EEWORLDEEWORLDEEWORLD

Part Number

Search

TSOP57236TT2

Description
Photo IC, LINEAR OUTPUT PHOTO DETECTOR
CategoryLED optoelectronic/LED    photoelectric   
File Size246KB,11 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric Compare View All

TSOP57236TT2 Overview

Photo IC, LINEAR OUTPUT PHOTO DETECTOR

TSOP57236TT2 Parametric

Parameter NameAttribute value
MakerVishay
Reach Compliance Codeunknown
Installation featuresSURFACE MOUNT
Maximum operating temperature85 °C
Minimum operating temperature-25 °C
Optoelectronic device typesLINEAR OUTPUT PHOTO IC
Maximum slew rate0.0009 mA
Nominal supply voltage5 V
surface mountYES
TSOP572.., TSOP574..
www.vishay.com
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
FEATURES
• Height of 0.8 mm
• ± 75° half angle sensitivity
• Low supply current
• Photo detectors and preamplifier in one
package
22531-1
• Internal filter for PCM frequency
• Supply voltage: 2.5 V to 5.5 V, typically even
2.0 V to 5.5 V is possible
• Improved immunity against ambient light
• Insensitive to supply voltage ripple and noise
• Material categorization: For definitions of compliance
please see
www.vishay.com/doc?99912
DESCRIPTION
The TSOP572.., TSOP574.. series are miniaturized receiver
modules for infrared remote control systems. A PIN diode
and a preamplifier are assembled on a lead frame, the epoxy
lens cap is designed as an IR filter.
The demodulated output signal can be directly decoded by
a microprocessor. The TSOP572.. is compatible with all
common IR remote control data formats. The TSOP574.. is
optimized to suppress almost all spurious pulses from
energy saving fluorescent lamps but will also suppress
some data signals.
This component has not been qualified according to
automotive specifications.
PARTS TABLE
CARRIER FREQUENCY
36 kHz
38 kHz
40 kHz
56 kHz
STANDARD APPLICATIONS (AGC2)
TSOP57236
TSOP57238
TSOP57240
TSOP57256
VERY NOISY ENVIRONMENTS (AGC4)
TSOP57436
TSOP57438
TSOP57440
TSOP57456
BLOCK DIAGRAM
4, 5
V
S
33 kΩ
1
Input
AGC
Band
pass
Demo-
dulator
OUT
2, 3,
6, 7, 8
PIN
20445-6
APPLICATION CIRCUIT
17170-10
R
1
IR receiver
V
S
Circuit
C
1
OUT
GND
V
O
µC
GND
+ V
S
Transmitter
with
TSALxxxx
Control circuit
GND
The external components R
1
and C
1
are optional
to improve the robustness against electrical overstress
(typical values are R
1
= 100
Ω,
C
1
= 0.1 µF).
Revision: 1.4, 09-Mar-12
1
Document Number: 82434
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000

TSOP57236TT2 Related Products

TSOP57236TT2 TSOP57456TT2 TSOP57256TT2 TSOP57240TT2
Description Photo IC, LINEAR OUTPUT PHOTO DETECTOR Photo IC, LINEAR OUTPUT PHOTO DETECTOR Photo IC, LINEAR OUTPUT PHOTO DETECTOR Photo IC, LINEAR OUTPUT PHOTO DETECTOR
Maker Vishay Vishay Vishay Vishay
Reach Compliance Code unknown unknown unknown unknown
Installation features SURFACE MOUNT SURFACE MOUNT SURFACE MOUNT SURFACE MOUNT
Maximum operating temperature 85 °C 85 °C 85 °C 85 °C
Minimum operating temperature -25 °C -25 °C -25 °C -25 °C
Optoelectronic device types LINEAR OUTPUT PHOTO IC LINEAR OUTPUT PHOTO IC LINEAR OUTPUT PHOTO IC LINEAR OUTPUT PHOTO IC
Maximum slew rate 0.0009 mA 0.0009 mA 0.0009 mA 0.0009 mA
Nominal supply voltage 5 V 5 V 5 V 5 V
surface mount YES YES YES YES
TI C6000 series DSP system initialization and system stack
TI C6000 series DSP system initialization and system stack...
Jacktang Microcontroller MCU
DDK compilation problem
I recently learned about drivers and have a process/thread monitor code. I compiled it successfully, but the following error message appeared when linking: Linking Executable - objfre\i386\pmonitor.sy...
staraa Embedded System
Wanli LPC54102 development board heart rate meter Heartrate application notes routine transplantation analysis
AN11608_Heart-rate Monitor using the Low Power LPC5410x demonstrates the use of LPC54102 and PulseSensorAMped! as a heart rate monitor application. Due to the different settings of the Wanli developme...
mars4zhu NXP MCU
Keil compilation error, probably the library is not fully added, please help me check
What library should I add for the error in the picture? How to add it? This is an external interrupt....
jiangper stm32/stm8
The usbkbd example installation failed, please help me?
There is a usbkdb example in the . I want to see if this driver can be used on my USB keyboard. I modified the vid and pid in the inf (checked with usbviewer, it should be correct), and then clicked U...
tianweiming9527 Embedded System
boring
Hello, newcomers....
li770119 Recruitment

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2090  502  300  2647  592  43  11  7  54  12 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号