The AP3842/3/4/5 family of control ICs provides the
necessary features to implement off-line or DC to
DC fixed frequency current mode control schemes
with a minimal external parts count. Internally
implemented circuits include under voltage lockout
featuring start-up current less than 0.5 mA, a
precision reference trimmed for accuracy at the
error amp input, logic to insure latched operation, a
PWM comparator which also provides current limit
control, and a totem pole output stage designed to
source or sink high peak current. The output stage,
suitable for driving N-Channel MOSFETs, is low in
the off-state.
Differences between members of this family are the
under-voltage lockout thresholds and maximum
duty cycle ranges. The AP3842 and AP3844 have
UVLO thresholds of 16V(on) and 10V(off), ideally
suited for off-line applications. The corresponding
thresholds for the AP3843 and AP3845 are 8.5V
and 7.6V. The AP3842 and AP3843 can operate to
duty cycles approaching 100%. A range of the zero
to < 50% is obtained by the AP3844 and AP3845
by the addition of an internal toggle flip flop which
blanks the output off every other clock cycle.
Optimized for Off-Line and DC to DC Converters
Low Start-Up Current (≦0.5mA)
Automatic Feed Forward Compensation
Pulse-by-Pulse Current Limiting
Enhanced Load Response Characteristics
Under-Voltage Lockout (UVLO) with Hysteresis
Double Pulse Suppression
High Current Totem Pole Output
Internally Trimmed Bandgap Reference
Current Mode Operation to 500KHZ
Low Ro Error Amplifier
Pin Connections
PDIP-8L, SOP-8L
Top View
COMP.
V
FB
I
SENSE
R
T
/C
T
1
2
3
4
8
7
6
5
V
REF
V
I
OUTPUT
GROUND
Ordering Information
AP 384X X X X
Part No.
2:3842
3:3843
4:3844
5:3845
Package
S8:SOP-8L
N8:PDIP-8L
Lead Free
Packing
Blank: Tube
Blank : Normal
L : Lead Free Package A : Taping
This datasheet contains new product information. Anachip Corp. reserves the rights to modify the product specification without notice. No liability is assumed as a result of the use of
this product. No rights under any patent accompany the sale of the product.
Rev.1.0 Oct.11, 2004
1/8
Not Recommended for New Design
AP3842/3/4/5
High Performance Current Mode PWM Controller
Block Diagram
( toggle flip flop used only in AP3844 and AP3845 )
Vi
7
36V
UVLO
GROUND
5
16V
5V
S/R
REF
8
INTERNAL
BIAS
VREF
5V 50mA
2.50V
VREF GOOD
LOGIC
T
2R
R
S
R
1V
CURRENT
SENSE
COMPARATOR
PWM
LATCH
6
RT/CT
4
OUTPUT
OSC.
ERROR AMP.
2
VFB
COMP
CURRENT
SENSE
1
3
AP384X
Absolute Maximum Ratings
Symbol
V
i
V
i
I
o
E
o
P
tot
P
tot
T
stg
T
L
Parameter
Supply Voltage (low impedance source)
Supply Voltage (li < 30mA)
Output Current
Output Energy (capacitive load)
Analog Inputs (pins2,3)
Error Amplifier Output Sink Current
Power Dissipation at T
amb
≦
50
0
C (PDIP8)
Power Dissipation at T
amb
≦
25
0
C (SOP8)
Storage Temperature Range
Lead Temperature (soldering 10s)
Value
36
Self Limiting
±0.7
5
-0.3 to 5.5
10
1.25
800
-65 to 150
260
Unit
V
A
µJ
V
mA
W
mW
o
C
o
C
*Notes: 1. All voltages are with respect to pin 5, all currents are positive into the specified terminal.
Electrical Characteristics
(Unless otherwise stated, these specifications apply for
0≦T
amb
≦70
C for AP384X ; V
i
= 15V(note 5); R
T
= 10KΩ;C
T
= 3.3nF)
o
Symbol
Parameter
Test Conditions
AP384X
Min. Typ. Max.
Unit
REFERENCE SECTION
V
REF
Output Voltage
∆V
REF
Line Regulation
∆V
REF
Load Regulation
∆V
REF/
∆T
Temperature Stability
Total Output Variation
e
N
I
SC
Tj = 25
0
C I
0
=1mA
4.90 5.00 5.10
V
12V
≦
V
i
≦
25V
2
20
mV
1mA
≦
I
o
≦
20mA
3
25
mV
(Notes 2)
0.2 0.4 mV/
0
C
Line, Load, Temperature (Notes 2) 4.82
5.18
V
0
10Hz≦f
≦
10KHz Tj=25 C (Notes
50
µV
Output Noise Voltage
2)
0
Long Term Stability
T
amb
=125 C, 1000Hrs (Notes 2)
5
25
mV
Output Short Circuit current
-85 -120 mA
Anachip Corp.
