EEWORLDEEWORLDEEWORLD

Part Number

Search

F44TU2705G2000BLK

Description
Fixed Resistor, Metal Glaze/thick Film, 1.3W, 27000000ohm, 14000V, 2% +/-Tol, -2000ppm/Cel
CategoryPassive components    The resistor   
File Size222KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance
Download Datasheet Parametric View All

F44TU2705G2000BLK Overview

Fixed Resistor, Metal Glaze/thick Film, 1.3W, 27000000ohm, 14000V, 2% +/-Tol, -2000ppm/Cel

F44TU2705G2000BLK Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerTT Electronics plc
Reach Compliance Codecompliant
ECCN codeEAR99
structureCylindrical
Number of terminals2
Maximum operating temperature100 °C
Minimum operating temperature-55 °C
Package diameter8.5 mm
Package length55.6 mm
Package shapeCYLINDRICAL PACKAGE
Package formAxial
method of packingBox
Rated power dissipation(P)1.3 W
resistance27000000 Ω
Resistor typeFIXED RESISTOR
technologyMETAL GLAZE/THICK FILM
Temperature Coefficient-2000 ppm/°C
Tolerance2%
Operating Voltage14000 V
High Voltage Thick Film
Resistor
F Series
Termination variants
Wide resistance range
Good resistance stability
Working voltage up to 28KV
Sets available with matched characteristics
Good ratio matching over wide voltage range
Series connection of resistors by screw terminals
½½½½½½½½½½½½½½½½½½
½½½½½½½½½½½½½½½½½½½½½
½½½½½½½½½½
½½½½½½½½½½
½½½½½½½½½½½½½½½½½½½½
Electrical Data
IRC
Type
Power
Rating @
20°C
(watts)
Resistance
Range
(ohms)
Limiting
Element
Voltage
(volts)
In Air
2M to 100G
2M to 150G
4K
14K
In Oil
8K
28K
TCR
(±ppm/°C)
(values>1G:
TCR is 250ppm/°C)
Resistance
Tolerance (%)
(measured at 100
volts dc)
Values
(any value to
special order)
Thermal
Impedance
(°C/watt)
Operating
Temperature
Range (°C)
F43
F44
0.7
1.3
-2000
-2000
2, 5, 10
2, 5, 10
EIA 2%
values
preferred
44
33
-55 to 100
-55 to 100
CONSTRUCTION:
The Cermatox
®
sintered oxide based resistive thick film is fired
onto the surface of a high quality ceramic onto which turned
brass end caps are pressed. A helical cut is made into the film
to adjust its ohmic value and finally a sleeve is fitted to provide
mechanical protection and electrical insulation. Resistors for use
in oil or SF
6
can be supplied with a lacquer protection instead
of the sleeve.
TERMINATIONS:
Three styles of termination are available to permit resistors to
be screwed together in a series chain, with the end members
having axial wires for soldering.
Wire Terminations:
Styles D and KU. See illustration.
Material:
Solder-coated copper wire.
Screw Terminations:
Styles D and KU. See illustration.
Material:
Turned brass.
Screw Thread:
All caps are tapped UNF-10 x 4.2 deep. UNF-
10 is 32 TPI, 60° thread angle 4.72±0.07 mm outside diameter,
3.83 mm core diameter.
Coupling Stud:
All KU & TU resistors are supplied with 8 mm
long screwed brass studs.
MARKING:
Type reference, resistance value, tolerance and data code are
legend marked.
SOLVENT RESISTANCE:
The lacquer and protective sleeve provide excellent resistance
to all normal industrial cleaning solvents suitable for printed
circuits.
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
Wire and Film Technologies Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
F Series Issue October 2008 Sheet 1 of 3
Please tell me how to determine whether a certain bit of a port reads 0
I encountered a problem when doing a DHT11 reading experiment, that is, how to determine whether the IO line reads 0? I used #define IO_READ_H PIND |= (1 If you can judge 1, you can judge 0. Think abo...
whg0109 Microchip MCU
【SensorTag】Why is my SensorTag not responding?
Use TI's BLE Device Monitor program and connect to the computer via the serial port. The interface is as follows:Do I have to use flow control for the RX and TX in the UART I use?...
dontium Wireless Connectivity
Questions about DC
The synthesis includes pads, but whether special constraints are required for the pads; without any processing, the compile_ultra report is as follows: report_timing indicates that the pad capacitance...
eeleader FPGA/CPLD
Regarding the movement of the stepper motor controlled by 8255A, the simulation cannot be done. Please give me some advice. The program is attached.
I am working on a project now, part of which is to use port A of 8255 to control the movement of a stepper motor. The timer 0 interrupt method is adopted, that is, every time an interrupt is entered, ...
zhf120 MCU
Delphi Serial Port
[i=s] This post was last edited by paulhyde on 2014-9-15 09:35 [/i] I practiced writing the serial communication part when programming the host computer. I hope it will be helpful to students who use ...
bluelool1 Electronics Design Contest

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 786  909  400  930  1278  16  19  9  26  39 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号