EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-GLPLA388N

Description
Transponder, 10000Mbps(Tx), 10000Mbps(Rx), LC/SPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerJDS Uniphase Corporation ( VIAVI )
Websitehttp://www.jdsu.com/index.html
Download Datasheet Parametric View All

PH1-GLPLA388N Overview

Transponder, 10000Mbps(Tx), 10000Mbps(Rx), LC/SPC Connector,

PH1-GLPLA388N Parametric

Parameter NameAttribute value
MakerJDS Uniphase Corporation ( VIAVI )
Reach Compliance Codeunknown
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body width56.1 mm
body height13.2 mm
Body length or diameter76.5 mm
Connection TypeLC/SPC CONNECTOR
Data rate (receive)10000 Mbps
Data rate (send)10000 Mbps
Emitter/Detector TypePIN PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1554 nm
Nominal optical power output1.584 mW
minimum return loss-27 dB
Sensitivity-17 dBm
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
MAXIM CCFL/LED Backlight Driver IC Application Column
[i=s]This post was last edited by jameswangsynnex on 2015-3-3 19:59[/i] [size=13px]MAXIM's DS391, DS3992, DS3994, DS3988, MAX8729, and MAX8751 provide a complete solution from single lamp to 32 lamps....
bilwayleo Mobile and portable
PC and wince synchronization problem
I use a desktop computer to connect to Advantech 6552 industrial control board WinCE system through a dual-machine interconnection cable. The desktop computer's IP is 192.168.0.12 and the industrial c...
酒壶 Embedded System
Selection of Typical Design Examples of Switching Power Supplies
"Selected Typical Design Examples of Switching Power Supplies" is divided into eight chapters. Chapter 1 briefly introduces four typical design examples of PFC, Chapter 2 systematically introduces the...
arui1999 Download Centre
Newbie's questions about GPIO ports
I now think that GPIO ports are actually some parallel ports derived from MCU. I wonder if my view is correct? If so, what kind of parallel ports can be used as GPIO ports? To pull a GPIO high or low,...
zgl7903 Embedded System
LCD12232 LCD driver help
I use JM12232F LCD, the connection interface is a parallel port with RS, RW, EN pins. I don't know how to write it, so I hope someone can contribute a program! It's best to have easy-to-understand com...
anghost MCU
ATmega48 output PWM waveform is incorrect, please see the picture
The output needs to be reset to zero every 10 milliseconds. Does anyone have the same problem? #include iom48v.h #include macros.h void main(void) {DDRD |= 0x20;TCCR0A = 0x23; TCCR0B = 0x0B; OCR0A = 5...
lewise88 Microchip MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 623  1643  166  1550  2356  13  34  4  32  48 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号