I have a question: I can’t log in to the recent training videos, including the public videos. It becomes the following interface: No matter how I enter the password, it doesn’t work. . . I need help. ...
I am currently learning the bootloader in wince, and I don't understand the eboot code. I want to use single-step tracing, setting breakpoints, etc., but I don't know how to operate. I encountered thi...
The degree of damage caused by static electricity varies according to the type of electronic components. Even the lowest static voltage of 100V can cause damage to them. In recent years, as electronic...
Can I use 555 to provide a clock source for the chip? I use ADC0809 to do analog-to-digital conversion and need to provide a clock signal for the conversion. Can I use 555? What are its advantages and...
I am a novice learning PCB design, and I hope someone can give me some advice. Can you recommend some good reference books? I am a computer major. I know a lot about software, but it is limited. I don...
"Originally, there are many people who can design very good
chips
, but the market does not give domestic
chips
the opportunity to iterate, and domestic companies cannot give engine...[Details]
Regarding the PHY construction of LWIP, the PHY chip used is LAN8720A, RMII mode. Regarding the hardware connection part, the Atomic board F407 is used, and the hardware connection is as follows: ...[Details]
After studying the F4 FSMC method to drive the touch screen for a few days, I have gained some understanding, which are listed below. The unorganized record is only for my own reference in the future...[Details]
China Energy Storage Network:
At the Boao Forum, Zhu Min, the current dean of the National Institute of Finance at Tsinghua University, said: "When talking about blockchain, we must first sep...[Details]
The photovoltaic inverter is the core equipment of the photovoltaic system. Its main function is to convert the direct current generated by the photovoltaic modules into alternating current that meets...[Details]
This paper proposes a design scheme for an embedded CNC system based on ARM and FPGA. The software and hardware design of the ARM system, the implementation method of hardware fine interpolation ...[Details]
The pins of stm32 have two uses: GPIO (general purpose io) and AFIO (alternate function io) For some pins (depending on the chip), neither of these two uses exists. For example, in 64-pin products, O...[Details]
OSC_IN and OSC_OUT are external crystal pins by default. If you do not use an external crystal oscillator on the STM32, how to connect OSC_IN and OSC_OUT If you use the internal RC oscillator instead...[Details]
I have encountered many problems when tinkering with LD driver recently. I will record them one by one below. Otherwise, who will remember who in five hundred years? 1. Configuration issues of multi-...[Details]
Today I am using the AD function of the stm8s microcontroller. There are ten channels from AN0 to AN9 on the microcontroller. I want to use only three of them, AN5 to AN7. //ADC initialization void A...[Details]
1) ADC multi-channel acquisition: (Multi-channel acquisition must use scanning mode. In scanning mode, the channels of the rule group share a register, so DMA transmission must be used; to prevent da...[Details]
Circuit: Using AT89S52 single chip microcomputer. P3.0 to P3.3 are connected to four external buttons. P3.4 to P3.7 are the bit selection ports for controlling the four digital tubes, and P1 is the s...[Details]
Use P1.0 to output 1KHz and 500Hz audio signals to drive the speaker as an alarm signal. It is required that the 1KHz signal sound for 100ms and the 500Hz signal sound for 200ms, alternating between...[Details]
1. SCL is always controlled by the Master. SDA is controlled by the Slave when reading data and by the Master when writing data according to the direction of data transmission. After the 8-bit data i...[Details]
TI Technology Forum
京公网安备 11010802033920号
EEWORLD
