UPD78355GD(A)-5BB datasheet, PDF

Datasheet> All Categories > The embedded processor and controller> Microcontrollers and processors> UPD78355GD(A)-5BB

UPD78355GD(A)-5BB: Description16-BIT, 32MHz, MICROCONTROLLER, PQFP120, 28 X 28 MM, PLASTIC, QFP-120; CategoryThe embedded processor and controller Microcontrollers and processors; File Size2MB，519 Pages; ManufacturerRenesas Electronics Corporation; Websitehttps://www.renesas.com/

Download Datasheet Parametric View All

UPD78355GD(A)-5BB Overview

16-BIT, 32MHz, MICROCONTROLLER, PQFP120, 28 X 28 MM, PLASTIC, QFP-120

UPD78355GD(A)-5BB Parametric

Parameter Name	Attribute value
Maker	Renesas Electronics Corporation
Parts packaging code	QFP
package instruction	QFP,
Contacts	120
Reach Compliance Code	unknown
Has ADC	YES
Address bus width	16
bit size	16
maximum clock frequency	16 MHz
DAC channel	YES
DMA channel	NO
External data bus width	8
JESD-30 code	S-PQFP-G120
Number of I/O lines	48
Number of terminals	120
PWM channel	YES
Package body material	PLASTIC/EPOXY
encapsulated code	QFP
Package shape	SQUARE
Package form	FLATPACK
Certification status	Not Qualified
speed	32 MHz
surface mount	YES
technology	CMOS
Terminal form	GULL WING
Terminal location	QUAD
uPs/uCs/peripheral integrated circuit type	MICROCONTROLLER

Preview

Download Datasheet

View All

PD78356

16-BIT SINGLE-CHIP MICROCONTROLLER

HARDWARE

PD78355

PD78356

PD78P356

1993

Document No. U10669EJ3V0UM00 (3rd edition)

(Previous No. IEU-1361)

Date Published February 1996 P

Printed in Japan

NOTES FOR CMOS DEVICES

PRECAUTION AGAINST ESD FOR SEMICONDUCTORS

Note:

Strong electric field, when exposed to a MOS device, can cause destruction of the gate oxide and

ultimately degrade the device operation. Steps must be taken to stop generation of static electricity

as much as possible, and quickly dissipate it once, when it has occurred. Environmental control

must be adequate. When it is dry, humidifier should be used. It is recommended to avoid using

insulators that easily build static electricity. Semiconductor devices must be stored and transported

in an anti-static container, static shielding bag or conductive material. All test and measurement

tools including work bench and floor should be grounded. The operator should be grounded using

wrist strap. Semiconductor devices must not be touched with bare hands. Similar precautions need

to be taken for PW boards with semiconductor devices on it.

HANDLING OF UNUSED INPUT PINS FOR CMOS

Note:

No connection for CMOS device inputs can be cause of malfunction. If no connection is provided

to the input pins, it is possible that an internal input level may be generated due to noise, etc., hence

causing malfunction. CMOS devices behave differently than Bipolar or NMOS devices. Input levels

of CMOS devices must be fixed high or low by using a pull-up or pull-down circuitry. Each unused

pin should be connected to V

or GND with a resistor, if it is considered to have a possibility of

being an output pin. All handling related to the unused pins must be judged device by device and

related specifications governing the devices.

STATUS BEFORE INITIALIZATION OF MOS DEVICES

Note:

Power-on does not necessarily define initial status of MOS device. Production process of MOS

does not define the initial operation status of the device. Immediately after the power source is

turned ON, the devices with reset function have not yet been initialized. Hence, power-on does

not guarantee out-pin levels, I/O settings or contents of registers. Device is not initialized until the

reset signal is received. Reset operation must be executed immediately after power-on for devices

having reset function.

QTOP is a trademark of NEC Corporation.

MS-DOS and Windows are trademarks of Microsoft Corporation.

PC/AT and PC DOS are trademarks of IBM Corporation.

