As the title says!!! It is best to write the company name and contact information. If it is good, you can refer to it. If it is not good, you will not be fooled again....
Features: Small beam angle and high measurement accuracy; Small size, integrated compact structure design;The wall-mounted design does not require holes to be opened in the container, ensuring the con...
I've been tinkering with 8266 these past two days, trying to re-burn the firmware. I'm using ESP-12-Q, which can be found on Taobao and is everywhere. The problem I'm encountering now is as shown in t...
When using a ferroelectric RTC, I found that the seconds bit of the clock is not timing correctly at all. The data appears completely randomly, but it will definitely jump after a certain interval. Th...
If PADS is not installed properly and cannot be cracked, there will be no save function. I recently installed PADS9.1 at home and it went smoothly. The same file did not work at the installation unit,...
[i=s]This post was last edited by jameswangsynnex on 2015-3-3 20:00[/i] TN-type liquid crystal display principle TN-type liquid crystal display technology can be said to be the most basic among liquid...
In
circuit design,
current
measurement
is widely used, and the main fields are divided into three categories: in measurement,
the electric meter
is used to measure the curre...[Details]
Remote keyless entry (RKE) systems have become popular with users, with more than 80% of new cars in North America and more than 70% in Europe equipped with RKE systems. In addition to the obvious ...[Details]
Analog engineers have traditionally struggled with complexity when designing power supplies that required multiple outputs, dynamic load sharing, hot-swap, or extensive fault-handling capabilities....[Details]
The reason for the light decay of white LEDs: the decline of phosphor performance
So far, the rapid decline of the luminous performance of white light LEDs, especially low-power white light LE...[Details]
Nippon Electric Works and Volvo Technology Japan have developed a wireless power supply system for electric vehicles (EVs). Using this system, the two companies have successfully conducted an exper...[Details]
This article will introduce a design method for a distributed control system used in a tracking car, which can perform distributed control of motor modules, sensor modules, and lighting control mod...[Details]
0 Introduction
Wireless Sensor Network (WSN) monitors the target by deploying a large number of sensor nodes in the target area. WSN realizes the positioning and tracking of the target, determi...[Details]
1 Overview
In the field of traditional lighting, the concepts and definitions of lamps and lamps are clear. Lamps and lamps have their own applicable product standards, supporting technical st...[Details]
Energy conservation and environmental protection are the main directions of current automotive technology research, and power batteries are the key to electric vehicle technology. Research on powe...[Details]
UDN2916LB is a two-phase stepper motor bipolar driver integrated circuit launched by SANKEN. It can drive dual-winding bipolar stepper motors and is particularly suitable for controlling dual-step ...[Details]
Some people believe that hybrid vehicles are just a transitional product, and the ultimate goal of developing new energy vehicles is electric vehicles. Therefore, China should skip hybrid vehicles ...[Details]
SL11R is a 16-bit RISC microcontroller with a USB interface produced by Scanlogic. Its core processing speed reaches 48MIPS. It has rich hardware resources and 32-bit programmable I/O ports, and ca...[Details]
Automotive electronics are in a noisy environment
,
so automotive electronics must have excellent electromagnetic compatibility (EMC) performance. The most important part of automotive elec...[Details]
Abstract: Based on FPGA hardware, the image scaling with fixed magnification is realized. The 2D convolution operation is decomposed into 2 1D convolution operations. The input original image pixel...[Details]
Workers in garment factories usually turn on the power of the sewing machine motor as soon as they get to work and do not turn off the sewing machine power until they get off work. In fact, during ...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
