Dual Redundant
Packaging
-12 V/-15 V Power Supply Voltage
Range Available
Harris or Smith’s I/O Compatibility
Small Size:
Single – 24-Pin DDIP or Square
Dual – 36-Pin DDIP Flat Packs
Low Power
High Reliability – LSI
±V
1553
DATA
BUS
+5 V
RECEIVER STROBE
BI PHASE
TTL DATA
PHASE MODULATED
BIPOLAR DATA
RX Data In
SHORT OR
LONG STUB
COUPLING
ISOLATION
TRANSFORMER
RX Data In
RECEIVER SECTION
COMPARATOR
RX Data
LIMITER
FILTER
RX Data
DECODER
COMPARATOR
TRANSMITTER SECTION
DRIVER
TX Data Out
SHAPING
NETWORK
DRIVER
TX Data Out
SHAPING
NETWORK
TX Data In
TX Data In
ENCODER
TX INHIBIT
FIGURE 1. BUS-63100 BLOCK DIAGRAM
M
DDC Custom Monolithics utilized in this product are copyright under the Semiconductor chip Protection Act.
DIY cheap CPLD learning board
This is a CPLD learning board I DIYThe purpose of DIY is to learn and understand the development process of CPLD, so the function is relatively simple, with only a few LEDs, hahaSince it is all handma...
chenzhufly DIY/Open Source Hardware
About the AD sampling fluctuation of DSP
When the voltage waveform at the AD port of DSP is a pure sine wave (as shown in the red waveform), the AD sampling result will have non-periodic bad pixels (as shown in the blue waveform). The figure...
zk_123 DSP and ARM Processors
I hope you can recommend some suitable voltage stabilizers.
It is required to be powered by a 3.6V battery, which needs to be converted to 3.3V (more than 400mA) and 1.8V (100mA is enough). In order to squeeze out as much power as possible, I hope it can still...
wide Embedded System
Voltage reference and time reference
Voltage Reference and Time Reference All analog-to-digital converters (ADCs) and digital-to-analog converters (DACs) require a reference signal, usually a voltage reference. The digital output of an A...
fighting Test/Measurement
If you are familiar with the suspend->resume process, please enter
System suspend: BatteryGetStatus!temp_vol 374 WAIT_OBJECT_0 BatteryGetStatus!temp_vol 375 :: BACKLIGHT OFF ! [A_HW] IOControl(IOCTL_POWER_SET) : D0 => D4 [A_HW] IOControl : System Power State - suspen...
shangyl Embedded System
Your name is so charming that it’s hard to control!
[color=#333333][font=Arial,]Your name is so coquettish that it is hard to control! [/font][/color] [color=#333333][font=Arial,] [/font][/color]...
qwqwqw2088 Talking

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2555  1009  2289  234  2073  52  21  47  5  42 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号