MD-XD-6W
Series
6W, FIXED INPUT ISOLATED & REGULATED TWIN OUTPUT DIP24 DC-DC CONVERTER
6W,
DIP24
PRODUCT PROGRAM
Input
Part
Number
MD120505XD-6W
Nomina
l
12
12
12
12
12
12
24
24
24
24
24
24
48
48
48
48
48
48
Voltage(VDC)
Range
10.8-13.2
10.8-13.2
10.8-13.2
10.8-13.2
10.8-13.2
10.8-13.2
21.6-26.4
21.6-26.4
21.6-26.4
21.6-26.4
21.6-26.4
21.6-26.4
43.2-52.5
43.2-52.5
43.2-52.5
43.2-52.5
43.2-52.5
43.2-52.5
Max*
15
15
15
15
15
15
30
30
30
30
30
30
60
60
60
60
60
60
No-load
Current
(mA,Typ)
25
25
25
25
25
25
15
15
15
15
15
15
10
10
10
10
10
10
Voltage
(VDC)
5/5
7.2/7.2
9/9
12/12
15/15
24/24
5/5
5/12
12/12
15/15
24/05
24/24
5/5
5/12
9/9
12/12
15/15
24/24
Output
Current(MA)
Max
600/600
417/417
333/333
250/250
200/200
125/125
600/600
600/250
250/250
200/200
125/600
125/125
600/600
600/250
333/333
250/250
200/200
125/125
Min.
60/60
42/42
33/33
25/25
20/20
13/13
60/60
60/25
25/25
20/20
13/60
13/13
60/60
60/25
33/33
25/25
20/20
13/13
76
79
78
80
81
82
76
77
80
79
81
81
76
78
78
80
81
82
Efficiency
(%,Typ)
FEATURES
◆
Fixed input voltage range
◆
Twin output
◆
Operating temperature: -40℃ to + 85℃
◆
UL94-V0 package
◆
No external component required
◆
Industry standard pin out
◆
Short circuit protection(
automatic recovery
)
◆
Five-sided metal shielding
◆
MTBF>1,000,000 hours
◆
No heat sink required
◆
RoHS Compliance
MD120707XD-6W
MD120909XD-6W
MD121212XD-6W
MD121515XD-6W
MD122424XD-6W
MD240505XD-6W
MD240512XD-6W
MD241212XD-6W
MD241515XD-6W
MD242405XD-6W
MD242424XD-6W
MD480505XD-6W
MD480512XD-6W
MD480909XD-6W
MD481212XD-6W
MD481515XD-6W
MD482424XD-6W
*Input voltage can't exceed this value, or will cause the permanent damage.
MODEL SELECTION
MD
①
12
②
05
③
05
④
X
⑤
D
⑥
-6W
⑦
①Product
Series
③1st
Output Voltage
⑤Fixed
Input Range
⑦Rated
Power
②Input
Voltage
④2nd
Output Voltage
⑥DIP24Package
Style
APPLICATIONS
The MD_XD-6W series are specially designed for
applications where a wide range input voltage power
supplies are isolated from the input power supply in a
distributed power supply system on a circuit board.
These products apply to:
1)Where the voltage of the input power supply is fixed
voltage range;
2)Where isolation is necessary between input and
output (Isolation Voltage≤1500VDC);
3)Where isolation is necessary between Vout1 and
Vout2 (Isolation Voltage≤1000VDC);
4)Where the regulation of the output voltage and the
output ripple noise are demanded.
COMMON SPECIFICATIONS
Item
Test Conditions
Min.
Typ.
Max.
Units
Storage humidity
Operating temperature
Storage Temperature
Temp. rise at full load
-40
-55
15
1.5mm from case for 10 seconds
Free Air Convection
Plastic (UL94-V0)
Continuous, Automatic Recovery
1000
15
95
85
125
%
℃
PRODUCT ID DESCRIPTION
Lead temperature
Cooling
Case Material
Short circuit protection
MTBF
Weight
300
K hours
g
MICRODC RESERVES THE COPYRIGHT
http://www.microdc.cn
Technical Enquiries-Email:tech@microdc.cn Tel:0086-20-86000646
Page 1 of 3
MD-XD-6W
Series
ISOLATION SPECIFICATIONS
Item
Isolation voltage
Isolation resistance
Isolation capacitance
Test Conditions
Tested for 1 minute and 1mA max
Test at 500VDC
Input/Output, 100KHz/1V
Min.
