REVISION AG
DO NOT
SCALE FROM
THIS PRINT
NOTES:
1.
REPRESENTS A CRITICAL DIMENSION.
2. MINIMUM PUSHOUT FORCE: 16 OZ FOR TERMINALS, 12 OZ FOR WELD TABS,
AND 8 OZ FOR LOCKING CLIPS.
3. MEASURED FROM BEND.
4. MAXIMUM TERMINAL BURR: .003 [.08].
5. MAXIMUM HEIGHT VARIATION BETWEEN ANY TWO PINS: .005 [.13].
6. DUE TO THE HIGH AMOUNT OF INSERTION FORCE NEEDED, THE -LC OPTION
IS NOT COMPATIBLE WITH AUTO PLACEMENT. SAMTEC RECOMMENDS
MANUAL PLACEMENT FOR ALL ASSEMBLIES WITH THE -LC OPTION.
TFM-1XX-XX-X-S-XX
No OF POSITIONS
ALL POSITIONS AVAILABLE
-02 THRU -50
OPTION
-A: ALIGNMENT PIN (USE TFM-XX-S-01-A)
(NOT AVAILABLE WITH -WT OPTION)
(SEE FIG 5, SHEET 2)
-LC: LOCKING CLIP (USE LC-05-TM)
(NOT AVAILABLE WITH -WT OPTION)
(SEE FIG 7, SHEET 3) (SEE NOTE 6)
-P: PICK AND PLACE PAD (USE PPP-15)
(SEE FIG 6, SHEET 2)
(ONLY AVAILABLE ON -08 THRU -50 POSITIONS)
-K: POLYIMIDE FILM (SEE FIG 3, SHEET 2)
(USE K-DOT-.217-.313-.005)
-WT: WELD TABS (USE WT-25-07-T)
(SEE FIG 4, SHEET 2)
(AVAILABLE ON -02 THRU -30 POS ONLY)
(NOT AVAILABLE WITH -A OR -LC OPTIONS)
-TR: TAPE & REEL
(SEE SHEET 3, TAPE AND REEL VIEW)
-SN: SOLDER NAIL (USE WT-27-03)
**
(NOT AVAILABLE WITH -A, -LC, OR
-WT OPTIONS) (SEE FIG 8, SHEET 3)
BODY SPECIFICATION
-S: SINGLE ROW
(USE TFM-XX-S-XX-XX)
((No. OF POSITIONS x .050[1.27])
+ .125[3.18])REF
((No. OF POSITIONS x .050[1.27])
+ .025[.64])REF
.100 2.54 REF
.065 1.65
01
.050 1.27 REF
.175 4.45 REF
.105 2.67 REF
LEAD STYLE
-01: T-1R16-01-X-2
THROUGH HOLE
-02: T-1R16-01-X-2
SURFACE MOUNT
-03: T-1R16-10-X
THROUGH HOLE
PLATING SPECIFICATIONS
-S: 30µ" SELECTIVE GOLD IN CONTACT AREA,
MATTE TIN ON TAIL
-F: 3µ" FLASH GOLD IN CONTACT AREA,
MATTE TIN ON TAIL
-G: 30µ" GOLD IN CONTACT AREA,
3µ" GOLD ON TAIL
-L: 15µ" LIGHT GOLD IN CONTACT AREA,
MATTE TIN ON TAIL
-H: 50µ" HEAVY GOLD IN CONTACT AREA,
3µ" GOLD ON TAIL
-T: MATTE TIN CONTACT AND TAIL
.083 2.11
**
NOT TOOLED
((No. OF POSITIONS x .050[1.27])
- .050[1.27])
2 MAX SWAY
(EITHER DIRECTION)
"A"
.018 0.46 REF
2 MAX SWAY
(EITHER DIRECTION)
"B" REF
.2200 5.588
REF
.1635 4.153 REF
"A"
.014 0.36 REF
((No. OF POSITIONS x .050[1.27])
- .050[1.27])
"A" .003
2 MAX SWAY
(EITHER DIRECTION)
.010 0.25 REF
2 MAX SWAY
(EITHER DIRECTION)
"C"±.003
TABLE 1
COPLANARITY
POSITION
-02 THRU -29
.004 [.10]
-030 THRU -39
.006 [.15]
-40 THRU -50
.008 [.20]
SECTION "A"-"A"
IN-PROCESS
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS
(TFM-115-01-X-S-XX SHOWN)
FIG 1
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
LEAD STYLE
-01
-02
-03
TABLE 2
BODY
"A"
"B"
"C"
"E"
TFM-XX-S-01-XX .078 [1.98] .131 [3.33] .428 [10.87] .303 [7.70]
TFM-XX-S-01-XX
N/A
.131 [3.33] .428 [10.87] .231 [5.87]
TFM-XX-S-01-XX .111 [3.33] .139 [3.53] .645 [16.38] .356 [9.04]
.XX: .01 [.3]
2
.XXX: .005 [.13]
.XXXX: .0020 [.051]
ANGLES
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail info@SAMTEC.com
code 55322
DESCRIPTION:
DWG. NO.
