1206SFS600F datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > 1206SFS600F

Preview

1206SFS600F: DescriptionSurface-mount Fuses Fundamentals; File Size1MB，28 Pages; ManufacturerMACOM; Websitehttp://www.macom.com

Download Datasheet View All

1206SFS600F Overview

Surface-mount Fuses Fundamentals

Preview

Download Datasheet

View All

Surface-mount Fuses

– Fundamentals

Surface-mount Fuses

Fundamentals

Overview

TE Circuit Protection offers the widest selection of surface-mount

fuses available for addressing a broad range of overcurrent

protection applications. Helping to prevent costly damage and

promote a safe environment for electronic and electrical

equipment, our single-use chip fuses provide performance stability

to support applications with current ratings from .5A up to 20A.

TE Circuit Protection also offers the telecom FT600 fuse for

telecommunications applications. This telecom fuse helps comply

with North American overcurrent protection requirements,

including Telcordia, GR-1089, TIA-968-A (formerly FCC Part 68),

and UL60950 3rd edition.

Multi-layer Design for Chip Fuses

The multi-layer design has the benefit of exposing more fuse

element surface area to the glass-ceramic absorption material.

When the fuse elements open, there is more material for the

vaporizing fuse metals to absorb into, resulting in a very efficient

and effective quenching of the fuse arc.

Figure 1 compared the multi-layer design of our SFF fuses with

standard glass coated designs. The glass coated designs rely on

the coating on only one side of the fuse element to absorb the

vaporizing fuse material when it opens. Therefore, there is much

less absorption material available to absorb the fuse metals. The

result can be prolonged arcing and possible coating breach.

Figure 2 shows how the absorption characteristics of the two

designs differ. The multi-layer design indicates a clean separation

with the fuse element evenly diffusing into the surrounding

ceramic substrate. In the glass coated design, the element

diffusion takes place in a small portion of the device and is only

absorbed by the glass material directly above the area of failure.

Figure 1

Glass/Ceramic

Substrate

Multiple Fuse

Elements

Substrate

Material

Single Fuse Glass

Element Coating

Multi-layer Design

Single-layer Glass Coated Design

Figure 2

Fault Zones

Multi-layer Design

Single-layer Glass Coated Design

Wire-In-Air Design for 2410SFV Fuses

The 2410(6125) is a Wire-In-Air SMD Fuse which is very suitable

for secondary level over current protection applications.

Figure 3 compared our straight wire element design 2410SFV

fuses with normal corrugating wire design fuse. The straight wire

element in air performs consistent fusing and cutting

characteristics together with excellent inrush current

withstanding capability.

Introduced PCB assembly technology into 2410SFV fuses design

and manufacture, we achieved on lead free completely and no

end cap falling off risk comparing with traditional ceramic body

with end cap fuse.

Figure 3

Glass fiber enforced

epoxy body

Straight wire element

Copper terminal

plated with Ni and Tin

Ceramic body

Corrugate wire element

End cap plated with Tin

Recommended Resources

External voltage control output voltage circuit diagram

Constant current charging circuit

Electronic acupoint physiotherapy device circuit

Single board computer automatic reset and start circuit

Double fluorescent lamp wiring method

Cleverly measure small-capacity capacitors using composite tubes

DSP Program Structure Programming Notes: If the program can be written to adapt to the structure of the DSP to a certain extent, the optimization function of the C compiler can greatly improve the performance of the algorithm on the basis of...; Aguilera DSP and ARM Processors

splce20: vs2005 wm5.0 installed sqlce20.ppc.wce5.armv4i.cab and sqlce20.dev.ppc.wce5.armv4i.cab in the simulator. When viewing the **.sdf file, the following error pops up: Error: 0x80004005 E_FAIL Nativ Error...; laker28 Embedded System

400 Examples of Practical New Electronic Design PDF: ...; Jackwin Integrated technical exchanges

[MSP430 compiler usage experience] Using CCS again - follow-up: [i=s]This post was last edited by xiaofeng916636 on 2014-8-17 23:19[/i] Since the previous post was posted a long time ago, it cannot be edited again. I haven't used CCS for a long time. The last time...; 啸风916636 Microcontroller MCU

IIR filter zero-phase digital filtering and its application: IIR filter zero-phase digital filtering and its applicationAuthor's name: Fan Xinhai, An Gang, Zhang Chuanqing Journal: Foreign Electronic Measurement Technology Issue: 2005 Issue 8Abstract: This pape...; fighting Analog electronics

How to calculate the voltage spike generated by the primary leakage inductance Lp?: [color=#000][font=Tahoma, Helvetica, sans-serif]How to calculate the voltage spike generated by the primary leakage inductance Lp? Some information says = leakage inductance Lp divided by Coss and the...; xiefei Power technology

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components