Specifications for Rad Hard QML devices are controlled by the
Defense Supply Center in Columbus (DSCC). The SMD numbers
listed below must be used when ordering.
Detailed Electrical Specifications for the HS-303ARH,
HS-303AEH, HS-303BRH, HS-303BEH are contained in
SMD
5962-95813.
A “hot-link” is provided from our website for
downloading
Functional Diagram
IN
N
P
D
Pin Configurations
HS1-303ARH, HS-303BRH
(SBDIP), CDIP2-T14
TOP VIEW
NC
S3
D3
D1
1
2
3
4
5
6
7
14 V+
13 S4
12 D4
11 D2
10 S2
9 IN2
8 V-
TRUTH TABLE
LOGIC
0
1
SW1 AND SW2
OFF
ON
SW3 AND SW4
ON
OFF
S1
IN1
GND
HS-303ARH, HS-303AEH, HS-303BRH, HS-303BEH
(FLATPACK) CDFP3-F14
TOP VIEW
1
NC
S3
D3
D1
S1
IN1
GND
3
4
5
6
7
12
11
10
9
8
2
14
13
V+
S4
D4
D2
S2
IN2
V-
December 12, 2012
FN6411.2
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774
|
Copyright Intersil Americas Inc. 2006, 2008, 2012. All Rights Reserved
Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners.
HS-303ARH, HS-303AEH, HS-303BRH, HS-303BEH
Ordering Information
ORDERING NUMBER
(Note)
5962F9581304QCC
5962F9581304QXC
5962F9581304V9A
5962F9581306V9A
5962F9581304VCC
5962F9581306VCC
5962F9581304VXC
HS0-303ARH/SAMPLE
HS1-303ARH/PROTO
HS9-303ARH/PROTO
5962F9581306VXC
5962F9581305QCC
5962F9581305QXC
5962F9581305V9A
5962F9581307V9A
5962F9581305VCC
5962F9581307VCC
5962F9581305VXC
HS0-303BRH/SAMPLE
HS1-303BRH/PROTO
HS9-303BRH/PROTO
5962F9581307VXC
PART NUMBER
HS1-303ARH-8
HS9-303ARH-8
HS0-303ARH-Q
HS0-303AEH-Q
HS1-303ARH-Q
HS1-303AEH-Q
HS9-303ARH-Q
HS0-303ARH/SAMPLE
HS1-303ARH/PROTO
HS9-303ARH/PROTO
HS9-303AEH-Q
HS1-303BRH-8
HS9-303BRH-8
HS0-303BRH-Q
HS0-303BEH-Q
HS1-303BRH-Q
HS1-303BEH-Q
HS9-303BRH-Q
HS0-303BRH/SAMPLE
HS1-303BRH/PROTO
HS9-303BRH/PROTO
HS9-303BEH-Q
TEMP. RANGE
(°C)
-55 to +125
-55 to +125
-55 to +125
-55 to +125
-55 to +125
-55 to +125
-55 to +125
-55 to +125
-55 to +125
-55 to +125
-55 to +125
-55 to +125
-55 to +125
-55 to +125
-55 to +125
-55 to +125
-55 to +125
-55 to +125
-55 to +125
-55 to +125
-55 to +125
-55 to +125
14 LD SBDIP
14 LD Flatpack
14 LD Flatpack
D14.3
K14.A
K14.A
14 LD SBDIP
14 LD Flatpack
14 LD Flatpack
14 LD SBDIP
14 LD Flatpack
14 LD SBDIP
14 LD SBDIP
14 LD SBDIP
14 LD SBDIP
14 LD Flatpack
D14.3
K14.A
K14.A
D14.3
K14.A
D14.3
D14.3
D14.3
D14.3
K14.A
14 LD SBDIP
14 LD Flatpack
14 Ld SBDIP
14 Ld SBDIP
14 LD SBDIP
14 LD SBDIP
14 LD Flatpack
PKG.
PKG.
DWG. #
D14.3
K14.A
D14.3
D14.3
D14.3
D14.3
K14.A
NOTE: These Intersil Pb-free Hermetic packaged products employ 100% Au plate - e4 termination finish, which is RoHS compliant and compatible with
both SnPb and Pb-free soldering operations.
