DATASHEET
X9258
Low Noise/Low Power/2-Wire Bus/256 Taps Quad Digital Controlled
Potentiometers (XDCP™)
The X9258 integrates 4 digitally controlled potentiometers
(XDCP™) on a monolithic CMOS integrated circuit.
The digitally controlled potentiometer is implemented using
255 resistive elements in a series array. Between each
element are tap points connected to the wiper terminal
through switches. The position of the wiper on the array is
controlled by the user through the 2-wire bus interface. Each
potentiometer has associated with it a volatile Wiper Counter
Register (WCR) and 4 non-volatile Data Registers
(DR0:DR3) that can be directly written to and read by the
user. The contents of the WCR controls the position of the
wiper on the resistor array though the switches. Power-up
recalls the contents of DR0 to the WCR.
The XDCP™ can be used as a three-terminal potentiometer
or as a two-terminal variable resistor in a wide variety of
applications including control, parameter adjustments, and
signal processing.
FN8168
Rev 6.00
December 15, 2011
Features
• Four potentiometers in one package
• 256 resistor taps/potentiometer................. 0.4% resolution
• 2-wire serial interface
• Wiper resistance, 40Ωtypical @ V+ = 5V, V- = -5V
• Four nonvolatile data registers for each potentiometer
• Nonvolatile storage of wiper position
• Standby current <5µA max (total package)
• Power supplies
- V
CC
= 2.7V to 5.5V
- V+ = 2.7V to 5.5V
- V- = -2.7V to -5.5V
• 100kΩ, 50kΩtotal potentiometer resistance
• High reliability
- Endurance: 100,000 data changes per bit per register
- Register data retention . . . . . . . . . . . . . . . . . . 100 years
• 24 Ld SOIC, 24 Ld TSSOP
• Dual supply version of X9259
• Pb-free (RoHS compliant)
Block Diagram
V
CC
V
SS
V+
V-
WP
SCL
SDA
A0
A1
A2
A3
INTERFACE
AND
CONTROL
CIRCUITRY
R
2
R
3
R
0
R
1
WIPER
COUNTER
REGISTER
(WCR)
POT 0
V
H0
/R
H0
R
0
R
1
WIPER
COUNTER
REGISTER
(WCR)
V
H2
/R
H2
RESISTOR
ARRAY
POT 2
V
L0
/R
L0
V
W0
/R
W0
R
2
R
3
V
L2
/R
L2
V
W2
/R
W2
8
DATA
R
0
R
1
WIPER
COUNTER
REGISTER
(WCR)
V
W1
/R
W1
V
H1
/R
H1
R
0
R
1
V
W3
/R
W3
WIPER
COUNTER
REGISTER
(WCR)
V
H3
/R
H3
RESISTOR
ARRAY
POT 1
R
2
R
3
RESISTOR
ARRAY
POT 3
V
L1
/R
L1
R
2
R
3
V
L3
/R
L3
FN8168 Rev 6.00
December 15, 2011
Page 1 of 19
X9258
X9258
Ordering Information
PART NUMBER
(Note 2)
X9258US24Z (Note 1)
X9258US24IZ (Note 1)
X9258UV24IZ
X9258TS24Z
X9258TS24IZ (Note 1)
PART
MARKING
X9258US Z
X9258US ZI
X9258UV ZI
X9258TS Z
X9258TS ZI
2.7 to 5.5
50
100
V
CC
LIMITS
(V)
5 ±10
POTENTIOMETER TEMPERATURE
RANGE
ORGANIZATION
(°C)
(kΩ)
50
0 to +70
-40 to +85
-40 to +85
0 to +70
-40 to +85
0 to +70
-40 to +85
-40 to +85
100
0 to +70
-40 to +85
-40 to +85
0 to +70
PACKAGE
(Pb-free)
24 Ld SOIC (300 mil)
24 Ld SOIC (300 mil)
24 Ld TSSOP (4.4mm)
24 Ld SOIC (300 mil)
24 Ld SOIC (300 mil)
24 Ld SOIC (300 mil)
24 Ld SOIC (300 mil)
24 Ld TSSOP (4.4mm)
24 Ld SOIC (300 mil)
24 Ld SOIC (300 mil)
24 Ld TSSOP (4.4mm)
24 Ld TSSOP (4.4mm)
PKG.
DWG. #
M24.3
M24.3
MDP0044
M24.3
M24.3
M24.3
M24.3
MDP0044
M24.3
M24.3
MDP0044
MDP0044
X9258US24Z-2.7 (Note 1) X9258US ZF
X9258US24IZ-2.7 (Note 1) X9258US ZG
X9258UV24IZ-2.7
X9258UV ZG
X9258TS24Z-2.7 (Note 1) X9258TS ZF
X9258TS24IZ-2.7 (Note 1) X9258TS ZG
X9258TV24IZ-2.7
X9258TV24Z-2.7
NOTES:
X9258TV ZG
X9258TV ZF
1. Add “T*” suffix for tape and reel. Please refer to
TB347
for details on reel specifications.
