EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-GLHSA4121

Description
Transponder, 10000Mbps(Tx), 10000Mbps(Rx), SC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerJDS Uniphase Corporation ( VIAVI )
Websitehttp://www.jdsu.com/index.html
Download Datasheet Parametric View All

PH1-GLHSA4121 Overview

Transponder, 10000Mbps(Tx), 10000Mbps(Rx), SC/UPC Connector,

PH1-GLHSA4121 Parametric

Parameter NameAttribute value
MakerJDS Uniphase Corporation ( VIAVI )
Reach Compliance Codecompliant
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body width56.1 mm
body height13.2 mm
Body length or diameter76.5 mm
Connection TypeSC/UPC CONNECTOR
Data rate (receive)10000 Mbps
Data rate (send)10000 Mbps
Emitter/Detector TypeAVALANCHE PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1559 nm
Nominal optical power output2.511 mW
minimum return loss-27 dB
Sensitivity-24 dBm
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
How can I (beginner) transplant MPEG-4T algorithm (graduation project) using DM642?
Dear experts, I would like to ask you a question. I am using DM642 to transplant MPEG-4 algorithm.After reading the MPEG-2LOOPBACK program in the experiment package, there are many things I don't unde...
esvive DSP and ARM Processors
[AVR] I'm going crazy, can anyone help me with how to use timers T0 and T1 to generate an interval 38k square wave?
I used TO to generate 38k infrared square wave, and used T1 to delay, so that I could generate square wave in segments, and then use the integrated connector to receive it. I found that no matter what...
小猪崽 Embedded System
The problem of "ground" on both sides of the single-ended flyback power supply transformer
The simplified schematic diagram of the single-ended flyback switching power supply, the input voltage is 120-150VAC, as shown in the figure During the debugging process, if you want to observe the se...
shaorc Power technology
Ask the incense master --- PWM input mode minimum frequency problem
I am using the example program PWMINPUT, and I connected a PWM signal to PA0.1. The example program says: The TIMxCLK frequency is set to 72 MHz, the Prescaler is 0 so the TIM2 counter clock is 72 MHz...
huyingguang stm32/stm8
Wonderglass, does my keyboard use the interrupt mode or the scanning mode? Please answer
Wonderglass, does my keyboard use the interrupt mode or the scanning mode? Please answer...
pyy1980 FPGA/CPLD
MCU serial port control color LCD
This driver module can drive 1.3-inch to 15-inch TFT screens. It is very easy to use. Friends who are interested can email me for information. My email address is boy_201a@163.com My phone number is 0...
tianjixian Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2307  2494  2305  1797  1561  47  51  37  32  23 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号