EEWORLDEEWORLDEEWORLD

Part Number

Search

PB06S-60-1ESNT

Description
6A, 115/250VAC, MALE, MAINS POWER CONNECTOR, SOLDER, SOCKET
CategoryThe connector    The connector   
File Size272KB,3 Pages
ManufacturerPower Dynamics, Inc.
Websitehttp://www.powerdynamics.com/
Environmental Compliance  
Download Datasheet Parametric View All

PB06S-60-1ESNT Overview

6A, 115/250VAC, MALE, MAINS POWER CONNECTOR, SOLDER, SOCKET

PB06S-60-1ESNT Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerPower Dynamics, Inc.
Reach Compliance Codecompliant
Other featuresSTANDARDS: IEC 60320; UL; CSA; VDE
Body/casing typeSOCKET
Connector typeMAINS POWER CONNECTOR
Contact to complete cooperationNOT SPECIFIED
Contact completed and terminatedNOT SPECIFIED
Contact point genderMALE
Contact materialNOT SPECIFIED
Coupling typeSNAP
DIN complianceNO
IEC complianceYES
MIL complianceNO
Power Connector Ratings6A, 115/250VAC
Manufacturer's serial numberPB
Installation typePANEL
OptionsGENERAL PURPOSE
Termination typeSOLDER
Total number of contacts3
POWER LINE FILTER
PB Series
STRAIGHT, SNAP-IN/FLANGE MOUNT FILTER WITH IEC 60320
AC INLET SOCKET.
MECHANICAL DIMENSIONS
(Unit: mm)
50.1
30.3
22.5
40.0
28.5
4-R5
21.6
2-
3.3
40.0
3.5
SUGGESTED PANEL CUTOUT
(MOUNTING FROM FRONT)
45.9
47.4
41.8
54.0
FEATURES
The PB series, similar to PA and PASP series, offers filters with
IEC connector providing effective equipment protection of
line-to-ground noise up to 15 Amp, 250VAC. The compact
design filter with low leakage current is well suited for
applications that require strict national and international
emission standards. These filters are also available for
Medical application and offer extremely low Leakage current
to comply with UL544, UL2601 and CSA22.2 standards.
A ground choke can be added to enhance the grounding
ability of the circuit. Bleeder resistor can also be added to
prevent excessive voltages from developing across the filter
capacitors when there is no load.
G
28.3
20.6
31.0
24.0
21.9
4-R2
APPLICATIONS
Computer & networking equipment, Measuring & control
equipment, Data processing equipment, laboratory instruments,
Switching power supplies, other electronic equipment.
28.5
SUGGESTED PANEL CUTOUT
(MOUNTING FROM FRONT)
THICKNESS OF PANEL IS FROM
1.00mm to 1.6mm
TECHNICAL DATA
Rated Voltage: 115/250VAC
Rated Current: 1A, 2A, 3A, 6A, 10A, 15A
Power Line Frequency: 50/60Hz
Max. Leakage Current each
Line to Ground:
@ 115VAC 60Hz: 0.25mA
@ 250VAC 50Hz: 0.45mA
@ 115VAC 60Hz: 2
µ
A*
@ 250VAC 50Hz: 5
µ
A*
Hipot Rating (one minute)
Line to Ground: 2250VDC
Line to Line: 1450VDC
Temperature Range: -25C to +85C
* Medical application
3.6
51.8
40.9
28.3
20.6
Specifications subject to change without notice. Dimensions (mm). See Appendix A for
recommended power cord. See PDI full line catalog for detailed specifications on power cords.
145 Algonquin Parkway, Whippany, NJ 07981 • 973-560-0019 • FAX: 973-560-0076
e-mail: filtersales@powerdynamics.com •
www.powerdynamics.com
7
After tShell is redirected to pty, it is always PEND (details inside)
Direct the shell to two ptys, data write--> pty1 --> shell read data read <-- pty2 <--shell write. Using two unidirectional ptys is based on the pty description of VxWorks. The following phenomena occ...
789137 Embedded System
ARM assembly learning 1
It is very cumbersome to write a program completely in assembly language. Therefore, usually, only a small amount of work that must be done by the assembly program is used, and the rest of the work is...
huang301 Linux and Android
Show the process of WEBENCH design + multi-channel crystal oscillator design
Sometimes you need more than one crystal oscillator. In this case, you can use TI WEBENCH to simply click on the crystal oscillator menu and enter the parameters:Click to start design:Click to generat...
ddllxxrr Analogue and Mixed Signal
Serial transmission errors occur when the baud rate is high
When sending and receiving data via the serial port, as long as the baud rate is increased, the data transmission will go wrong, especially on the receiving side. I don't know what the reason is. The ...
flyactel Embedded System
"The remote connection to the device has been lost. Please verify the device connection and restart debugging"???
When I pull a data table from the computer on the PDA, and then when the PDA stores data on itself, it says "Remote connection to the device has been lost. Please verify the device connection and rest...
niuhuang123 Embedded System
EE_FPGA Hardware Manual V1.0
Partial page previewDownload Link:...
chenzhufly FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2067  1214  2803  1020  1107  42  25  57  21  23 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号