1500
1000
100
Typ.
Max.
Units
VDC
MΩ
pF
TYPICAL CHARACTERISTICS
*Supply voltage must be discontinued at the end of short circuit duration.
OUTPUT SPECIFICATIONS
Item
Output power
Main output voltage accuracy
Vice-output voltage accuracy
Load regulation
Line regulation
Temperature drift (Vout)
Ripple**
Noise**
Switching frequency
Test Conditions
Refer to product program
Refer to recommended circuit
Refer to recommended circuit
From 10% to 100% load
Input voltage from low to high
Refer to recommended circuit
20MHz Bandwidth
20MHz Bandwidth
100% load, input voltage range
20
75
300
Min.
0.6
±1
±3
±0.5
±0.2
Typ.
Max.
6
±3
±5
±1*
±0.5
±0.03
50
150
%/℃
mVp-p
KHz
%
Units
W
RECOMMENDED CIRCUIT
*Dual output models unbalanced load:
±5%.
**Test ripple and noise by
“parallel
cable”method. See detailed operation instructions at Testing of Power
Converter section, application notes.
APPLICATION NOTE
1) Requirement On Output Load
In order to ensure the product operate efficiently and reliably, in addition to a max load (namely full load), a minimum
load is specified for this kind of DC/DC converter. Make sure the specified range of input voltage is not exceeded, the
minimum output load no less than 10% load.If the actual load is less than the specified minimum load, the output ripple may
increase sharply while its efficiency and reliability will reduce greatly. If the actual output power is very small, please add
appropriate resistor as extra loading, or contact our company for other lower output power products.
2) Recommended Circuit
All the MD-XD-6W Series have been tested according to the following recommended testing circuit before leaving
factory. This series should be tested under load (see Figure 1).
If you want to further decrease the input/output ripple,you can increase capacitance properly or choose capacitors with
low ESR. However, the capacitance should not be too high, or may cause start-up problem. If you want to use the
products
an
in high EMI, please choose our metal packaged products. For every channel of output, provided the safe and reliable
operation is ensured, the greatest capacitance of its filter capacitor sees
(Table 1). General:
Cin:
5V,12V
24V&48V
Cout: 10µF/100mA
100µF
22µF/10µF
EXTERNAL CAPACITOR TABLE (TABLE 1)
3) Input Current
While using unstable power source, please ensure the output voltage and ripple voltage do not exceed indexes of the
converter. The preceding power source must be able to provide for converter sufficient starting current Ip (Figure 2).
General: Ip≤1.4*Iin-max
4) No parallel connection or plug and play
Output External Capacitor Table (Table 1)
Vout(VDC)
Cout(uF)
5
9
12
15
24
680
470
330
220
100
http://www.microdc.cn
Technical Enquiries-Email:tech@microdc.cn Tel:0086-20-86000646
Page 2 of 3
MD-XD-6W
Series
OUTLINE DIMENSIONS
＆
FOOTPRINT DETAILS
MECHANICAL DIMENSIONS
RECOMMENDED FOOTPRINT(TOP VIEW)
TUBE OUTLINE DIMENSIONS
RoHS COMPLIANT INFORMATION
This series is compatible with RoHS soldering systems with a peak wave solder temperature
of 300°C for 10 seconds.
The pin termination finish on the SIP package type is Tin Plate, Hot Dipped over Matte Tin
with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in this
series are backward compatible with Sn/Pb soldering systems.
Microdc Professional Power Module,Inc.
Tel:0086-20-86000646
E-mail:tech@microdc.cn
Website: www.microdc.cn
REACH COMPLIANT INFORMATION
This series has proven that this product does not contain harmful chemicals, it also has
harmful chemical substances through the registration, inspection and approval.
http://www.microdc.cn
Technical Enquiries-Email:tech@microdc.cn Tel:0086-20-86000646
Page 3 of 3
京公网安备 11010802033920号
EEWORLD