www.anachip.com.tw
2/8
Rev.1.0 Oct.11, 2004
Not Recommended for New Design
AP3842/3/4/5
High Performance Current Mode PWM Controller
Electrical Characteristics(Continued)
(Unless otherwise stated, these specifications apply for
0≦T
amb
≦70
C for AP384X ; V
i
= 15V(note 5); R
T
= 10KΩ;C
T
= 3.3nF)
o
Symbol
Parameter
Test Conditions
Tj=25
0
C (Notes 6, 7)
12V
≦
V
i
≦
25V
T
MIN
≦
T
amb
≦
T
MAX
(Notes 2)
V
PIN4
Peak to Peak
0
Tj=25 C V
PIN4
=2V
V
PIN1
=2.5V
V
FB
=5V
0V
≦
V
0
≦
4V
Tj=25
o
C
12V
≦
V
i
≦
25V
V
PIN2
=2.7V V
PIN1
=1.1V
V
PIN2
=2.3V V
PIN1
=5V
V
PIN2
=2.3V; R
L
=15KΩ to ground
V
PIN2
=2.7V; R
L
=15KΩ to pin 8
(Notes3&Notes4)
V
PIN1
=5V (Notes3)
12
≦
V
i
≦
25V (Notes3)
AP384X
Min. Typ. Max.
49
52
0.2
0.5
1.6
8.3
55
1
Unit
KHz
%
%
V
mA
V
µA
dB
MHz
dB
mA
mA
V
V
V/V
V
dB
µA
ns
V
V
V
V
ns
ns
V
V
V
V
V
%
%
%
mA
mA
V
OSCILLATOR SECTION
f
s
Oscillator Frequency
Voltage Stability
Temperature Stability
V
4
Amplitude
Discharge Current
ERROR AMP SECTION
V
2
Feedback Input Voltage
I
b
Input Bias Current
A
VOL
B
Unity Gain Bandwidth
Supply Voltage Rejection
SVRR
Ratio
I
O
Output Sink Current
I
O
Output Source Current
V
OUT
High
V
OUT
Low
CURRENT SENSE SECTION
G
v
Gain
V
3
Maximum Input Signal
Supply Voltage Rejection
SVRR
Ratio
I
b
Input Bias Current
Delay to Output
OUTPUT SECTION
V
OL
V
OH
Output Low Level
Output High Level
7.8
8.8
2.42 2.50 2.58
-0.1
-2
65
90
0.7
1
60
2
-0.5
5
70
6
-0.8
7
0.8
3
1
70
-2
150
-10
300
0.4
2.2
1.1
3.15
1.1
2.85
0.9
T
r
Rise Time
T
f
Fall Time
V
OLS
UVLO Saturation
UNDER-VOLTAGE LOCKOUT SECTION
Start Threshold
Min Operating Voltage After
Turn-on
PWM SECTION
Maximum Duty Cycle
Minimum Duty Cycle
TOTAL STANDBY CURRENT
I
st
I
i
V
iz
Start-up Current
Operating Supply Current
Zener Voltage
I
SINK
= 20mA
I
SINK
= 200mA
I
SOURCE
= 20mA
I
SOURCE
= 200mA
Tj=25
0
C C
L
=1nF (Notes2)
Tj=25
0
C C
L
=1nF (Notes2)
Vcc = 6V ; Isink = 1mA
3842/4
3843/5
3842/4
3843/5
3842/3
3844/5
13
12
0.1
1.6
13.5
13.5
50
50
0.1
16
8.4
10
7.6
96
48
150
150
1.1
17.5
9
11.5
8.2
14.5
7.8
8.5
7.0
94
47
50
0
0.5
17
Vi=14V,3842/4 ;
Vi=6.5V 3843/5
V
PIN2
=V
PIN3
=0V
I
i
=25mA
0.3
30
12
36
Anachip Corp.
www.anachip.com.tw
3/8
Rev.1.0 Oct.11, 2004
Not Recommended for New Design
AP3842/3/4/5
High Performance Current Mode PWM Controller
Notes：2.These parameters, although guaranteed, are not 100% tested in production.
3.Parameter measured at trip point of latch with V
PIN2
=0.
4.Gain defined as:
∆V
PIN1
; 0≦V
PIN3
≦0.8V
A=
∆V
PIN3
5.Adjust V
i
above the start threshold before setting at 15V.
6.Output frequency equals oscillator frequency for the AP3842 and AP3843.
7.Output frequency is one and half oscillator frequency for the AP3844 and AP3845.
Figure 1 : Error Amp Configuration.
2.5V
0.8 mA
Zf
Zf
2
COMP
1
V
FB
Error amp can source or sink up to 0.5mA
Figure 2 : Under Voltage Lockout.
ON/OFF COMMAND
TO REST OF IC
I
CC
V
i
7
AP3842 AP3843
AP3844 AP3845
V
<17 mA
ON
16V
10V
8.4V
7.6V
<1 mA
V
V
OFF
OFF
V
ON
V
CC
During Under-Voltage Lockout, the output driver is biased to sink minor amounts of current. Pin 6 should be
shunted to ground with a bleeder resistor to prevent activating the power switch with extraneous leakage
currents.