SPARCstation is a trademark of SPARC International, Inc.

SunOS is a trademark of Sun-Microsystems, Inc.

HP9000 Series 700 and HP-UX are trademarks of Hewlett-Packard Company.

NEWS and NEWS-OS are trademarks of SONY Corporation.

TRON is an abbreviation of The Real-time Operating System Nucleus.

ITRON is an abbreviation of Industrial TRON.

The export of these products from Japan is regulated by the Japanese government. The export of some or all of these

products may be prohibited without governmental license. To export or re-export some or all of these products from a

country other than Japan may also be prohibited without a license from that country. Please call an NEC sales

representative.

License not needed

PD78355/(A)/(A1)/(A2), 78P356KP-S

The customer must judge the need for license

PD78356/(A)/(A1)/(A2), 78P356GC-7EA,

78P356GD-5BB/(A)/(A1)/(A2)

The information in this document is subject to change without notice.

No part of this document may be copied or reproduced in any form or by any means without the prior written

consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in

this document.

NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property

rights of third parties by or arising from use of a device described herein or any other liability arising from use

of such device. No license, either express, implied or otherwise, is granted under any patents, copyrights or other

intellectual property rights of NEC Corporation or others.

While NEC Corporation has been making continuous effort to enhance the reliability of its semiconductor devices,

the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury to persons or

property arising from a defect in an NEC semiconductor device, customer must incorporate sufficient safety

measures in its design, such as redundancy, fire-containment, and anti-failure features.

NEC devices are classified into the following three quality grades:

“Standard”, “Special”, and “Specific”. The Specific quality grade applies only to devices developed based on a

customer designated “quality assurance program” for a specific application. The recommended applications of

a device depend on its quality grade, as indicated below. Customers must check the quality grade of each device

before using it in a particular application.

Standard: Computers, office equipment, communications equipment, test and measurement equipment, audio

and visual equipment, home electronic appliances, machine tools, personal electronic equipment

and industrial robots

Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster

systems, anti-crime systems, safety equipment and medical equipment (not specifically designed

for life support)

Specific: Aircrafts, aerospace equipment, submersible repeaters, nuclear reactor control systems, life

support systems or medical equipment for life support, etc.

The quality grade of NEC devices in “Standard” unless otherwise specified in NEC’s Data Sheets or Data Books.

If customers intend to use NEC devices for applications other than those specified for Standard quality grade,

they should contact NEC Sales Representative in advance.

Anti-radioactive design is not implemented in this product.

M7 94.11

Recommended Resources

TDA7264 power amplifier circuit diagram

High stability 25kHz switching power supply circuit

temperature controller circuit

Temperature Controller

DT8 type 40-80A direct access electric meter wiring

Flash beat circuit once per second

Smart wax therapy machine based on STM32 and Gizwits: Smart wax therapy machine based on STM32 and GizwitsAbstract: With the recognition of the effect of physical therapy in the treatment of chronic diseases, traditional paraffin therapy has been widely ...; 毛球大大 RF/Wirelessly

Is there a future in smart card operating system development? Will it be difficult to switch jobs and do other things, such as ARM development?: As the title says, I am about to start working and feel confused about my future. I need advice from experienced people....; tanglongzhu ARM Technology

Two LM3S9B96 SPI communication problem: [p=18, null, left][color=#000]I can use SSI0 as the master to send data and SSI1 as the slave to receive data on one board. But when I split the program and downloaded the master and slave programs to...; fendou Microcontroller MCU

Segmented paging mechanism: Is segmentation and paging mechanism not needed in embedded systems? Please explain the segmentation and paging mechanism to me, thank you:)...; taodan Embedded System

My touchpad finally arrived: Reverse:There is also a little thing...; ddllxxrr Microcontroller MCU

pcs7: When using PCS7, there is no actual hardware, only a computer. I want to use PLCSIM to simulate a boiler control system. Can I do it? If I can, what is the approximate sequence? For example, to contro...; sanjin Industrial Control Electronics

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components