2
FN6411.2
December 12, 2012
HS-303ARH, HS-303AEH, HS-303BRH, HS-303BEH
Die Characteristics
DIE DIMENSIONS:
2690µm x 5200µm (106mils x 205mils)
Thickness: 483µm
±
25.4µm (19mils
±
1mil)
Substrate:
Radiation Hardened Silicon Gate,
Dielectric Isolation
Backside Finish:
Silicon
INTERFACE MATERIALS:
Glassivation:
Type: PSG (Phosphorous Silicon Glass)
Thickness: 8.0k
Å
±
1.0k
Å
Top Metallization:
Type: AlSiCu
Thickness: 16.0k
Å
±
2k
Å
ASSEMBLY RELATED INFORMATION:
Substrate Potential:
Unbiased (DI)
ADDITIONAL INFORMATION:
Worst Case Current Density:
<2.0 x 10
5
A/cm
2
Transistor Count:
196
Metallization Mask Layout
HS-303ARH, HS-303AEH, HS-303BRH, HS-303BEH
IN2
V-
V+
GND
IN1
D4
D2
S4
S2
S1
S3
For additional products, see
www.intersil.com/product_tree
Intersil products are manufactured, assembled and tested utilizing ISO9000 quality systems as noted
in the quality certifications found at
www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time
without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be
accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third
parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see
www.intersil.com
3
D3
D1
FN6411.2
December 12, 2012
HS-303ARH, HS-303AEH, HS-303BRH, HS-303BEH
Ceramic Dual-In-Line Metal Seal Packages (SBDIP)
c1
-A-
-D-
BASE
METAL
b1
M
(b)
SECTION A-A
(c)
LEAD FINISH
D14.3
MIL-STD-1835 CDIP2-T14 (D-1, CONFIGURATION C)
14 LEAD CERAMIC DUAL-IN-LINE METAL SEAL PACKAGE
INCHES
SYMBOL
A
b
b1
b2
MIN
-
0.014
0.014
0.045
0.023
0.008
0.008
-
0.220
MAX
0.200
0.026
0.023
0.065
0.045
0.018
0.015
0.785
0.310
MILLIMETERS
MIN
-
0.36
0.36
1.14
0.58
0.20
0.20
-
5.59
MAX
5.08
0.66
0.58
1.65
1.14
0.46
0.38
19.94
7.87
2.54 BSC
7.62 BSC
3.81 BSC
3.18
0.38
0.13
0.13
90
o
-
-
-
-
14
5.08
1.52
-
-
105
o
0.38
0.76
0.25
0.038
NOTES
-
2
3
-
4
2
3
-
-
-
-
-
-
5
6
7
-
-
-
-
2
8
Rev. 0 4/94
E
M
-B-
bbb S
C A-B S
D
BASE
PLANE
SEATING
PLANE
S1
b2
b
ccc M C A - B S
A A
S2
-C-
Q
A
L
D S
b3
c
c1
e
A
e
D S
D
E
e
A/2
c
e
eA
eA/2
0.100 BSC
0.300 BSC
0.150 BSC
0.125
0.015
0.005
0.005
90
o
-
-
-
-
14
0.200
0.060
-
-
105
o
0.015
0.030
0.010
0.0015
aaa
M C A - B S D S
NOTES:
1. Index area: A notch or a pin one identification mark shall be located ad-
jacent to pin one and shall be located within the shaded area shown.
The manufacturer’s identification shall not be used as a pin one identi-
fication mark.
2. The maximum limits of lead dimensions b and c or M shall be measured
at the centroid of the finished lead surfaces, when solder dip or tin plate
lead finish is applied.
3. Dimensions b1 and c1 apply to lead base metal only. Dimension M
applies to lead plating and finish thickness.
4. Corner leads (1, N, N/2, and N/2+1) may be configured with a partial
lead paddle. For this configuration dimension b3 replaces dimension
b2.
5. Dimension Q shall be measured from the seating plane to the base plane.
6. Measure dimension S1 at all four corners.
7. Measure dimension S2 from the top of the ceramic body to the nearest
metallization or lead.
8. N is the maximum number of terminal positions.
9. Braze fillets shall be concave.
10. Dimensioning and tolerancing per ANSI Y14.5M - 1982.
11. Controlling dimension: INCH.
L
Q
S1
S2
α
aaa
bbb
ccc
M
N
4
FN6411.2
December 12, 2012
HS-303ARH, HS-303AEH, HS-303BRH, HS-303BEH
Ceramic Metal Seal Flatpack Packages (Flatpack)
A
K14.A
MIL-STD-1835 CDFP3-F14 (F-2A, CONFIGURATION B)
14 LEAD CERAMIC METAL SEAL FLATPACK PACKAGE
INCHES
SYMBOL
MIN
0.045
0.015
0.015
0.004
0.004
-
0.235
-
0.125
0.030
0.050 BSC
0.008
0.270
0.026
0.005
-
14
0.015
0.370
0.045
-
0.0015
0.20
6.86
0.66
0.13
-
14
MAX
0.115
0.022
0.019
0.009
0.006
0.390
0.260
0.290
-
-
MILLIMETERS
MIN
1.14
0.38
0.38
0.10
0.10
-
5.97
-
3.18
0.76
1.27 BSC
0.38
9.40
1.14
-
0.04
MAX
2.92
0.56
0.48
0.23
0.15
9.91
6.60
7.11
-
-
NOTES
-
-
-
-
-
3
-
3
-
7
-
2
-
8
6
-
-
Rev. 0 5/18/94
e
PIN NO. 1
ID AREA
A
-A-
-B-
D
A
b
S1
b
E1
b1
c
c1
D
0.004
Q
A
-C-
M H A-B S
D S
E
0.036
M H A-B S
C
-D-
D S
E
E1
E2
-H-
L
E3
E2
E3
LEAD FINISH
L
E3
e
k
L
SEATING AND
BASE PLANE
c1
BASE
METAL
b1
M
M
(b)
SECTION A-A
(c)
Q
S1
M
N
NOTES:
1. Index area: A notch or a pin one identification mark shall be located ad-
jacent to pin one and shall be located within the shaded area shown.
