EEWORLDEEWORLDEEWORLD

Part Number

Search

MDCE/3.3S/12D/3.3S

Description
4-OUTPUT 26W DC-DC REG PWR SUPPLY MODULE
CategoryPower/power management    The power supply circuit   
File Size419KB,15 Pages
ManufacturerInterpoint ( Crane Aerospace & Electronics )
Websitehttp://www.interpoint.com
Download Datasheet Parametric View All

MDCE/3.3S/12D/3.3S Overview

4-OUTPUT 26W DC-DC REG PWR SUPPLY MODULE

MDCE/3.3S/12D/3.3S Parametric

Parameter NameAttribute value
MakerInterpoint ( Crane Aerospace & Electronics )
package instruction,
Reach Compliance Codeunknown
ECCN codeEAR99
Analog Integrated Circuits - Other TypesDC-DC REGULATED POWER SUPPLY MODULE
Maximum input voltage40 V
Minimum input voltage16 V
Nominal input voltage28 V
JESD-30 codeR-XDFM-F18
Number of functions1
Output times4
Number of terminals18
Maximum operating temperature100 °C
Minimum operating temperature-55 °C
Maximum output voltage3.33 V
Minimum output voltage3.27 V
Nominal output voltage3.3 V
Package body materialUNSPECIFIED
Package shapeRECTANGULAR
Package formFLANGE MOUNT
Certification statusNot Qualified
surface mountYES
technologyHYBRID
Temperature levelOTHER
Terminal formFLAT
Terminal locationDUAL
Maximum total power output26 W
Fine-tuning/adjustable outputNO
F
EATURES
*
–55° to +100°C operation
16 to 40 VDC input
Two to eight outputs
Fully Isolated
50 V for up to 50 ms transient
protection
Inhibit function
Sync function available on
select modules
Sense available on select
single output modules
Short circuit protection
M
ULTIPLE
O
UTPUT
(2-8),
F
ACTORY
C
ONFIGURABLE
DC/DC C
ONVERTERS
28 V
OLT
I
NPUT
MDC SERIES
UP TO 60 WATTS
VDC O
UTPUT
Mix or match volt-
ages and power to
configure from two
to eight outputs.
Size (max):MDCG-H 3.005 x 1.505 x 0.400 inches (76.33 x 38.23 x 10.16 mm)
MDCA-F 3.005 x 2.260 x 0.400 inches (76.33 x 57.40 x 10.16 mm)
Weight:
MDCG-H 100 grams maximum
MDCA-F 150 grams maximum
Screening: Standard or ES
Description
Interpoint’s MDC Series™ of DC/DC converters offers a unique
product by effectively combining two, three, or four individual
modular DC/DC converters to provide more than one hundred
combinations. The modules are established high-reliability military
aerospace DC/DC converters with input voltages of 16 to 40 VDC
and a typical transient rating of 50 V for 50 milliseconds. All modules
operate from no-load to full load and provide a constant current limit
at each output.
Features
All converters have an inhibit function. Remote sense and trim up to
0.6V is available on the 30 watt single modules. The 15 watt and 30
watt choices have synchronization - if two are used, the synchro-
nization functions are combined internally.
Table 1: Modules – Power and Vout
Power
30 Watt
Vout
3.3
5
12
15
18
±5
±12
±15
3.3
5
5.2
12
15
28
±5
±12
±15
Features
Inhibit &
Sync &
Sense/
Trim up
Inhibit &
Sync
Inhibit &
Sync
1.5 Watt
Power
5 Watt
Vout
5
5.2
12
15
±5
±12
±15
3.3
5
5.2
12
15
±5
±12
±15
Features
Inhibit
15 Watt
Inhibit
1
Four-wheel drive system
Many people may think that four-wheel drive cars will have stronger ground-holding performance. In fact, they confuse the concept of ground-holding performance. The biggest difference between four-whe...
frozenviolet Automotive Electronics
[CoreUtil/General]: Illegal State
IAR compilation error code  Internal Error: [CoreUtil/General]: Illegal StateHas anyone encountered the same problem?...
ykyyky Microcontroller MCU
CC6.1 compile and generate Hex problem
When Enable ARM Hex Utility is not selected, no warning appears during compilation, Debug can run, and the program logic is correct. However, after selecting Enable ARM Hex Utility, multiple warnings ...
kkmugs Microcontroller MCU
Design: Overvoltage protection high-side switch with only four devices
Although MCUs typically run at a low voltage of 3.3V, there are often situations where they need to control a load at a high voltage of 12V. If the MCU cannot be controlled by a low-side switch, a met...
超级电工 MCU
Stories about people being cheated by various housekeepers/antivirus software
Today, someone in the water group called me and said that his cadence was down, and he didn't know why. I suggested to him to check whether his security manager/antivirus software did something bad an...
okhxyyo Talking
How to perform mark verification on the serial port of stm32
Recently, I used mark check in serial communication. I checked and found that the check bit needs to be fixed to 1. I don't know how to set it so that the check bit can be fixed to 1? Experts, please ...
chenbingjy stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2169  1335  548  945  108  44  27  12  20  3 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号