Figure 3 : Current Sense Circuit.
ERROR
AMP
I
S
2R
COMP
R
C
3
1
CURRENT
SENSE
R
1V
CURRENT
SENSE
COMPARATOR
Rs
5
GND
Anachip Corp.
www.anachip.com.tw
4/8
Rev.1.0 Oct.11, 2004
Not Recommended for New Design
AP3842/3/4/5
High Performance Current Mode PWM Controller
Peak current(i
s
) is determined by the formula
1.0V
I
S
max
≈
R
S
A small RC filter may be required to suppress switch transients.
Figure 4.
V
REF
R
T
/C
T
GROUND
8
R
T
4
C
T
5
for R
T
> 5KΩ f=
1.72
R
T
C
T
Figure 5 : Open Loop Test Circuit.
V
REF
R
T
A
1
COMP.
V
FB
V
REF
4.7K
2N2222
8
7
6
5
0.1
uF
Vi
100K
ERROR AMP.
ADJUST
2
1K
I
SENSE
V
i
5K
AP3842
3
4
I
SENSE
ADJUST
4.7K
OUTPUT
0.1
uF
TW
1K
OUTPUT
R
T/
C
T
GROUND
C
GROUND
T
High peak currents associated with capacitive loads necessitate careful grounding techniques. Timing and
bypass apacitors should be connected close to pin 5 in a single point ground. The transistor and 5 KΩ
potentiometer are used to sample the oscillator waveform and apply an adjustable ramp to pin 3.
I use g_hSetupDisplay = GUI_CreateDialogBox(aDialogCreate1,10,&SetupDisplayCallback,0,0,0) created 5 controls, including 2 buttons and 3 EDITs. I want to switch between controls by judging when the ex...
Related articles:
[GD32L233C-START Review] 1. GD32L233C-START with obvious advantages and disadvantages (unboxing)
[GD32L233C-START Review] 2. Non-blocking way to light up, blink, blink, blink...
[GD3...
The Real Time Clock (RTC) is a set of counters that measure time. It can continue to run even when the system loses power. The RTC clock in the LPC1768 microcontroller can be a separate 32Khz clock so...
I wrote a program similar to a plug-in for a software in wince. However, when I am operating the software, I don’t want others to see the process, so I hope to implement a function similar to a screen...
Circuit boards are the carriers of electronic circuits. Any circuit design needs to be installed on a circuit board to realize its function. Processing circuit boards is the most headache for amateur ...
Google's driverless technology is not only an eye-catching technology, but also a subversion of the car usage model.
Those who have watched anti-terrorism films and TV dramas must have been im...[Details]
1 Introduction
As an emerging microfabrication technology, micro-electromechanical system (MEMS) technology has begun to be applied in various fields. It can integrate functions such as inform...[Details]
Overview
As a remote network communication control method with advanced technology, high reliability, complete functions and reasonable cost, CAN-bus has been widely used in various automa...[Details]
The automotive lighting and signal control system is responsible for controlling the vehicle's lighting, signal lights, electric horns, reversing and brake buzzers. Traditional automotive lighting...[Details]
The typical fault troubleshooting listed below is for reference of maintenance personnel.
When the computer is turned on, the indicator light is off and there is no screen display
Mainte...[Details]
Flooded Batteries
This battery developed in Germany can be used to power flashlights, strobe lights and toys as long as it is filled with water. This battery can be stored for 50 years and can...[Details]
Introduction
Liquid crystal, as a display device, is widely used in low-power products such as instruments, meters, and electronic equipment with its unique advantages. In the past, the displ...[Details]
Since AC mains power may experience power outages, voltage sags and surges, continuous undervoltage and overvoltage, and frequency fluctuations during supply, these factors will affect the continuous ...[Details]
1 Introduction
With the rapid economic development, my country's electricity demand has been growing at a rate of more than 20% per year. According to the current economic development trend an...[Details]
There are many types and styles of digital voltmeters in design and development. Traditional digital voltmeters have their own characteristics. They are suitable for manual measurement on site. Tra...[Details]
Current sensing in automotive applications includes controlling the current through solenoids and injectors. For example, during diesel injection, we rapidly increase the current to the induction i...[Details]
Li/SOCl2 batteries (lithium sub-cells) have the advantages of high operating voltage, stable discharge voltage, wide operating temperature range and long storage life, and have been widely used in ...[Details]
As a type of iron battery, lithium iron phosphate battery (hereinafter referred to as lithium iron battery) has always been widely concerned by industry friends (some people say that lithium iron b...[Details]
1. Driver IC Product Range
IR provides users with a variety of driver integrated circuits from single-phase to three-phase bridge. All types use highly integrated level conversion technol...[Details]
The 8051 microcontroller is the most common microcontroller we have. I have been using 8051 for a long time and have also taught microcontroller courses for a period of time. Here I would like to s...[Details]
Real-time operating system RTOS
京公网安备 11010802033920号
EEWORLD
