MN101CD0 Series
Type
Internal ROM type
ROM (byte)
RAM (byte)
Package (Lead-free)
Minimum Instruction
Execution Time
32K
1K
48K
MN101CD0A
MN101CD0C
MN101CD0D
64K
2K
SSOP032-P-0300B
0.10
µs (at
2.7
V to
3.6
V,
10
MHz)
0.125
µs (at
1.8
V to
3.6
V,
8
MHz)
100
µs (at
1.8
V to
3.6
V,
20
kHz)
SSOP032-P-0300B
MN101CD0G
124K
MN101CFD0G
FLASH
128K
Mask ROM
Interrupts
RESET. Watchdog. External
0
to
4.
External
6
(key interrupt dedicated). Timer
0
to
3.
Timer
6.
Timer
7
(2 systems). Time base. Serial
0
(2
systems). A/D conversion finish
Timer Counter
8-bit
timer
×
5
Timer
0
..................Square-wave/8-bit PWM output. Event count. Simple pulse width measurement. Added pulse (2-bit) type PWM
output. Square-wave/PWM output to large current terminal P35 possible
Timer
1
..................Serial
0
baud rate timer
Timer
2
..................Square-wave output. Added pulse (2-bit) type PWM output. PWM output. Event count. Simple pulse width
measurement. Serial
0
baud rate timer. Square-wave/PWM output to large current terminal P34 possible
Timer
3
..................Interval timer
Timer
6
..................8-bit freerun timer
Timer
0, 1
can be cascade-connected
Timer
2, 3
can be cascade-connected
16-bit
timer
×
1
Timer
7
..................Square-wave output.
16-bit
PWM output (cycle/duty continuous variable). Event count. Pulse width measurement.
Input capture. Square-wave/PWM output to large current terminal P33 possible
Time base timer: One-minute count setting
Watchdog timer
×
1
Watchdog timer
2
×
1
Serial interface
Synchronous type/UART (full-duplex)
×
1:
Serial
0
I/O Pins
I/O
23
:
Common use. Specified pull-up resistor available. Input/output selectable (bit unit)
A/D converter
10-bit
×
5
channels (with S/H)
Special Ports
High-current drive port
ROM Correction
Correcting address designation: Up to
3
addresses possible
Gain Amplifier
2
channels
Reference Power Supply Output
1.7
V: Output to REF17 terminal possible. Supply to A/D converter input, A/D converter reference voltage possible
Reset
Automatic Reset
Internal oscillation
High speed:
8
MHz. Low speed:
20
kHz
MAD00073EEM
Request for your special attention and precautions in using the technical information and
semiconductors described in this book
(1)
If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and
regulations of the exporting country, especially, those with regard to security export control, must be observed.
(2) The technical information described in this book is intended only to show the main characteristics and application circuit examples
of the products. No license is granted in and to any intellectual property right or other right owned by Panasonic Corporation or any
other company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any
other company which may arise as a result of the use of technical information described in this book.
(3) The products described in this book are intended to be used for general applications (such as office equipment, communications
equipment, measuring instruments and household appliances), or for specific applications as expressly stated in this book.
Consult our sales staff in advance for information on the following applications:
–
Special applications (such as for airplanes, aerospace, automotive equipment, traffic signaling equipment, combustion equipment,
life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of
the products may directly jeopardize life or harm the human body.
It is to be understood that our company shall not be held responsible for any damage incurred as a result of or in connection with
your using the products described in this book for any special application, unless our company agrees to your using the products in
this book for any special application.
(4) The products and product specifications described in this book are subject to change without notice for modification and/or im-
provement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product
Standards in advance to make sure that the latest specifications satisfy your requirements.
(5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions
(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute
maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any
defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure
mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire
or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.
(6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,
thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which
damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.
(7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of our company.
20100202
京公网安备 11010802033920号
EEWORLD