2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte
tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil
Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
3. For Moisture Sensitivity Level (MSL), please see device information page for
X9258.
For more information on MSL please see tech brief
TB363.
FN8168 Rev 6.00
December 15, 2011
Page 2 of 19
X9258
X9258
X9258
(24 LD SOIC, TSSOP)
TOP VIEW
NC
A0
V
W3
/R
W3
V
H3
/R
H3
V
L3
/R
L3
V+
V
CC
V
L0
/R
L0
V
H0
/R
H0
V
W0
/R
W0
A2
WP
1
2
3
4
5
6
7
8
9
10
11
12
X9258
24
23
22
21
20
19
18
17
16
15
14
13
A3
SCL
V
L2
/R
L2
V
H2
/R
H2
V
W2
/R
W2
V–
V
SS
V
W1
/R
W1
V
H1
/R
H1
V
L1
/R
L1
A1
SDA
Pinout
Pin Descriptions
Host Interface Pins
SERIAL CLOCK (SCL)
The SCL input is used to clock data into and out of the X9258.
SERIAL DATA (SDA)
SDA is a bidirectional pin used to transfer data into and out of
the device. It is an open drain output and may be wire-ORed
with any number of open drain or open collector outputs. An
open drain output requires the use of a pull-up resistor. For
selecting typical values, refer to “Guidelines for Calculating
Typical Values of Bus Pull-Up Resistors” on page 10.
DEVICE ADDRESS (A
0
-
A
3
)
The Address inputs are used to set the least significant 4 bits
of the 8-bit slave address. A match in the slave address serial
data stream must be made with the address input in order to
initiate communication with the X9258. A maximum of 16
devices may occupy the 2-wire serial bus.
Pin Names
SYMBOL
SCL
SDA
A0 thru A3
V
H0
/R
H0
thru V
H3
/R
H3
,
V
L0
/R
L0
thru V
L3
/R
L3
V
W0
/R
W0
thru V
W3
/R
W3
WP
V+, V-
V
CC
V
SS
NC
DESCRIPTION
Serial Clock
Serial Data
Device Address
Potentiometer Pins
(terminal equivalent)
Potentiometers Pins
(wiper equivalent)
Hardware Write Protection
Analog Supplies
System Supply Voltage
System Ground
No Connection (Allowed)
Principles Of Operation
The X9258 is a highly integrated microcircuit incorporating four
resistor arrays and their associated registers and counters and
the serial interface logic providing direct communication
between the host and the DCP potentiometers.
Potentiometer Pins
V
H
/R
H
(V
H0
/R
H0
- V
H3
/R
H3
), V
L
/R
L
(V
L0
/R
L0
- V
L3
/R
L3
)
The V
H
/R
H
and V
L
/R
L
inputs are equivalent to the terminal
connections on either end of a mechanical potentiometer.
V
W
/R
W
(V
W0
/R
W0
- V
W3
/R
W3
)
The wiper outputs are equivalent to the wiper output of a
mechanical potentiometer.
Serial Interface (2-Wire)
The X9258 supports a bidirectional bus oriented protocol. The
protocol defines any device that sends data onto the bus as a
transmitter and the receiving device as the receiver. The
device controlling the transfer is a master and the device being
controlled is the slave. The master will always initiate data
transfers and provide the clock for both transmit and receive
operations. Therefore, the X9258 will be considered a slave
device in all applications.
Hardware Write Protect Input (WP)
The WP pin when low prevents nonvolatile writes to the Data
Registers.
Analog Supplies V+, V-
The Analog Supplies V+, V- are the supply voltages for the
DCP analog section.
FN8168 Rev 6.00
December 15, 2011
Page 3 of 19
X9258
Clock and Data Conventions
X9258
Device Addressing
Following a start condition the master must output the address
of the slave it is accessing. The most significant 4 bits of the
slave address are the device type identifier (refer to Figure 1).
For the X9258 this is fixed as 0101[B].
DEVICE TYPE
IDENTIFIER
Data states on the SDA line can change only during SCL LOW
periods (t
LOW
). SDA state changes during SCL HIGH are
reserved for indicating start and stop conditions.
Start Condition
All commands to the X9258 are preceded by the start
condition, which is a HIGH to LOW transition of SDA while SCL
is HIGH (t
HIGH
). The X9258 continuously monitors the SDA
and SCL lines for the start condition and will not respond to any
command until this condition is met.
0
1
0
1
A3
A2
A1
A0
Stop Condition
All communications must be terminated by a stop condition,
which is a LOW to HIGH transition of SDA while SCL is HIGH.
