EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-MLPFA3242

Description
Transponder, 10709Mbps(Tx), 10709Mbps(Rx), FC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerJDS Uniphase Corporation ( VIAVI )
Websitehttp://www.jdsu.com/index.html
Download Datasheet Parametric View All

PH1-MLPFA3242 Overview

Transponder, 10709Mbps(Tx), 10709Mbps(Rx), FC/UPC Connector,

PH1-MLPFA3242 Parametric

Parameter NameAttribute value
MakerJDS Uniphase Corporation ( VIAVI )
Reach Compliance Codeunknown
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body width56.1 mm
body height13.2 mm
Body length or diameter76.5 mm
Connection TypeFC/UPC CONNECTOR
Data rate (receive)10709 Mbps
Data rate (send)10709 Mbps
Emitter/Detector TypePIN PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1541 nm
Nominal optical power output1.584 mW
minimum return loss-27 dB
Sensitivity-17 dBm
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
Can anyone help explain the FPGA upload issue?
Why can I upload the whole file sometimes but only partially sometimes? What is the relationship with the hardware? What is the difference between uploading via STI and uploading via external FLASH?...
脚根_梅 FPGA/CPLD
SCSI miniport driver problem
Can anyone explain the basic structure of scsi miniport driver?...
businiao0002007 Embedded System
100 check items for PCB design to ensure you have no problems with your design!
1. Data input stage1. Whether the data received in the process is complete (including: schematic diagram, *.brd file, bill of materials, PCB design instructions and PCB design or change requirements, ...
嘉立创创创 PCB Design
I feel sorry for a certain treasure technology seller
[i=s]This post was last edited by kiroking on 2016-5-29 16:34[/i] First, I feel sorry for the seller on Taobao for 10 seconds. 1. . . 2. . . Forget it, I don't feel bad about it{:1_100:} The cause of ...
kiroking Talking
About the serial port problem in TCC7901_bsp2.2
I am now debugging the TCC7901 chip board in TELECHIPS. TCC7901 has 6 PORTs but only 4 channels. My boss wants me to use all 4 channels in 2.2 BSP. However, 2.2 BSP uses CH0 and CH2 for debugging and ...
hncb9431 Embedded System
Insert node in interrupt service routine
Have you ever tried to insert a node in a linked list in an interrupt service program? You can also set a flag in the interrupt service program. In the main program, the difference flag is used to det...
爱好汽车电子 MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2405  1762  544  1158  1207  49  36  11  24  25 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号