EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-NLALA2925

Description
Transponder, LC/SPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerJDS Uniphase Corporation ( VIAVI )
Websitehttp://www.jdsu.com/index.html
Download Datasheet Parametric View All

PH1-NLALA2925 Overview

Transponder, LC/SPC Connector,

PH1-NLALA2925 Parametric

Parameter NameAttribute value
MakerJDS Uniphase Corporation ( VIAVI )
Reach Compliance Codeunknown
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body width56.1 mm
body height13.2 mm
Body length or diameter76.5 mm
Communication standardsOC-192, SONET
Connection TypeLC/SPC CONNECTOR
Emitter/Detector TypeAVALANCHE PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1535 nm
Nominal optical power output1.584 mW
minimum return loss-27 dB
Sensitivity-24 dBm
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
I am a self-recommended intern. I am a junior. I have learned and I hope the seniors can give me some advice.
My university is a very unremarkable university in the electronics industry. My major is electronic information science and technology. I am a third-year college graduate and have not passed the Level...
yrloy Integrated technical exchanges
[EBOOT transplant] DRAM memory address configuration issues
I would like to ask you the following questions, and I hope you can give me some advice. [Problem description] When using the development board with Samsung V210 chip, running EBOOT+wince6.0 can run, ...
wangpu719 Embedded System
Stellaris M3 selection table, including chip series (Tempest, Sandstorm..)
The attachment is the TI Stellaris M3 chip selection table, which contains the correspondence between various chips and which series they correspond to. Many customers may not know which series of chi...
limo Microcontroller MCU
How to implement nested assembly interrupt functions
How to implement nested assembly interrupt functionHow to implement the entry and program processing of interrupt function using assembly? ? ? ? ?...
guangtonggg Microcontroller MCU
Help: vxsim debugging problem
Help: Large program cannot be debugged under vxsim. 1. My small program can be debugged, which means my basic options should be correct. 2. I have set the memory size of vxsim to be large enough. 3. T...
SDFSADFSAD Embedded System
8-bit data latch 74HC573 application example
1. 74HC573 is an 8-bit data latch. Mainly used for the control of digital tubes, buttons, etc. 573 has two functions: 1) Data latch. When the input data disappears, the data is still maintained at the...
灞波儿奔 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 655  862  1210  2685  351  14  18  25  55  8 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号