DEVICE ADDRESS
FIGURE 1. SLAVE ADDRESS
Acknowledge
Acknowledge is a software convention used to provide a
positive handshake between the master and slave devices on
the bus to indicate the successful receipt of data. The
transmitting device, either the master or the slave, will release
the SDA bus after transmitting 8 bits. The master generates a
ninth clock cycle and during this period the receiver pulls the
SDA line LOW to acknowledge that it successfully received the
8 bits of data.
The X9258 will respond with an acknowledge after recognition
of a start condition and its slave address and once again after
successful receipt of the command byte. If the command is
followed by a data byte, the X9258 will respond with a final
acknowledge.
The next 4 bits of the slave address are the device address.
The physical device address is defined by the state of the A0
thru A3 inputs. The X9258 compares the serial data stream
with the address input state; a successful compare of all
4 address bits is required for the X9258 to respond with an
acknowledge. The A
0
thru A
3
inputs can be actively driven by
CMOS input signals or tied to V
CC
or V
SS
.
Acknowledge Polling
The disabling of the inputs (during the internal nonvolatile write
operation), can be used to take advantage of the typical 5ms
nonvolatile write cycle time. Once the stop condition is issued
to indicate the end of the nonvolatile write command, the
X9258 initiates the internal write cycle. ACK polling can be
initiated immediately. This involves issuing the start condition
followed by the device slave address. If the X9258 is still busy
with the write operation, no ACK will be returned. If the X9258
has completed the write operation an ACK will be returned and
the master can then proceed with the next operation.
Array Description
The X9258 is comprised of four resistor arrays. Each array
contains 255 discrete resistive segments that are connected in
series. The physical ends of each array are equivalent to the
fixed terminals of a mechanical potentiometer (V
H
/R
H
and
V
L
/R
L
inputs).
At both ends of each array and between each resistor segment
is a CMOS switch connected to the wiper (V
W
) output. Within
each individual array only one switch may be turned on at a
time. These switches are controlled by the Wiper Counter
Register (WCR). The 8 bits of the WCR are decoded to select,
and enable, one of 256 switches.
The WCR may be written directly, or it can be changed by
transferring the contents of one of four associated data
registers into the WCR. These data registers and the WCR can
be read and written by the host system.
FN8168 Rev 6.00
December 15, 2011
Page 4 of 19
X9258
ACK Polling Sequence
NONVOLATILE WRITE
COMMAND COMPLETED
ENTER ACK POLLING
X9258
.
REGISTER
SELECT
I3
I2
I1
I0
R1
R0
P1
P0
INSTRUCTIONS
ISSUE
START
WIPER COUNTER
REGISTER SELECT
FIGURE 2. INSTRUCTION BYTE FORMAT
ISSUE SLAVE
ADDRESS
ISSUE STOP
ACK
RETURNED?
YES
NO
The four high order bits define the instruction. The next 2 bits
(R1 and R0) select one of the four registers that is to be acted
upon when a register oriented instruction is issued. The last
bits (P1, P0) select which one of the four potentiometers is to
be affected by the instruction.
Four of the nine instructions end with the transmission of the
instruction byte. The basic sequence is illustrated in Figure 3.
These two-byte instructions exchange data between the Wiper
Counter Register and one of the data registers. A transfer from
a Data Register to a Wiper Counter Register is essentially a
write to a static RAM. The response of the wiper to this action
will be delayed t
WRL
. A transfer from the Wiper Counter
Register (current wiper position), to a data register is a write to
nonvolatile memory and takes a minimum of t
WR
to complete.
The transfer can occur between one of the four potentiometers
and one of its associated registers; or it may occur globally,
wherein the transfer occurs between all of the potentiometers
and one of their associated registers.
Four instructions require a three-byte sequence to complete.
These instructions transfer data between the host and the
X9258; either between the host and one of the data registers or
directly between the host and the Wiper Counter Register.
These instructions are: Read Wiper Counter Register (read the
current wiper position of the selected potentiometer), Write
Wiper Counter Register (change current wiper position of the
selected potentiometer), Read Data Register (read the
contents of the selected nonvolatile register) and Write Data
Register (write a new value to the selected data register). The
sequence of operations is shown in Figure 4.
FURTHER
OPERATION?
NO
YES
ISSUE
INSTRUCTION
ISSUE STOP
PROCEED
PROCEED
Instruction Structure
The next byte sent to the X9258 contains the instruction and
register pointer information. The four most significant bits are
the instruction. The next four bits point to one of the two
potentiometers and when applicable they point to one of four
associated registers. The format is shown in Figure 2.
SCL
SDA
S
T
A
R
T
0
1
0
1
A3
A2
A1
A0
A
C
K
I3
I2
I1
I0
R1
R0
P1
P0
A
C
K
S
T
O
P
FIGURE 3. TWO-BYTE INSTRUCTION SEQUENCE
FN8168 Rev 6.00
December 15, 2011
Page 5 of 19
京公网安备 11010802033920号
EEWORLD
