BR26-37B2-6V datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Mechanical and electronic products> relay> BR26-37B2-6V

BR26-37B2-6V: DescriptionPower/Signal Relay, 2 Form C, DPDT, Momentary, 0.162A (Coil), 6VDC (Coil), 972mW (Coil), 2A (Contact), 28VDC (Contact), DC Input, Random, AC/DC Output, Panel Mount,; CategoryMechanical and electronic products relay; File Size120KB，2 Pages; ManufacturerMicrosemi; Websitehttps://www.microsemi.com

Download Datasheet Parametric View All

BR26-37B2-6V Overview

Power/Signal Relay, 2 Form C, DPDT, Momentary, 0.162A (Coil), 6VDC (Coil), 972mW (Coil), 2A (Contact), 28VDC (Contact), DC Input, Random, AC/DC Output, Panel Mount,

BR26-37B2-6V Parametric

Parameter Name	Attribute value
Maker	Microsemi
Reach Compliance Code	compliant
ECCN code	EAR99
body width	10.16 mm
body height	10.41 mm
Body length or diameter	20.57 mm
Maximum coil current (DC)	0.162 A
Coil operating voltage (DC)	4.4 V
Coil power	972 mW
Coil release voltage (DC)	0.3 V
Coil resistance	37 Ω
Maximum coil voltage (DC)	6 V
Nominal coil voltage	6 V
Coil/Input Power Type	DC
Contact (AC) maximum rated R load	2A@115VAC
Maximum contact current (AC)	2 A
Maximum contact current (DC)	2 A
Contact (DC) maximum rated R load	2A@28VDC
Contact resistance	50 mΩ
Maximum contact voltage (AC)	115 V
Maximum contact voltage (DC)	28 V
Contact/Output Power Type	AC/DC
Dielectric strength between coil and contacts	1000 Vrms
Dielectric strength between breaking contacts	500 Vrms
Electrical life	100000 Cycle(s)
Input switching control type	Random
Insulation resistance	10000000000 Ω
Installation features	PANEL MOUNT
Number of terminals	8
operating hours	6 ms
Maximum operating temperature	125 °C
Minimum operating temperature	-65 °C
physical size	20.57mm x 10.16mm x 10.41mm
Guideline	MIL-PRF-39016
Relay action	MOMENTARY
Relay style	2 FORM C
Relay function	DPDT
Relay type	POWER/SIGNAL RELAY
release time	6 ms
surface mount	NO
Termination type	SOLDER HOOK
weight	7 g

Preview

Download Datasheet

View All

BR26

Half-Size Crystal Can

Welded • DPDT

Dry Circuit to 2 Amps

SPECIFICATIONS

GENERAL

Contact Arrangement

.......................... 2PDT (2 Form C)

Weight........................................................0.25

oz approx.

Designed to meet the requirements of MIL-PRF-39016.

ENVIRONMENTAL

Temperature Range

............................... -65 C to +125 C

Vibration

(Note 2)................................ 0.4" DA 10 - 38 Hz

20 G's 38 - 2,000 Hz

Shock (Operating)(Note

2) ........................ 50 G's 11 ms

PERFORMANCE

Contact Rating

(Note 1):

Resistive .............. 2 Amps @ 28 VDC or 115V 400 Hz

(Case Ungrounded)

Low Level ............................ 10-50 µA @ 10-50 mv DC

or peak AC (Note 4)

Life

...................................100,000 operations minimum

@ rated load, 125 C

Pull In Power

............................................250 mw approx.

Operate/Release Time

.................... 4 ms max, excluding

bounce time at nominal coil voltage

Contact Bounce Time.....................2

ms max @ 2 Amps

28 VDC

Contact Resistance:

Before Life....................... 0.050 Ohms max @ 2 Amps

and 6 VDC

After Life .......................... 0.100 Ohms max @ 2 Amps

and 6 VDC

ELECTRICAL CHARACTERISTICS

Duty Cycle........................................................Continuous

Insulation Resistance

10,000 megohms @ 500V 25 C

1,000 megohms @ 500V 125 C

Dielectric Strength:

Sea Level:

Contact to Case ................................... 1,000 VRMS

Contact to Coil ..................................... 1,000 VRMS

Coil to Case ............................................ 500 VRMS

Across Open Contacts ........................... 500 VRMS

70,000 Feet:

All Points ................................................. 350 VRMS

Notes:

For case grounded loads and other ratings, consult the

factory.

For applications requiring other shock and vibration

levels, consult the factory.

For other ratings consult the factory.

Relay contacts which have switched high level currents

are no longer suitable for switching low level loads.

14930 E. Alondra Blvd., La Mirada, CA 90638-5752 (714) 994-6500 FAX (714) 994-3013

W:2000, Rev. 2

Recommended Resources

Those classic analog circuits worth collecting

The three-phase four-wire active energy meter is connected to the circuit through the current transformer (2)

One of the dual-tone electronic doorbell circuits

A5348 smoke alarm detection circuit - typical application

Power frequency 50HZ square wave circuit

810 computer motherboard circuit diagram_17

Microcontroller power supply problem: The microcontroller is powered by 5V, and the voltage ripple from the 7805 input and output after filtering is about 50mVpp. Electrolytic capacitors and 104 capacitors are added for filtering before t...; 子乐 MCU

KIA 50N03 output current: I would like to ask if anyone has used this NMOS tube, if the GS input voltage is 3.3V, what is the DS output current? The datasheet does not specify...; tangwei8802429 Analog electronics

Several new uses for mobile phones: We may know some self-help methods in emergency situations, but you may not know that your mobile phone can also save your life in a critical moment. Check out the following content to learn what your...; 呱呱 Mobile and portable

Optimization of DSP Hardware Implementation (VII)—Fixed-Point Representation in Hardware Implementation: Implementing DSP with hardware is basically based on fixed-point algorithms. What is fixed-point? Fixed-point means that the position of the decimal point is fixed, which is different from floating-po...; fish001 DSP and ARM Processors

KEYSIGHT Column solution is here, please read more posts: [font=微软雅黑][size=4][font=Verdana][size=2][size=10.5pt][color=RoyalBlue][b][font=微软雅黑][size=5]Challenges and Solutions for Testing Consumer Electronics IoT Devices[/size][/font][/b][/color] [/size][/si...; EEWORLD社区 Integrated technical exchanges

warning: creating output section .vectors without SECTIONS specification: [i=s] This post was last edited by dontium on 2015-1-23 11:33 [/i] My chip is C6414. When I build, there is always a warning saying that .vectors has no specified segment? In the map file, I can see t...; eeszg DSP and ARM Processors

Shortcut: 00 01 02 03 04 05 06 07 08 09 0A 0C 0F 0J 0L 0M 0R 0S 0T 0Z 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 1H 1K 1M 1N 1P 1S 1T 1V 1X 1Z 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 2G 2K 2M 2N 2P 2Q 2R 2S 2T 2W 2Z 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 3G 3H 3J 3K 3L 3M 3N 3P 3R 3S 3T 3V 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4M 4N 4P 4S 4T 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5E 5G 5H 5K 5M 5N 5P 5S 5T 5V 60 61 62 63 64 65 66 67 68 69 6A 6C 6E 6F 6M 6N 6P 6R 6S 6T 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7M 7N 7P 7Q 7V 7W 7X 80 81 82 83 84 85 86 87 88 89 8A 8D 8E 8L 8N 8P 8S 8T 8W 8Y 8Z 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9F 9G 9H 9L 9S 9T 9W

Popular Components