MATERIAL:
INSULATOR: LCP, UL 94 V0, COLOR: BLACK
TERMINAL: PHOSPHOR BRONZE
DO NOT SCALE DRAWING
SHEET SCALE: 1:0.4
.050 C.L. SINGLE ROW SHROUDED TERMINAL STRIP
TFM-1XX-XX-X-S-XX
8/21/2008
SHEET
1
OF
3
F:\DWG\MISC\MKTG\TFM-1XX-XX-X-S-XX-MKT.SLDDRW
BY:
D. SCHMELZ
REVISION AG
"B"
2 MAX SWAY
(EITHER DIRECTION)
NOTE: “R” = OVERALL LENGTH REF
“S” = ((“R” - .216[5.49]) /2) ±.020[.51]
.021±.010 0.52±0.254
.216 5.49
90°
.226±.006 5.74±0.152
"B"
2 MAX SWAY
(EITHER DIRECTION)
02
0
SEE TABLE 1, SHT 1
"S"
7
"R"
"E"
(SEE TABLE 2,
SHT 1)
FLUSH TO .012 0.30 MAX
(SEE NOTE 3)
.185 4.70 MAX
03
01
SECTION "B"-"B"
((No. OF POSITIONS x .050[1.27]) -.050[1.27])
(TOL ACCUM ±.005[.13] OVER 50 POS.)
SURFACE MOUNT
(TFM-115-02-X-S-XX SHOWN)
(DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1)
"E"
(SEE TABLE 2,
SHT 1)
FIG 2
-K: POLYIMIDE FILM PAD
(TFM-115-02-X-S-K SHOWN)
NOTE: “M” = (No. OF POSITIONS X .050[1.27]) + .125[3.18] REF
WITH -WT “M” = (No. OF POSITIONS X .050[1.27]) + .263[6.68] REF
“P” = ((“M” - .375[9.53]) /2) ±.020[.51]
FIG 3
((NO OF POSITIONS X .050[1.27])
+.263[6.68]) REF
"D"
TFM-XX-S-01-WT
WT-25-07-T
"M"
"P"
.093 2.36 (TYP)
.010 0.25
REF (TYP)
2 MAX SWAY
(EITHER DIRECTION)
((No. OF POSITIONS x .050[1.27])
+ .154[3.91])
"D"
.025 0.64
REF
.375 9.53
REF
"E"
.175 4.45
REF
PPP-15
SECTION "D"-"D"
.050 1.27
-WT OPTION
(TFM-114-01-X-S-WT SHOWN)
(DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1)
FIG 4
C
L
"E"
-P OPTION
(TFM-115-02-X-S-P SHOWN)
(DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1)
(PAD TO BE POSITIONED ON CL AS SHOWN)
FIG 6
SECTION "E"-"E"
.045 1.14 REF
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
.050 1.27
REF
((No. OF POSITIONS x .050[1.27])
+ .075[1.91])
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail info@SAMTEC.com
code 55322
DESCRIPTION:
DWG. NO.
-A OPTION
(TFM-115-02-X-S-A SHOWN)
(DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1)
FIG 5
R.025 0.64
DO NOT SCALE DRAWING
SHEET SCALE: 2:1
.050 C.L. SINGLE ROW SHROUDED TERMINAL STRIP
TFM-1XX-XX-X-S-XX
8/21/2008
SHEET
2
OF
3
BY:
D. SCHMELZ
F:\DWG\MISC\MKTG\TFM-1XX-XX-X-S-XX-MKT.SLDDRW
REVISION AG
PT-1-24-11-09
ROUND HOLES
POSITION 01
(No OF POSITIONS x .050[1.27]) + .275 REF
"G"
FLUSH TO .005 0.13
ABOVE
OBLONG HOLES
.054 1.37
REF
USER DIRECTION OF UN-REELING
POCKET NOT DETAILED
"G"
(No. OF POSITIONS x .050[1.27])
+.175[4.45]
2 MAX SWAY
(EITHER DIRECTION)
WT-27-03-X
.075 1.91
REF
.026 0.66 REF
(2 PLCS)
PACKAGING TUBE VIEW
NOTES:
1. USE PT-1-24-11-09 TUBE
AND (2) TP-24 FOR -A, -LC, WT,
AND -SN OPTIONS.
2. USE PT-1-24-03-09 TUBE AND
(2) TP-09 FOR -P AND -K OPTIONS.
3. LOAD TUBE WITH 1ST POSITION
IN SAME DIRECTION AS ARROW
SECTION "G"-"G"
SCALE 3 : 1
TAPE AND REEL VIEW
**
-SN OPTION
(TFM-110-02-X-S-SN SHOWN)
(DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1)
**
NOT TOOLED
FIG 8
TFM-1XX-02-S-LC
C
L
C
.050 1.27
LC-05-TM
.056 1.42 REF
*
*
*
.010 0.25 REF
2 MAX SWAY
(EITHER DIRECTION)
((No. OF POSITIONS x .050[1.27])
+ .075[1.91])±.002[.05]
2 MAX SWAY
(EITHER DIRECTION)
* INSPECT ONLY WHEN APPLICABLE WITH RESPECT TO ASSEMBLY OPTION
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
-LC OPTION
(TFM-115-01-X-S-LC SHOWN)
(DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 2)
FIG 7
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail info@SAMTEC.com
code 55322
DESCRIPTION:
DO NOT SCALE DRAWING
SHEET SCALE: 2:1
.050 C.L. SINGLE ROW SHROUDED TERMINAL STRIP
DWG. NO.
TFM-1XX-XX-X-S-XX
8/21/2008
SHEET
3
OF
3
F:\DWG\MISC\MKTG\TFM-1XX-XX-X-S-XX-MKT.SLDDRW
BY:
D. SCHMELZ
DSP and ARM Processors
京公网安备 11010802033920号
EEWORLD