The manufacturer’s identification shall not be used as a pin one identi-
fication mark. Alternately, a tab (dimension k) may be used to identify
pin one.
2. If a pin one identification mark is used in addition to a tab, the limits of
dimension k do not apply.
3. This dimension allows for off-center lid, meniscus, and glass overrun.
4. Dimensions b1 and c1 apply to lead base metal only. Dimension M ap-
plies to lead plating and finish thickness. The maximum limits of lead
dimensions b and c or M shall be measured at the centroid of the fin-
ished lead surfaces, when solder dip or tin plate lead finish is applied.
5. N is the maximum number of terminal positions.
6. Measure dimension S1 at all four corners.
7. For bottom-brazed lead packages, no organic or polymeric materials
shall be molded to the bottom of the package to cover the leads.
8. Dimension Q shall be measured at the point of exit (beyond the menis-
cus) of the lead from the body. Dimension Q minimum shall be reduced
by 0.0015 inch (0.038mm) maximum when solder dip lead finish is
applied.
9. Dimensioning and tolerancing per ANSI Y14.5M - 1982.
Newbie help: I am working as a network administrator now, and I want to learn embedded systems, but I don’t know what the future holds, and what knowledge I should learn. I have basically no foundatio...
#includevoid main(void)
{WDTCTL=WDTPW+WDTHOLD;// stop watchdogTACTL=TASSEL0+TACLR;//ACLK,CLEAR TARCCTL0=CCIE;//CCR0 INT ENCCR0=16384;//32KHZ,=0.5SP4DIR|=BIT0;//p4.0 is out;P4DIR|=BIT1;//p4.1 is out;P4...
The competition topic is as shown below, and the full version can be downloaded from Baidu Library. The main question is the red part in the picture. Question 1: How to get the third harmonic? I used ...
Hello everyone, which company in China can provide PGA309EVM and technical support for PGA309? I am working on PGA309 chip recently. If you know, please let me know, thank you....
A very simple key function, I used 51 and avr to do it before, the functions are very ideal. Now I use PIC16F877. When pressing each key, the corresponding number is displayed on the digital tube. The...
According to foreign media reports, Ford Motor has applied to the U.S. Patent and Social Security Administration (USPTO) for a patent for a remote vehicle control system that may be used in future ...[Details]
From being a global leader to losing the market, Korean battery manufacturers have always wanted to regain the lost market and dignity, but facing Chinese battery manufacturers represented by CAT...[Details]
On August 22, the National Energy Administration released the latest data, showing that by the end of July 2025, China's total number of electric vehicle charging infrastructure will reach 16.696 m...[Details]
In the electronics manufacturing industry, surface mount technology (SMT) placement machines are core equipment for production lines. However, with many different models available on the market, ch...[Details]
Chinese characters are extensive and profound, and there are many different names for ESD tubes. How many of them do you know?
As far as I know, ESD diodes are currently known as ESD p...[Details]
Teletrac Navman has launched the Multi IQ dashcam, a cloud-based solution designed for large commercial vehicle operators. It connects up to five cameras to cover the vehicle's interior, sides, and...[Details]
Common methods for troubleshooting roller press bearing wear include repair welding, thermal spraying, brush plating, and scrapping and replacement. However, these methods are often subject to asse...[Details]
When American cartoonist Chester Gould sketched the watch on Dick Tracy's wrist, he had no idea that science fiction would become reality 70 years later. As a comic strip artist, Gould imagined fut...[Details]
Pure electric vehicles have experienced rapid growth in recent years, and many consumers now consider them as a top choice when purchasing a car. But do you know how to choose a satisfactory and sa...[Details]
A Beijing chemical project utilizes a distributed control system (DCS). The master control system primarily uses the Modbus protocol, while the remote field devices utilize the PROFIBUS-DP protocol...[Details]
According to the latest financial report data, thanks to its leading position in advanced technology, TSMC's profit performance in the second quarter of 2025 was extremely impressive, with net prof...[Details]
The term "remote meter reading" literally emphasizes remoteness. But how far is remote? One kilometer? Two kilometers? Those aren't considered far at all. Currently, the longest distance for ...[Details]
1. Output power. Rated power (RMS): Rated power refers to the sinusoidal alternating power that the amplifier can withstand for a long time. Maximum undistorted power...
2. Frequency response:...[Details]
Recently, Orbbec issued an announcement that its application for issuing A-shares to specific objects in 2025 has been accepted by the Shanghai Stock Exchange.
The announcement shows that the ...[Details]
IPTV, commonly referred to as digital television, has both similarities and differences.
1. Technical System:
The IPTV system, also known as interactive television, primarily consis...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
